diff --git a/kernel/branches/net/drivers/R6040.asm b/kernel/branches/net/drivers/R6040.asm index 88c390f5fc..3cf983fe38 100644 --- a/kernel/branches/net/drivers/R6040.asm +++ b/kernel/branches/net/drivers/R6040.asm @@ -24,11 +24,28 @@ format MS COFF DEBUG equ 1 __DEBUG__ equ 1 - __DEBUG_LEVEL__ equ 1 + __DEBUG_LEVEL__ equ 2 - TX_RING_SIZE equ 4 + W_MAX_TIMEOUT equ 0x0FFF ; max time out delay time + + TX_TIMEOUT equ 6000 ; Time before concluding the transmitter is hung, in ms + + TX_RING_SIZE equ 4 ; RING sizes must be a power of 2 RX_RING_SIZE equ 4 + RX_BUF_LEN_IDX equ 3 ; 0==8K, 1==16K, 2==32K, 3==64K + +; Threshold is bytes transferred to chip before transmission starts. + + TX_FIFO_THRESH equ 256 ; In bytes, rounded down to 32 byte units. + +; The following settings are log_2(bytes)-4: 0 == 16 bytes .. 6==1024. + + RX_FIFO_THRESH equ 4 ; Rx buffer level before first PCI xfer. + RX_DMA_BURST equ 4 ; Maximum PCI burst, '4' is 256 bytes + TX_DMA_BURST equ 4 + + include 'proc32.inc' include 'imports.inc' @@ -39,43 +56,13 @@ public START public service_proc public version +; Operational parameters that usually are not changed. -; ethernet address length -ETH_ALEN equ 6 -ETH_HLEN equ (2 * ETH_ALEN + 2) -ETH_ZLEN equ 60 ; 60 + 4bytes auto payload for mininmum 64bytes frame length - -; system timer frequency -HZ equ 1000 - -; max time out delay time -W_MAX_TIMEOUT equ 0x0FFF - -;; Size of the in-memory receive ring. -RX_BUF_LEN_IDX equ 3 ;; 0==8K, 1==16K, 2==32K, 3==64K -RX_BUF_LEN equ (8192 << RX_BUF_LEN_IDX) - -;; PCI Tuning Parameters -; Threshold is bytes transferred to chip before transmission starts. -TX_FIFO_THRESH equ 256 ;; In bytes, rounded down to 32 byte units. - -;; The following settings are log_2(bytes)-4: 0 == 16 bytes .. 6==1024. -RX_FIFO_THRESH equ 4 ;; Rx buffer level before first PCI xfer. -RX_DMA_BURST equ 4 ;; Maximum PCI burst, '4' is 256 bytes -TX_DMA_BURST equ 4 - -;; Operational parameters that usually are not changed. PHY1_ADDR equ 1 ;For MAC1 PHY2_ADDR equ 3 ;For MAC2 PHY_MODE equ 0x3100 ;PHY CHIP Register 0 PHY_CAP equ 0x01E1 ;PHY CHIP Register 4 -;; Time in jiffies before concluding the transmitter is hung. -TX_TIMEOUT equ ((6000*HZ)/1000) - -IO_SIZE equ 256 ; RDC MAC I/O Size -MAX_MAC equ 2 ; MAX RDC MAC - ;************************************************************************** ; RDC R6040 Register Definitions ;************************************************************************** @@ -139,9 +126,7 @@ PHY_CC equ 0x88 ;PHY status change configuration register PHY_ST equ 0x8A ;PHY status register MAC_SM equ 0xAC ;MAC status machine MAC_ID equ 0xBE ;Identifier register -;?[ -;TX_DCNT equ 0x80 ;TX descriptor count -;RX_DCNT equ 0x80 ;RX descriptor count + MAX_BUF_SIZE equ 0x600 ;1536 MBCR_DEFAULT equ 0x012A ;MAC Bus Control Register @@ -169,6 +154,11 @@ RX_INTS equ RX_FIFO_FULL or RX_NO_DESC or RX_FINISH TX_INTS equ TX_FINISH INT_MASK equ RX_INTS or TX_INTS +RX_BUF_LEN equ (8192 << RX_BUF_LEN_IDX) ; Size of the in-memory receive ring. + +IO_SIZE equ 256 ; RDC MAC I/O Size +MAX_MAC equ 2 ; MAX RDC MAC + virtual at 0 x_head: @@ -333,7 +323,7 @@ proc service_proc stdcall, ioctl:dword find_irq [device.pci_bus], [device.pci_dev], [device.irq_line] - DEBUGF 2,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\ + DEBUGF 1,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\ [device.pci_dev]:1,[device.pci_bus]:1,[device.irq_line]:1,[device.io_addr]:4 ; Ok, the eth_device structure is ready, let's probe the device @@ -359,11 +349,11 @@ proc service_proc stdcall, ioctl:dword ; If the device was already loaded, find the device number and return it in eax .find_devicenum: - DEBUGF 2,"Trying to find device number of already registered device\n" + DEBUGF 1,"Trying to find device number of already registered device\n" call NetPtrToNum ; This kernel procedure converts a pointer to device struct in ebx ; into a device number in edi mov eax, edi ; Application wants it in eax instead - DEBUGF 2,"Kernel says: %u\n", eax + DEBUGF 1,"Kernel says: %u\n", eax ret ; If an error occured, remove all allocated data and exit (returning -1 in eax) @@ -392,12 +382,12 @@ endp ;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;; -macro r6040_mdio_write reg, val { - stdcall r6040_phy_read, [io_addr], [r6040_private.phy_addr], reg +macro mdio_write reg, val { + stdcall phy_read, [device.io_addr], [device.phy_addr], reg } -macro r6040_mdio_write reg, val { - stdcall r6040_phy_write, [io_addr], [r6040_private.phy_addr], reg, val +macro mdio_write reg, val { + stdcall phy_write, [device.io_addr], [devce.phy_addr], reg, val } @@ -447,15 +437,9 @@ probe: or eax, dword [device.mac] test eax, eax jnz @f - DEBUGF 1, "MAC address not initialized\n" ;, generating random" + DEBUGF 2, "ERROR: MAC address not initialized!\n" - ;Asper: Add here generate function call! - ; Temporary workaround: init by constant adress - - mov dword [device.mac], 0x00006000 - mov word [device.mac+4], 0x0001 @@: - ; Init RDC private data mov [device.mcr0], 0x1002 ;mov [private.phy_addr], 1 ; Asper: Only one network card is supported now. @@ -465,7 +449,7 @@ probe: stdcall phy_read, 1, 2 cmp ax, 0xFFFF jne @f - DEBUGF 1, "Failed to detect an attached PHY\n" ;, generating random" + DEBUGF 2, "Failed to detect an attached PHY\n" ;, generating random" mov eax, -1 ret @@: @@ -492,15 +476,16 @@ probe: stdcall phy_write, eax, 4, PHY_CAP stdcall phy_write, eax, 0, PHY_MODE -; if PHY_MODE = 0x3100 + if PHY_MODE = 0x3100 call phy_mode_chk mov [device.phy_mode], ax jmp .phy_readen -; end if + end if -; if not (PHY_MODE and 0x0100) + if not (PHY_MODE and 0x0100) mov [device.phy_mode], 0 -; end if + end if + .phy_readen: ; Set duplex mode @@ -527,7 +512,7 @@ probe: align 4 reset: - DEBUGF 1,"Resetting R6040\n" + DEBUGF 2,"Resetting R6040\n" ; Mask off Interrupt xor ax, ax @@ -539,11 +524,11 @@ reset: ; attach int handler movzx eax, [device.irq_line] - DEBUGF 1,"Attaching int handler to irq %x\n", eax:1 + DEBUGF 2,"Attaching int handler to irq %x\n", eax:1 stdcall AttachIntHandler, eax, int_handler, dword 0 test eax, eax jnz @f - DEBUGF 1,"\nCould not attach int handler!\n" + DEBUGF 2,"\nCould not attach int handler!\n" ; or eax, -1 ; ret @@: @@ -651,7 +636,7 @@ init_txbufs: .next_desc: mov [esi + x_head.ndesc], eax - mov [edi + x_head.skb_ptr], 0 + mov [esi + x_head.skb_ptr], 0 mov [esi + x_head.status], DSC_OWNER_MAC add eax, x_head.sizeof @@ -664,8 +649,6 @@ init_txbufs: GetRealAddr mov [device.tx_ring + x_head.sizeof*(TX_RING_SIZE - 1) + x_head.ndesc], eax - DEBUGF 1,"ok\n" - ret @@ -682,17 +665,14 @@ init_rxbufs: mov ecx, RX_RING_SIZE .next_desc: - DEBUGF 1,"esi=0x%x, edx=0x%x, ", esi, edx - mov [esi + x_head.ndesc], edx + mov [esi + x_head.ndesc], edx push esi ecx - stdcall KernelAlloc, dword 2000 + stdcall KernelAlloc, MAX_BUF_SIZE pop ecx esi - DEBUGF 1,"eax=0x%x, ", eax mov [esi + x_head.skb_ptr], eax GetRealAddr - DEBUGF 1,"eax=0x%x\n", eax mov [esi + x_head.buf], eax mov [esi + x_head.status], DSC_OWNER_MAC @@ -708,8 +688,6 @@ init_rxbufs: GetRealAddr mov [device.rx_ring + x_head.sizeof*(RX_RING_SIZE - 1) + x_head.ndesc], eax - DEBUGF 1,"ok\n" - ret @@ -725,10 +703,6 @@ phy_mode_chk: test eax, 0x4 jz .ret_0x8000 -; jnz @f -; mov eax, 0x8000 ; Link Failed, full duplex -; @@: - ; PHY Chip Auto-Negotiation Status movzx eax, [device.phy_addr] stdcall phy_read, eax, 1 @@ -774,9 +748,9 @@ phy_mode_chk: ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; align 4 transmit: - DEBUGF 1,"\nTransmitting packet, buffer:%x, size:%u\n", [esp+4], [esp+8] + DEBUGF 2,"\nTransmitting packet, buffer:%x, size:%u\n", [esp+4], [esp+8] mov eax, [esp+4] - DEBUGF 1,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\ + DEBUGF 2,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\ [eax+00]:2,[eax+01]:2,[eax+02]:2,[eax+03]:2,[eax+04]:2,[eax+05]:2,\ [eax+06]:2,[eax+07]:2,[eax+08]:2,[eax+09]:2,[eax+10]:2,[eax+11]:2,\ [eax+13]:2,[eax+12]:2 @@ -791,20 +765,22 @@ transmit: add edi, ebx add edi, device.tx_ring - ebx - DEBUGF 1,"R6040: TX buffer status: 0x%x\n", [edi + x_head.status]:4 + DEBUGF 2,"TX buffer status: 0x%x\n", [edi + x_head.status]:4 - test [edi + x_head.status], 0x8000 ; check if buffer is available + test [edi + x_head.status], DSC_OWNER_MAC ; check if buffer is available jnz .wait_to_send .do_send: + DEBUGF 2,"Sending now\n" + mov eax, [esp+4] mov [edi + x_head.skb_ptr], eax GetRealAddr mov [edi + x_head.buf], eax mov ecx, [esp+8] mov [edi + x_head.len], cx - mov [edi + x_head.status], 0x8000 + mov [edi + x_head.status], DSC_OWNER_MAC ; Trigger the MAC to check the TX descriptor mov ax, 0x01 @@ -813,27 +789,31 @@ transmit: out dx, ax inc [device.cur_tx] - and [device.cur_tx], TX_RING_SIZE-1 + and [device.cur_tx], TX_RING_SIZE - 1 xor eax, eax ret 8 .wait_to_send: -; mov ecx, [timer_ticks] -; add ecx, 100 -; .l2: -; test [eax + x_head.status], 0x8000 -; jz .do_send -; mov esi, 10 -; call Sleep -; cmp ecx, [timer_ticks] -; jl .l2 + DEBUGF 2,"Waiting for TX buffer\n" + call GetTimerTicks ; returns in eax + lea edx, [eax + 100] + .l2: + test [edi + x_head.status], DSC_OWNER_MAC + jz .do_send + mov esi, 10 + call Sleep + call GetTimerTicks + cmp edx, eax + jl .l2 + + DEBUGF 1,"Send timeout\n" xor eax, eax dec eax .fail: - DEBUGF 1,"Send timeout\n" + DEBUGF 1,"Send failed\n" ret 8 @@ -848,7 +828,7 @@ transmit: align 4 int_handler: - DEBUGF 1,"\nIRQ %x ", eax:2 ; no, you cant replace 'eax:2' with 'al', this must be a bug in FDO + DEBUGF 2,"\nIRQ %x ", eax:2 ; no, you cant replace 'eax:2' with 'al', this must be a bug in FDO ; Find pointer of device wich made IRQ occur @@ -866,7 +846,7 @@ int_handler: in ax, dx out dx, ax ; send it back to ACK - DEBUGF 1,"MISR=%x\n", eax:4 + DEBUGF 2,"MISR=%x\n", eax:4 ; Check if we are interessed in some of the reasons @@ -906,7 +886,7 @@ int_handler: test cx, DSC_OWNER_MAC jnz .no_RX - DEBUGF 1,"packet status=0x%x\n", cx + DEBUGF 2,"packet status=0x%x\n", cx test cx, DSC_RX_ERR ; Global error status set jnz .no_RX @@ -925,12 +905,12 @@ int_handler: push ecx push [edx + x_head.skb_ptr] - DEBUGF 1,"packet ptr=0x%x\n", [edx + x_head.skb_ptr] + DEBUGF 2,"packet ptr=0x%x\n", [edx + x_head.skb_ptr] ; reset the RX descriptor push edx - stdcall KernelAlloc, 2000 + stdcall KernelAlloc, MAX_BUF_SIZE pop edx mov [edx + x_head.skb_ptr], eax GetRealAddr @@ -958,22 +938,21 @@ int_handler: lea edi, [device.tx_ring + edi] test [edi + x_head.status], DSC_OWNER_MAC - jnz .tx_loop_end + jnz .no_TX cmp [edi + x_head.skb_ptr], 0 - je .tx_loop_end + je .no_TX - DEBUGF 1,"Freeing buffer 0x%x\n", [edi + x_head.skb_ptr] + DEBUGF 2,"Freeing buffer 0x%x\n", [edi + x_head.skb_ptr] push [edi + x_head.skb_ptr] - call KernelFree mov [edi + x_head.skb_ptr], 0 + call KernelFree inc [device.last_tx] and [device.last_tx], TX_RING_SIZE - 1 - jmp .loop_tx - .tx_loop_end: + jmp .loop_tx .no_TX: pop ax @@ -985,7 +964,7 @@ int_handler: align 4 init_mac_regs: - DEBUGF 1,"initializing MAC regs\n" + DEBUGF 2,"initializing MAC regs\n" ; MAC operation register mov ax, 1 @@ -1014,7 +993,7 @@ init_mac_regs: align 4 proc phy_read stdcall, phy_addr:dword, reg:dword - DEBUGF 1,"PHY read, addr=0x%x reg=0x%x\n", [phy_addr]:8, [reg]:8 + DEBUGF 2,"PHY read, addr=0x%x reg=0x%x\n", [phy_addr]:8, [reg]:8 mov eax, [phy_addr] shl eax, 8 @@ -1038,7 +1017,7 @@ proc phy_read stdcall, phy_addr:dword, reg:dword in ax, dx and eax, 0xFFFF - DEBUGF 1,"PHY read, val=0x%x\n", eax:4 + DEBUGF 2,"PHY read, val=0x%x\n", eax:4 ret @@ -1052,7 +1031,7 @@ endp align 4 proc phy_write stdcall, phy_addr:dword, reg:dword, val:dword - DEBUGF 1,"PHY write, addr=0x%x reg=0x%x val=0x%x\n", [phy_addr]:8, [reg]:8, [val]:8 + DEBUGF 2,"PHY write, addr=0x%x reg=0x%x val=0x%x\n", [phy_addr]:8, [reg]:8, [val]:8 mov eax, [val] set_io 0 @@ -1078,7 +1057,7 @@ proc phy_write stdcall, phy_addr:dword, reg:dword, val:dword jnz .write @@: - DEBUGF 1,"PHY write ok\n" + DEBUGF 2,"PHY write ok\n" ret endp