2009-09-17 13:55:38 +02:00
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Copyright (C) KolibriOS team 2004-2008. All rights reserved. ;;
;; Distributed under terms of the GNU General Public License ;;
;; ;;
;; Realtek 8139 driver for KolibriOS ;;
;; ;;
;; Written by hidnplayr@kolibrios.org ;;
;; ;;
;; v0.1 - march 2009 ;;
;; ;;
;; GNU GENERAL PUBLIC LICENSE ;;
;; Version 2, June 1991 ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
format MS COFF
API_VERSION equ 0x01000100
DEBUG equ 1
__DEBUG__ equ 1
__DEBUG_LEVEL__ equ 1
include 'proc32.inc'
include 'imports.inc'
include 'fdo.inc'
OS_BASE equ 0 ;
new_app_base equ 0x60400000
PROC_BASE equ OS_BASE + 0x0080000
public START
public service_proc
public version
struc IOCTL {
.handle dd ?
.io_code dd ?
.input dd ?
.inp_size dd ?
.output dd ?
.out_size dd ?
}
virtual at 0
IOCTL IOCTL
end virtual
struc ETH_DEVICE {
; pointers to procedures
.unload dd ?
.reset dd ?
.transmit dd ?
.set_MAC dd ?
.get_MAC dd ?
.set_mode dd ?
.get_mode dd ?
; status & variables
.bytes_tx dq ?
.bytes_rx dq ?
.packets_tx dd ?
.packets_rx dd ?
.mode dd ? ; This dword contains cable status (10mbit/100mbit, full/half duplex, auto negotiation or not,..)
.name dd ?
.mac dp ?
; device specific
.rx_buffer dd ?
.tx_buffer dd ?
.rx_data_offset dd ?
.io_addr dd ?
.curr_tx_desc db ?
.pci_bus db ?
.pci_dev db ?
.irq_line db ?
.hw_ver_id db ?
.size:
}
virtual at 0
device ETH_DEVICE
end virtual
; PCI Bus defines
PCI_HEADER_TYPE equ 0x0e ;8 bit
PCI_BASE_ADDRESS_0 equ 0x10 ;32 bit
PCI_BASE_ADDRESS_5 equ 0x24 ;32 bits
PCI_BASE_ADDRESS_SPACE_IO equ 0x01
PCI_VENDOR_ID equ 0x00 ;16 bit
PCI_BASE_ADDRESS_IO_MASK equ 0xFFFFFFFC
; RTL8139 specific defines
MAX_RTL8139 equ 16 ; Max number of devices this driver may handle
TX_TIMEOUT equ 30 ; 300 milliseconds timeout
PCI_REG_CMD equ 0x04 ; command register
PCI_BIT_PIO equ 0 ; bit0: io space control
PCI_BIT_MMIO equ 1 ; bit1: memory space control
PCI_BIT_MASTER equ 2 ; bit2: device acts as a PCI master
REG_IDR0 equ 0x00
REG_MAR0 equ 0x08 ; multicast filter register 0
REG_MAR4 equ 0x0c ; multicast filter register 4
REG_TSD0 equ 0x10 ; transmit status of descriptor
REG_TSAD0 equ 0x20 ; transmit start address of descriptor
REG_RBSTART equ 0x30 ; RxBuffer start address
REG_COMMAND equ 0x37 ; command register
REG_CAPR equ 0x38 ; current address of packet read (word) R/W
REG_IMR equ 0x3c ; interrupt mask register
REG_ISR equ 0x3e ; interrupt status register
REG_TXCONFIG equ 0x40 ; transmit configuration register
REG_RXCONFIG equ 0x44 ; receive configuration register 0
REG_MPC equ 0x4c ; missed packet counter
REG_9346CR equ 0x50 ; serial eeprom 93C46 command register
REG_CONFIG1 equ 0x52 ; configuration register 1
REG_MSR equ 0x58
REG_CONFIG4 equ 0x5a ; configuration register 4
REG_HLTCLK equ 0x5b ; undocumented halt clock register
REG_BMCR equ 0x62 ; basic mode control register
REG_ANAR equ 0x66 ; auto negotiation advertisement register
REG_9346CR_WE equ 11b SHL 6
BIT_RUNT equ 4 ; total packet length < 64 bytes
BIT_LONG equ 3 ; total packet length > 4k
BIT_CRC equ 2 ; crc error occured
BIT_FAE equ 1 ; frame alignment error occured
BIT_ROK equ 0 ; received packet is ok
BIT_RST equ 4 ; reset bit
BIT_RE equ 3 ; receiver enabled
BIT_TE equ 2 ; transmitter enabled
BUFE equ 1 ; rx buffer is empty, no packet stored
BIT_ISR_TOK equ 2 ; transmit ok
BIT_ISR_RER equ 1 ; receive error interrupt
BIT_ISR_ROK equ 0 ; receive ok
BIT_TX_MXDMA equ 8 ; Max DMA burst size per Tx DMA burst
BIT_TXRR equ 4 ; Tx Retry count 16+(TXRR*16)
BIT_RXFTH equ 13 ; Rx fifo threshold
BIT_RBLEN equ 11 ; Ring buffer length indicator
BIT_RX_MXDMA equ 8 ; Max DMA burst size per Rx DMA burst
BIT_NOWRAP equ 7 ; transfered data wrapping
BIT_9356SEL equ 6 ; eeprom selector 9346/9356
BIT_AER equ 5 ; accept error packets
BIT_AR equ 4 ; accept runt packets
BIT_AB equ 3 ; accept broadcast packets
BIT_AM equ 2 ; accept multicast packets
BIT_APM equ 1 ; accept physical match packets
BIT_AAP equ 0 ; accept all packets
BIT_93C46_EEM1 equ 7 ; RTL8139 eeprom operating mode1
BIT_93C46_EEM0 equ 6 ; RTL8139 eeprom operating mode0
BIT_93C46_EECS equ 3 ; chip select
BIT_93C46_EESK equ 2 ; serial data clock
BIT_93C46_EEDI equ 1 ; serial data input
BIT_93C46_EEDO equ 0 ; serial data output
BIT_LWACT equ 4 ; see REG_CONFIG1
BIT_SLEEP equ 1 ; sleep bit at older chips
BIT_PWRDWN equ 0 ; power down bit at older chips
BIT_PMEn equ 0 ; power management enabled
BIT_LWPTN equ 2 ; see REG_CONFIG4
BIT_ERTXTH equ 16 ; early TX threshold
BIT_TOK equ 15 ; transmit ok
BIT_OWN equ 13 ; tx DMA operation is completed
BIT_ANE equ 12 ; auto negotiation enable
BIT_TXFD equ 8 ; 100base-T full duplex
BIT_TX equ 7 ; 100base-T
BIT_10FD equ 6 ; 10base-T full duplex
BIT_10 equ 5 ; 10base-T
BIT_SELECTOR equ 0 ; binary encoded selector CSMA/CD=00001
BIT_IFG1 equ 25
BIT_IFG0 equ 24
RBLEN equ 2 ; Receive buffer size: 0==8K 1==16k 2==32k 3==64k
TXRR equ 8 ; total retries = 16+(TXRR*16)
TX_MXDMA equ 6 ; 0=16 1=32 2=64 3=128 4=256 5=512 6=1024 7=2048
ERTXTH equ 8 ; in unit of 32 bytes e.g:(8*32)=256
RX_MXDMA equ 7 ; 0=16 1=32 2=64 3=128 4=256 5=512 6=1024 7=unlimited
RXFTH equ 7 ; 0=16 1=32 2=64 3=128 4=256 5=512 6=1024 7=no threshold
RX_CONFIG equ ( RBLEN shl BIT_RBLEN ) or \
( RX_MXDMA shl BIT_RX_MXDMA ) or \
( 1 shl BIT_NOWRAP ) or \
( RXFTH shl BIT_RXFTH ) or \
( 1 shl BIT_AB ) or \
( 1 shl BIT_APM ) or \
( 1 shl BIT_AER ) or \
( 1 shl BIT_AR ) or \
( 1 shl BIT_AM )
RX_BUFFER_SIZE equ ( 8192 shl RBLEN )
MAX_ETH_FRAME_SIZE equ 1516 ; exactly 1514 wthout CRC
NUM_TX_DESC equ 4
TX_BUF_SIZE equ 4096 ; size of one tx buffer (set to 4kb because of KolibriOS's page size)
EE_93C46_REG_ETH_ID equ 7 ; MAC offset
EE_93C46_READ_CMD equ ( 6 shl 6 ) ; 110b + 6bit address
EE_93C56_READ_CMD equ ( 6 shl 8 ) ; 110b + 8bit address
EE_93C46_CMD_LENGTH equ 9 ; start bit + cmd + 6bit address
EE_93C56_CMD_LENGTH equ 11 ; start bit + cmd + 8bit ddress
VER_RTL8139 equ 1100000b
VER_RTL8139A equ 1110000b
VER_RTL8139AG equ 1110100b
VER_RTL8139B equ 1111000b
VER_RTL8130 equ VER_RTL8139B
VER_RTL8139C equ 1110100b
VER_RTL8100 equ 1111010b
VER_RTL8100B equ 1110101b
VER_RTL8139D equ VER_RTL8100B
VER_RTL8139CP equ 1110110b
VER_RTL8101 equ 1110111b
IDX_RTL8139 equ 0
IDX_RTL8139A equ 1
IDX_RTL8139B equ 2
IDX_RTL8139C equ 3
IDX_RTL8100 equ 4
IDX_RTL8139D equ 5
IDX_RTL8139D equ 6
IDX_RTL8101 equ 7
ISR_SERR equ 1 SHL 15
ISR_TIMEOUT equ 1 SHL 14
ISR_LENCHG equ 1 SHL 13
ISR_FIFOOVW equ 1 SHL 6
ISR_PUN equ 1 SHL 5
ISR_RXOVW equ 1 SHL 4
ISR_TER equ 1 SHL 3
ISR_TOK equ 1 SHL 2
ISR_RER equ 1 SHL 1
ISR_ROK equ 1 SHL 0
INTERRUPT_MASK equ ISR_ROK or \
ISR_RXOVW or \
ISR_PUN or \
ISR_FIFOOVW or \
ISR_LENCHG or \
ISR_TOK or \
ISR_TER
TSR_OWN equ 1 SHL 13
TSR_TUN equ 1 SHL 14
TSR_TOK equ 1 SHL 15
TSR_CDH equ 1 SHL 28
TSR_OWC equ 1 SHL 29
TSR_TABT equ 1 SHL 30
TSR_CRS equ 1 SHL 31
section '.flat' code readable al ign 16
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; proc START ;;
;; ;;
;; (standard driver proc) ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
proc START stdcall , state : dword
cmp [ state ], 1
jne .exit
.entry:
DEBUGF 1 , "Loading rtl8139 driver\n"
stdcall RegService , my_service , service_proc
ret
.fail:
.exit:
xor eax , eax
ret
endp
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; proc SERVICE_PROC ;;
;; ;;
;; (standard driver proc) ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
proc service_proc stdcall , ioctl : dword
mov edx , [ ioctl ]
mov eax , [ ebx + IOCTL.io_code ]
;------------------------------------------------------
cmp eax , 0 ;SRV_GETVERSION
jne @ F
cmp [ edx + IOCTL.out_size ], 4
jl .fail
mov eax , [ edx + IOCTL.output ]
mov [ eax ], dword API_VERSION
xor eax , eax
ret
;------------------------------------------------------
@ @ :
cmp eax , 1 ;SRV_HOOK
jne .fail
cmp [ edx + IOCTL.inp_size ], 3 ; Data input must be at least 3 bytes
jl .fail
mov eax , [ edx + IOCTL.input ]
cmp byte [ eax ], 1 ; 1 means device number and bus number (pci) are given
jne .fail ; other types arent supported for this card yet
; check if the device is already listed
mov esi , RTL8139_LIST
mov ecx , [ RTL8139_DEV ]
test ecx , ecx
jz .firstdevice
; mov eax, [edx+IOCTL.input] ; get the pci bus and device numbers
mov bx , [ eax + 1 ] ;
.nextdevice:
lodsd
cmp bx , word [ eax + device.pci_bus ] ; compare with pci and device num in RTL8139 list (notice the usage of word instead of byte)
je .find_devicenum ; Device is already loaded, let's find it's device number
loop .nextdevice
; This device doesnt have its own eth_device structure yet, lets create one
.firstdevice:
cmp [ RTL8139_DEV ], MAX_RTL8139 ; First check if the driver can handle one more card
jge .fail
push edx
stdcall KernelAlloc , dword device.size ; Allocate the buffer for eth_device structure
pop edx
test eax , eax
jz .fail
mov ebx , eax ; ebx is always used as a pointer to the structure (in driver, but also in kernel code)
; Fill in the direct call addresses into the struct
mov dword [ ebx + device.reset ], reset
mov dword [ ebx + device.transmit ], transmit
mov dword [ ebx + device.get_MAC ], read_mac
mov dword [ ebx + device.set_MAC ], write_mac
mov dword [ ebx + device.unload ], unload
mov dword [ ebx + device.name ], devicename
; save the pci bus and device numbers
mov eax , [ edx + IOCTL.input ]
mov cl , [ eax + 1 ]
mov [ ebx + device.pci_bus ], cl
mov cl , [ eax + 2 ]
mov [ ebx + device.pci_dev ], cl
; Now, it's time to find the base io addres of the PCI device
; TODO: implement check if bus and dev exist on this machine
mov edx , PCI_BASE_ADDRESS_0
.reg_check:
movzx eax , byte [ ebx + device.pci_bus ]
movzx ecx , byte [ ebx + device.pci_dev ]
push edx ecx
stdcall PciRead16 , eax , ecx , edx
pop ecx edx
mov [ ebx + device.io_addr ], eax
and eax , PCI_BASE_ADDRESS_IO_MASK
test eax , eax
jz .inc_reg
mov eax , [ ebx + device.io_addr ]
and eax , PCI_BASE_ADDRESS_SPACE_IO
test eax , eax
jz .inc_reg
mov eax , [ ebx + device.io_addr ]
and eax , PCI_BASE_ADDRESS_IO_MASK
mov [ ebx + device.io_addr ], eax
jmp .got_io
.inc_reg:
add edx , 4
cmp edx , PCI_BASE_ADDRESS_5
jbe .reg_check
.got_io:
; We've found the io address, find IRQ now
movzx eax , byte [ ebx + device.pci_bus ]
movzx ecx , byte [ ebx + device.pci_dev ]
push ebx
stdcall PciRead8 , eax , ecx , 0x3c ; 0x3c is the offset where irq can be found
pop ebx
mov byte [ ebx + device.irq_line ], al
DEBUGF 1 , "Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n" , \
[ ebx + device.pci_dev ]: 1 ,[ ebx + device.pci_bus ]: 1 ,[ ebx + device.irq_line ]: 1 ,[ ebx + device.io_addr ]: 4
; Allocate the Receive buffer
stdcall KernelAlloc , dword ( RX_BUFFER_SIZE + MAX_ETH_FRAME_SIZE )
test eax , eax
jz .err
mov [ ebx + device.rx_buffer ], eax ; Save the address to it into the device struct
; Now, Clear the allocated buffer
cld
mov edi , eax
mov ecx , ( RX_BUFFER_SIZE ) / 4 ; divide by 4 because we are going to use DWORD
xor eax , eax
rep stosd
; Allocate the Transmit Buffer
stdcall KernelAlloc , dword ( TX_BUF_SIZE * NUM_TX_DESC )
test eax , eax
jz .err
mov [ ebx + device.tx_buffer ], eax
; This one needs to be cleared too..
mov edi , eax
mov ecx , ( TX_BUF_SIZE * NUM_TX_DESC ) / 4
xor eax , eax
rep stosd
; Ok, the eth_device structure is ready, let's probe the device
call probe ; this function will output in eax
test eax , eax
jnz .err ; If an error occured, exit
mov eax , [ RTL8139_DEV ] ; Add the device structure to our device list
mov [ RTL8139_LIST + 4 * eax ], ebx ; (IRQ handler uses this list to find device)
inc [ RTL8139_DEV ] ;
call EthRegDev
cmp eax , - 1
je .destroy
ret
; If the device was already loaded, find the device number and return it in eax
.find_devicenum:
DEBUGF 1 , "Trying to find device number of already registered device\n"
mov ebx , eax
call EthStruc2Dev ; This kernel procedure converts a pointer to device struct in ebx
; into a device number in edi
mov eax , edi ; Application wants it in eax instead
DEBUGF 1 , "Kernel says: %u\n" , eax
ret
; If an error occured, remove all allocated data and exit (returning -1 in eax)
.destroy:
; todo: reset device into virgin state
.err:
stdcall KernelFree , dword [ ebx + device.rx_buffer ]
stdcall KernelFree , dword [ ebx + device.tx_buffer ]
stdcall KernelFree , ebx
.fail:
or eax , - 1
ret
;------------------------------------------------------
endp
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
;; ;;
;; Actual Hardware dependent code starts here ;;
;; ;;
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
align 4
unload:
; TODO: (in this particular order)
;
; - Stop the device
; - Detach int handler
; - Remove device from local list (RTL8139_LIST)
; - call unregister function in kernel
; - Remove all allocated structures and buffers the card used
or eax , - 1
ret
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;
;; probe: enables the device (if it really is RTL8139)
;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
probe:
DEBUGF 2 , "Probing rtl8139 device: "
; enable the device
movzx eax , byte [ ebx + device.pci_bus ]
movzx ecx , byte [ ebx + device.pci_dev ]
stdcall PciRead32 , eax , ecx , PCI_REG_CMD
mov cx , ax
or cl , ( 1 shl PCI_BIT_MASTER ) or ( 1 shl PCI_BIT_PIO )
and cl , not ( 1 shl PCI_BIT_MMIO )
movzx eax , byte [ ebx + device.pci_bus ]
movzx edx , byte [ ebx + device.pci_dev ]
stdcall PciWrite32 , eax , edx , PCI_REG_CMD , ecx
; get chip version
mov edx , [ ebx + device.io_addr ]
add edx , REG_TXCONFIG + 2
in ax , dx
shr ah , 2
shr ax , 6
and al , 01111111b
mov ecx , HW_VER_ARRAY_SIZE - 1
.chip_ver_loop:
cmp al , [ hw_ver_array + ecx ]
je .chip_ver_found
dec ecx
jns .chip_ver_loop
xor cl , cl ; default RTL8139
.chip_ver_found:
mov [ ebx + device.hw_ver_id ], cl
; wake up the chip
mov edx , [ ebx + device.io_addr ]
add edx , REG_HLTCLK
mov al , 'R' ; run the clock
out dx , al
; unlock config and BMCR registers
add edx , REG_9346CR - REG_HLTCLK
mov al , ( 1 shl BIT_93C46_EEM1 ) or ( 1 shl BIT_93C46_EEM0 )
out dx , al
; enable power management
add edx , REG_CONFIG1 - REG_9346CR
in al , dx
cmp byte [ ebx + device.hw_ver_id ], IDX_RTL8139B
jl .old_chip
; set LWAKE pin to active high (default value).
; it is for Wake-On-LAN functionality of some motherboards.
; this signal is used to inform the motherboard to execute a wake-up process.
; only at newer chips.
or al , ( 1 shl BIT_PMEn )
and al , not ( 1 shl BIT_LWACT )
out dx , al
add edx , REG_CONFIG4 - REG_CONFIG1
in al , dx
and al , not ( 1 shl BIT_LWPTN )
out dx , al
jmp .finish_wake_up
.old_chip:
; wake up older chips
and al , not (( 1 shl BIT_SLEEP ) or ( 1 shl BIT_PWRDWN ))
out dx , al
.finish_wake_up:
; lock config and BMCR registers
xor al , al
mov edx , [ ebx + device.io_addr ]
add edx , REG_9346CR
out dx , al
DEBUGF 2 , "done!\n"
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;
;; reset: Set up all registers and descriptors, clear some values
;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
reset:
DEBUGF 2 , "Resetting rtl8139: "
; attach int handler
movzx eax , [ ebx + device.irq_line ]
DEBUGF 1 , "Attaching int handler to irq %x, " , eax : 1
stdcall AttachIntHandler , eax , int_handler , dword 0
test eax , eax
jnz @ f
DEBUGF 1 , "\nCould not attach int handler!\n"
; or eax, -1
; ret
@ @ :
; reset chip
DEBUGF 1 , "Resetting chip\n"
mov edx , [ ebx + device.io_addr ]
add edx , REG_COMMAND
mov al , 1 shl BIT_RST
out dx , al
mov cx , 1000 ; wait no longer for the reset
.wait_for_reset:
in al , dx
test al , 1 shl BIT_RST
jz .reset_completed ; RST remains 1 during reset
dec cx
jns .wait_for_reset
.reset_completed:
; unlock config and BMCR registers
mov edx , [ ebx + device.io_addr ]
add edx , REG_9346CR
mov al , ( 1 shl BIT_93C46_EEM1 ) or ( 1 shl BIT_93C46_EEM0 )
out dx , al
; initialize multicast registers (no filtering)
mov eax , 0xffffffff
add edx , REG_MAR0 - REG_9346CR
out dx , eax
add edx , REG_MAR4 - REG_MAR0
out dx , eax
; enable Rx/Tx
mov al , ( 1 shl BIT_RE ) or ( 1 shl BIT_TE )
add edx , REG_COMMAND - REG_MAR4
out dx , al
; 32k Rxbuffer, unlimited dma burst, no wrapping, no rx threshold
; accept broadcast packets, accept physical match packets
mov ax , RX_CONFIG
add edx , REG_RXCONFIG - REG_COMMAND
out dx , ax
; 1024 bytes DMA burst, total retries = 16 + 8 * 16 = 144
mov eax , ( TX_MXDMA shl BIT_TX_MXDMA ) or ( TXRR shl BIT_TXRR ) or BIT_IFG1 or BIT_IFG0
add edx , REG_TXCONFIG - REG_RXCONFIG
out dx , eax
; enable auto negotiation
add edx , REG_BMCR - REG_TXCONFIG
in ax , dx
or ax , ( 1 shl BIT_ANE )
out dx , ax
; set auto negotiation advertisement
add edx , REG_ANAR - REG_BMCR
in ax , dx
or ax , ( 1 shl BIT_SELECTOR ) or ( 1 shl BIT_10 ) or ( 1 shl BIT_10FD ) or ( 1 shl BIT_TX ) or ( 1 shl BIT_TXFD )
out dx , ax
; lock config and BMCR registers
xor eax , eax
add edx , REG_9346CR - REG_ANAR
out dx , al
; init RX/TX pointers
mov [ ebx + device.rx_data_offset ], eax
mov [ ebx + device.curr_tx_desc ], al
2009-09-22 18:42:54 +02:00
; clear packet/byte counters
lea edi , [ ebx + device.bytes_tx ] ; TODO: check if destroying edi, ecx doesnt harm anything
mov ecx , 6
rep stosd
2009-09-17 13:55:38 +02:00
; clear missing packet counter
add edx , REG_MPC - REG_9346CR
out dx , eax
; Set up the 4 Txbuffer descriptors
add edx , REG_TSAD0 - REG_MPC
mov eax , [ ebx + device.tx_buffer ]
mov ecx , 4
.loop:
push eax
call GetPgAddr
DEBUGF 2 , "Desc: %x " , eax
out dx , eax
add dx , 4
pop eax
add eax , TX_BUF_SIZE
loop .loop
; set RxBuffer address, init RX buffer offset, init TX ring
mov eax , [ ebx + device.rx_buffer ]
call GetPgAddr
mov edx , [ ebx + device.io_addr ]
add edx , REG_RBSTART
out dx , eax
; enable interrupts
mov eax , INTERRUPT_MASK
add edx , REG_IMR - REG_RBSTART
out dx , ax
; Read MAC address
call read_mac
; Indicate that we have successfully reset the card
DEBUGF 2 , "Done!\n"
xor eax , eax
ret
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Transmit ;;
;; ;;
;; In: buffer pointer in [esp] ;;
;; size of buffer in [esp+4] ;;
;; pointer to device structure in ebx ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
transmit:
DEBUGF 1 , "Transmitting packet, buffer:%x, size:%u\n" ,[ esp ],[ esp + 4 ]
mov eax , [ esp ]
DEBUGF 1 , "To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n" , \
[ eax + 00 ]: 2 ,[ eax + 01 ]: 2 ,[ eax + 02 ]: 2 ,[ eax + 03 ]: 2 ,[ eax + 04 ]: 2 ,[ eax + 05 ]: 2 , \
[ eax + 06 ]: 2 ,[ eax + 07 ]: 2 ,[ eax + 08 ]: 2 ,[ eax + 09 ]: 2 ,[ eax + 10 ]: 2 ,[ eax + 11 ]: 2 , \
[ eax + 13 ]: 2 ,[ eax + 12 ]: 2
cmp dword [ esp + 4 ], MAX_ETH_FRAME_SIZE
jg .finish ; packet is too long
cmp dword [ esp + 4 ], 60
jl .finish ; packet is too short
; check descriptor
; DEBUGF 1,"Checking descriptor, "
movzx ecx , [ ebx + device.curr_tx_desc ]
mov edx , [ ebx + device.io_addr ]
lea edx , [ edx + ecx * 4 + REG_TSD0 ]
in ax , dx
test ax , 0x1fff ; or no size given
jz .send_packet
and ax , ( 1 shl BIT_TOK ) or ( 1 shl BIT_OWN )
cmp ax , ( 1 shl BIT_TOK ) or ( 1 shl BIT_OWN )
jz .send_packet
; wait for timeout
; DEBUGF 1,"Waiting for timeout, "
push edx ebx ; TODO : rtl8139 internal timer should be used instead
stdcall Sleep , TX_TIMEOUT ; ? What registers does this destroy ?
pop ebx edx
in ax , dx
and ax , ( 1 shl BIT_TOK ) or ( 1 shl BIT_OWN )
cmp ax , ( 1 shl BIT_TOK ) or ( 1 shl BIT_OWN )
jz .send_packet ; if chip hung, reset it
push dx
call reset ; reset the card
pop dx
.send_packet:
; DEBUGF 1,"Sending packet, "
push edx
movzx eax , [ ebx + device.curr_tx_desc ] ; calculate the current tx_buffer address
mov edx , TX_BUF_SIZE ;MAX_ETH_FRAME_SIZE ;
mul edx ;
mov edi , [ ebx + device.tx_buffer ] ;
add edi , eax ; Store it in edi
pop edx
mov esi , [ esp ] ; Copy data to that address
mov ecx , [ esp + 4 ] ;
shr ecx , 2 ;
rep movsd ;
mov ecx , [ esp + 4 ] ;
and ecx , 3 ;
rep movsb ;
inc [ ebx + device.packets_tx ] ;
mov eax , [ esp + 4 ] ; Get packet size in eax
2009-09-22 18:42:54 +02:00
add dword [ ebx + device.bytes_tx + 4 ], eax
adc dword [ ebx + device.bytes_tx ], 0
2009-09-17 13:55:38 +02:00
; or eax, (ERTXTH shl BIT_ERTXTH) ; Set descriptor size and the early tx treshold into the correct Transmission status register (TSD0, TSD1, TSD2 or TSD3)
out dx , eax ;
; get next descriptor 0, 1, 2, 3, 0, 1, 2, 3, 0, 1, ...
inc [ ebx + device.curr_tx_desc ]
and [ ebx + device.curr_tx_desc ], 3
DEBUGF 2 , " - Packet Sent! "
.finish:
DEBUGF 2 , " - Done!\n"
call KernelFree
add esp , 4 ; pop (balance stack)
ret
;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Interrupt handler ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;
align 4
int_handler:
DEBUGF 1 , "IRQ %x " , eax : 2 ; no, you cant replace 'eax:2' with 'al', this must be a bug in FDO
; find pointer of device wich made IRQ occur
mov esi , RTL8139_LIST
mov ecx , [ RTL8139_DEV ]
.nextdevice:
mov ebx , dword [ esi ]
mov edx , dword [ ebx + device.io_addr ] ; get IRQ reason
add edx , REG_ISR
in ax , dx
out dx , ax ; send it back to ACK
add esi , 4
test ax , ax
jnz .got_it
loop .nextdevice
ret ; If no device was found, abort (The irq was probably for a device, not registered to this driver)
.got_it:
; looks like we've found it!
; Lets found out why the irq occured then..
;----------------------------------------------------
; Received packet ok?
test ax , ISR_ROK
jz @ f
push ax
.receive:
mov edx , dword [ ebx + device.io_addr ] ; get IRQ reason
add edx , REG_COMMAND ;
in al , dx ;
test al , BUFE ; test if RX buffer is empty
jnz .finish ;
DEBUGF 2 , "RX: "
mov eax , dword [ ebx + device.rx_buffer ]
add eax , dword [ ebx + device.rx_data_offset ]
test byte [ eax ], ( 1 shl BIT_ROK ) ; check if packet is ok
jz .reset_rx
; packet is ok, copy it
movzx ecx , word [ eax + 2 ] ; packet length
2009-09-22 18:42:54 +02:00
add dword [ ebx + device.bytes_rx + 4 ], ecx ; Update stats
adc dword [ ebx + device.bytes_rx ], 0
2009-09-17 13:55:38 +02:00
inc dword [ ebx + device.packets_rx ] ;
sub ecx , 4 ; don't copy CRC
DEBUGF 1 , "Received %u bytes\n" , ecx
push ebx eax ecx
stdcall KernelAlloc , ecx ; Allocate a buffer to put packet into
pop ecx
test eax , eax ; Test if we allocated succesfully
jz .abort ;
mov edi , eax ; Set up registers to copy the packet
mov esi , [ esp ] ;
add esi , 4 ; Dont copy CRC
push dword .abort ; Kernel will return to this address after EthReceiver
push ecx edi ; Save buffer pointer and size, to pass to kernel
shr ecx , 2
cld
rep movsd ; copy the dwords
mov ecx , [ esp + 4 ]
and ecx , 3
rep movsb ; copy the rest bytes
jmp EthReceiver ; Send it to kernel
.abort:
pop eax ebx
; update eth_data_start_offset
movzx eax , word [ eax + 2 ] ; packet length
add eax , [ ebx + device.rx_data_offset ]
add eax , 4 + 3 ; packet header is 4 bytes long + dword alignment
and eax , not 3 ; dword alignment
cmp eax , RX_BUFFER_SIZE
jl .no_wrap
sub eax , RX_BUFFER_SIZE
.no_wrap:
mov [ ebx + device.rx_data_offset ], eax
DEBUGF 1 , "New RX ptr: %u" , eax
mov edx , dword [ ebx + device.io_addr ]
add edx , REG_CAPR ; update 'Current Address of Packet Read register'
sub eax , 0x10 ; value 0x10 is a constant for CAPR
out dx , ax
jmp .receive ; check for multiple packets
.reset_rx:
test byte [ eax ], ( 1 shl BIT_CRC )
jz .no_crc_error
DEBUGF 2 , "\nCRC error!\n"
.no_crc_error:
test byte [ eax ], ( 1 shl BIT_FAE )
jz .no_fae_error
DEBUGF 1 , "\nFrame alignment error!\n"
.no_fae_error:
DEBUGF 1 , "Reset RX\n"
in al , dx ; read command register
push ax
and al , not ( 1 shl BIT_RE ) ; Clear the RE bit
out dx , al
pop ax
out dx , al ; write original command back
add edx , REG_RXCONFIG - REG_COMMAND ; Restore RX configuration
mov ax , RX_CONFIG
out dx , ax
.finish:
pop ax
;----------------------------------------------------
; Transmit error ?
@ @ :
test ax , ISR_TER
jz @ f
push ax
cmp [ ebx + device.curr_tx_desc ], 4
jz .notxd
mov edx , [ ebx + device.io_addr ]
movzx ecx , [ ebx + device.curr_tx_desc ]
lea edx , [ edx + ecx * 4 + REG_TSD0 ]
in eax , dx
.notxd:
test eax , TSR_TUN
jz .nobun
DEBUGF 1 , "TX: FIFO Buffer underrun!\n"
.nobun:
test eax , TSR_OWC
jz .noowc
DEBUGF 1 , "TX: OWC!\n"
.noowc:
test eax , TSR_TABT
jz .notabt
DEBUGF 1 , "TX: TABT!\n"
.notabt:
test eax , TSR_CRS
jz .nocsl
DEBUGF 1 , "TX: Carrier Sense Lost!\n"
.nocsl:
; test eax, TSR_OWN or TSR_TOK
; jz .nofd
; DEBUGF 1, "TX: Transmit OK (desc: %u)\n", ecx
;
; .nofd:
pop ax
;----------------------------------------------------
; Transmit ok ?
@ @ :
test ax , ISR_TOK
jz @ f
DEBUGF 1 , "TX: Transmit OK (desc: %u)\n" , [ ebx + device.curr_tx_desc ]: 1
;----------------------------------------------------
; Rx buffer overflow ?
@ @ :
test ax , ISR_RXOVW
jz @ f
push ax
DEBUGF 1 , "RX-buffer overflow!\n"
mov edx , [ ebx + device.io_addr ]
add edx , REG_ISR
mov ax , ISR_FIFOOVW or ISR_RXOVW
out dx , ax
pop ax
;----------------------------------------------------
; Packet underrun? ?
@ @ :
test ax , ISR_PUN
jz @ f
DEBUGF 1 , "Packet underrun!\n"
;----------------------------------------------------
; Receive FIFO overflow ?
@ @ :
test ax , ISR_FIFOOVW
jz @ f
push ax
DEBUGF 2 , "RX fifo overflox!\n"
mov edx , [ ebx + device.io_addr ]
add edx , REG_ISR
mov ax , ISR_FIFOOVW or ISR_RXOVW
out dx , ax
pop ax
;----------------------------------------------------
; Something about Cable changed ?
@ @ :
test ax , ISR_LENCHG
jz .fail
DEBUGF 2 , "Cable changed!\n"
call cable
; If none of the above events happened, just exit clearing int
.fail:
DEBUGF 2 , "\n"
ret
;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Update Cable status ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
cable:
DEBUGF 1 , "Checking Cable status: "
mov edx , dword [ ebx + device.io_addr ]
add edx , REG_MSR
in al , dx
; test al , 1 SHL 2 ; 0 = link ok 1 = link fail
; jnz .notconnected
; test al , 1 SHL 3 ; 0 = 100 Mbps 1 = 10 Mbps
; jnz .10mbps
shr al , 2
and al , 3
mov byte [ ebx + device.mode + 3 ], al
DEBUGF 1 , "Done!\n"
ret
;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Write MAC address ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;
align 4
write_mac: ; in: mac pushed onto stack (as 3 words)
DEBUGF 1 , "Writing MAC: "
; disable all in command registers
mov edx , [ ebx + device.io_addr ]
add edx , REG_9346CR
xor eax , eax
out dx , al
add edx , REG_IMR - REG_9346CR
xor eax , eax
out dx , ax
add edx , REG_ISR - REG_IMR
mov eax , - 1
out dx , ax
; enable writing
add edx , REG_9346CR - REG_ISR
mov eax , REG_9346CR_WE
out dx , al
; write the mac ...
add edx , REG_IDR0 - REG_9346CR
pop eax
out dx , eax
add edx , 4
xor eax , eax
pop ax
out dx , eax
; disable writing
add edx , REG_9346CR - REG_IDR0
xor eax , eax
out dx , al
DEBUGF 1 , "ok!\n"
; Notice this procedure does not ret, but continues to read_mac instead.
;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Read MAC address ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;
read_mac:
DEBUGF 1 , "Reading MAC: "
mov edx , [ ebx + device.io_addr ]
lea edi , [ ebx + device.mac ]
2009-09-24 12:43:38 +02:00
in eax , edx
2009-09-17 13:55:38 +02:00
stosd
2009-09-24 12:43:38 +02:00
add dx , 4
in ax , dx
2009-09-17 13:55:38 +02:00
stosw
2009-09-24 12:43:38 +02:00
DEBUGF 1 , "%x-%x-%x-%x-%x-%x\n" ,[ edi - 6 ]: 2 ,[ edi - 5 ]: 2 ,[ edi - 4 ]: 2 ,[ edi - 3 ]: 2 ,[ edi - 2 ]: 2 ,[ edi - 1 ]: 2
2009-09-17 13:55:38 +02:00
ret
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Read eeprom (type 93c46 and 93c56) ;;
;; ;;
;; In: word to be read in al (6bit in case of 93c46 and 8bit otherwise) ;;
;; pointer to device structure in ebx ;;
;; ;;
;; OUT: word read in ax ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
read_eeprom:
DEBUGF 2 , "Reading eeprom, "
mov edx , [ ebx + device.io_addr ]
push ebx
movzx ebx , al
add edx , REG_RXCONFIG
in al , dx
test al , ( 1 shl BIT_9356SEL )
jz .type_93c46
; and bl, 01111111b ; don't care first bit
or bx , EE_93C56_READ_CMD ; it contains start bit
mov cx , EE_93C56_CMD_LENGTH - 1 ; cmd_loop counter
jmp .read_eeprom
.type_93c46:
and bl , 00111111b
or bx , EE_93C46_READ_CMD ; it contains start bit
mov cx , EE_93C46_CMD_LENGTH - 1 ; cmd_loop counter
.read_eeprom:
add edx , REG_9346CR - REG_RXCONFIG
; mov al, (1 shl BIT_93C46_EEM1)
; out dx, al
mov al , ( 1 shl BIT_93C46_EEM1 ) or ( 1 shl BIT_93C46_EECS ) ; wake up the eeprom
out dx , al
.cmd_loop:
mov al , ( 1 shl BIT_93C46_EEM1 ) or ( 1 shl BIT_93C46_EECS )
bt bx , cx
jnc .zero_bit
or al , ( 1 shl BIT_93C46_EEDI )
.zero_bit:
out dx , al
; push eax
; in eax, dx ; eeprom delay
; pop eax
or al , ( 1 shl BIT_93C46_EESK )
out dx , al
; in eax, dx ; eeprom delay
dec cx
jns .cmd_loop
; in eax, dx ; eeprom delay
mov al , ( 1 shl BIT_93C46_EEM1 ) or ( 1 shl BIT_93C46_EECS )
out dx , al
mov cl , 0xf
.read_loop:
shl ebx , 1
mov al , ( 1 shl BIT_93C46_EEM1 ) or ( 1 shl BIT_93C46_EECS ) or ( 1 shl BIT_93C46_EESK )
out dx , al
; in eax, dx ; eeprom delay
in al , dx
and al , ( 1 shl BIT_93C46_EEDO )
jz .dont_set
inc ebx
.dont_set:
mov al , ( 1 shl BIT_93C46_EEM1 ) or ( 1 shl BIT_93C46_EECS )
out dx , al
; in eax, dx ; eeprom delay
dec cl
jns .read_loop
xor al , al
out dx , al
mov ax , bx
pop ebx
ret
; End of code
align 4 ; Place all initialised data here
RTL8139_DEV dd 0
version dd ( 5 shl 16 ) or ( API_VERSION and 0xFFFF )
my_service db 'RTL8139' , 0 ; max 16 chars include zero
devicename db 'Realtek 8139' , 0
hw_ver_array db VER_RTL8139 ; This array is used by the probe routine to find out wich version of the RTL8139 we are working with
db VER_RTL8139A
db VER_RTL8139B
db VER_RTL8139C
db VER_RTL8100
db VER_RTL8139D
db VER_RTL8139CP
db VER_RTL8101
HW_VER_ARRAY_SIZE = $ - hw_ver_array
include_debug_strings ; All data wich FDO uses will be included here
section '.data' data readable writable al ign 16 ; place all uninitialized data place here
RTL8139_LIST rd MAX_RTL8139 ; This list contains all pointers to device structures the driver is handling
