;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; Copyright (C) KolibriOS team 2004-2015. All rights reserved. ;; ;; Distributed under terms of the GNU General Public License ;; ;; ;; ;; RTL8169 driver for KolibriOS ;; ;; ;; ;; Copyright 2007 mike.dld, ;; ;; mike.dld@gmail.com ;; ;; ;; ;; port to net branch by hidnplayr ;; ;; ;; ;; References: ;; ;; r8169.c - linux driver (etherboot project) ;; ;; ;; ;; GNU GENERAL PUBLIC LICENSE ;; ;; Version 2, June 1991 ;; ;; ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; format PE DLL native entry START CURRENT_API = 0x0200 COMPATIBLE_API = 0x0100 API_VERSION = (COMPATIBLE_API shl 16) + CURRENT_API MAX_DEVICES = 16 __DEBUG__ = 1 __DEBUG_LEVEL__ = 2 ; 1 = verbose, 2 = errors only NUM_TX_DESC = 4 NUM_RX_DESC = 4 section '.flat' readable writable executable include '../proc32.inc' include '../struct.inc' include '../macros.inc' include '../fdo.inc' include '../netdrv.inc' REG_MAC0 = 0x0 ; Ethernet hardware address REG_MAR0 = 0x8 ; Multicast filter REG_TxDescStartAddr = 0x20 REG_TxHDescStartAddr = 0x28 REG_FLASH = 0x30 REG_ERSR = 0x36 REG_ChipCmd = 0x37 REG_TxPoll = 0x38 REG_IntrMask = 0x3C REG_IntrStatus = 0x3E REG_TxConfig = 0x40 REG_RxConfig = 0x44 REG_RxMissed = 0x4C REG_Cfg9346 = 0x50 REG_Config0 = 0x51 REG_Config1 = 0x52 REG_Config2 = 0x53 REG_Config3 = 0x54 REG_Config4 = 0x55 REG_Config5 = 0x56 REG_MultiIntr = 0x5C REG_PHYAR = 0x60 REG_TBICSR = 0x64 REG_TBI_ANAR = 0x68 REG_TBI_LPAR = 0x6A REG_PHYstatus = 0x6C REG_RxMaxSize = 0xDA REG_CPlusCmd = 0xE0 REG_RxDescStartAddr = 0xE4 REG_ETThReg = 0xEC REG_FuncEvent = 0xF0 REG_FuncEventMask = 0xF4 REG_FuncPresetState = 0xF8 REG_FuncForceEvent = 0xFC ; InterruptStatusBits ISB_SYSErr = 0x8000 ISB_PCSTimeout = 0x4000 ISB_SWInt = 0x0100 ISB_TxDescUnavail = 0x80 ISB_RxFIFOOver = 0x40 ISB_LinkChg = 0x20 ISB_RxOverflow = 0x10 ISB_TxErr = 0x08 ISB_TxOK = 0x04 ISB_RxErr = 0x02 ISB_RxOK = 0x01 ; RxStatusDesc SD_RxRES = 0x00200000 SD_RxCRC = 0x00080000 SD_RxRUNT = 0x00100000 SD_RxRWT = 0x00400000 ; ChipCmdBits CMD_Reset = 0x10 CMD_RxEnb = 0x08 CMD_TxEnb = 0x04 CMD_RxBufEmpty = 0x01 ; Cfg9346Bits CFG_9346_Lock = 0x00 CFG_9346_Unlock = 0xC0 ; rx_mode_bits RXM_AcceptErr = 0x20 RXM_AcceptRunt = 0x10 RXM_AcceptBroadcast = 0x08 RXM_AcceptMulticast = 0x04 RXM_AcceptMyPhys = 0x02 RXM_AcceptAllPhys = 0x01 ; RxConfigBits RXC_FIFOShift = 13 RXC_DMAShift = 8 ; TxConfigBits TXC_InterFrameGapShift = 24 TXC_DMAShift = 8 ; DMA burst value (0-7) is shift this many bits ; PHYstatus PHYS_TBI_Enable = 0x80 PHYS_TxFlowCtrl = 0x40 PHYS_RxFlowCtrl = 0x20 PHYS_1000bpsF = 0x10 PHYS_100bps = 0x08 PHYS_10bps = 0x04 PHYS_LinkStatus = 0x02 PHYS_FullDup = 0x01 ; GIGABIT_PHY_registers PHY_CTRL_REG = 0 PHY_STAT_REG = 1 PHY_AUTO_NEGO_REG = 4 PHY_1000_CTRL_REG = 9 ; GIGABIT_PHY_REG_BIT PHY_Restart_Auto_Nego = 0x0200 PHY_Enable_Auto_Nego = 0x1000 ; PHY_STAT_REG = 1 PHY_Auto_Neco_Comp = 0x0020 ; PHY_AUTO_NEGO_REG = 4 PHY_Cap_10_Half = 0x0020 PHY_Cap_10_Full = 0x0040 PHY_Cap_100_Half = 0x0080 PHY_Cap_100_Full = 0x0100 ; PHY_1000_CTRL_REG = 9 PHY_Cap_1000_Full = 0x0200 PHY_Cap_1000_Half = 0x0100 PHY_Cap_PAUSE = 0x0400 PHY_Cap_ASYM_PAUSE = 0x0800 PHY_Cap_Null = 0x0 ; _MediaType MT_10_Half = 0x01 MT_10_Full = 0x02 MT_100_Half = 0x04 MT_100_Full = 0x08 MT_1000_Full = 0x10 ; _TBICSRBit TBI_LinkOK = 0x02000000 ; _DescStatusBit DSB_OWNbit = 0x80000000 DSB_EORbit = 0x40000000 DSB_FSbit = 0x20000000 DSB_LSbit = 0x10000000 RX_BUF_SIZE = 1514 ; Rx Buffer size ; max supported gigabit ethernet frame size -- must be at least (dev->mtu+14+4) MAX_ETH_FRAME_SIZE = 1514 TX_FIFO_THRESH = 256 ; In bytes RX_FIFO_THRESH = 7 ; 7 means NO threshold, Rx buffer level before first PCI xfer RX_DMA_BURST = 7 ; Maximum PCI burst, '6' is 1024 TX_DMA_BURST = 7 ; Maximum PCI burst, '6' is 1024 ETTh = 0x3F ; 0x3F means NO threshold EarlyTxThld = 0x3F ; 0x3F means NO early transmit RxPacketMaxSize = 0x0800 ; Maximum size supported is 16K-1 InterFrameGap = 0x03 ; 3 means InterFrameGap = the shortest one HZ = 1000 RTL_MIN_IO_SIZE = 0x80 TX_TIMEOUT = (6*HZ) TIMER_EXPIRE_TIME = 100 ETH_HDR_LEN = 14 DEFAULT_MTU = 1500 DEFAULT_RX_BUF_LEN = 1514 ;ifdef JUMBO_FRAME_SUPPORT ; MAX_JUMBO_FRAME_MTU = 10000 ; MAX_RX_SKBDATA_SIZE = (MAX_JUMBO_FRAME_MTU + ETH_HDR_LEN ) ;else MAX_RX_SKBDATA_SIZE = 1600 ;end if MCFG_METHOD_01 = 0x01 MCFG_METHOD_02 = 0x02 MCFG_METHOD_03 = 0x03 MCFG_METHOD_04 = 0x04 MCFG_METHOD_05 = 0x05 MCFG_METHOD_11 = 0x0b MCFG_METHOD_12 = 0x0c MCFG_METHOD_13 = 0x0d MCFG_METHOD_14 = 0x0e MCFG_METHOD_15 = 0x0f PCFG_METHOD_1 = 0x01 ; PHY Reg 0x03 bit0-3 == 0x0000 PCFG_METHOD_2 = 0x02 ; PHY Reg 0x03 bit0-3 == 0x0001 PCFG_METHOD_3 = 0x03 ; PHY Reg 0x03 bit0-3 == 0x0002 struct tx_desc status dd ? vlan_tag dd ? buf_addr dq ? ends tx_desc.buf_soft_addr = NUM_TX_DESC*sizeof.tx_desc struct rx_desc status dd ? vlan_tag dd ? buf_addr dq ? ends rx_desc.buf_soft_addr = NUM_RX_DESC*sizeof.rx_desc struct device ETH_DEVICE io_addr dd ? pci_bus dd ? pci_dev dd ? irq_line db ? rb 3 ; align 4 mmio_addr dd ? ; memory map physical address pcfg dd ? mcfg dd ? cur_rx dd ? ; Index into the Rx descriptor buffer of next Rx pkt cur_tx dd ? ; Index into the Tx descriptor buffer of next Rx pkt last_tx dd ? mac_version dd ? rb 0x100-($ and 0xff) ; align 256 tx_ring rb NUM_TX_DESC * sizeof.tx_desc * 2 rb 0x100-($ and 0xff) ; align 256 rx_ring rb NUM_RX_DESC * sizeof.rx_desc * 2 ends intr_mask = ISB_LinkChg or ISB_RxOverflow or ISB_RxFIFOOver or ISB_TxErr or ISB_TxOK or ISB_RxErr or ISB_RxOK rx_config = (RX_FIFO_THRESH shl RXC_FIFOShift) or (RX_DMA_BURST shl RXC_DMAShift) or 0x0000000E macro udelay msec { push esi ecx mov esi, msec invoke Sleep pop ecx esi } macro WRITE_GMII_REG RegAddr, value { set_io [ebx + device.io_addr], REG_PHYAR if value eq ax and eax, 0x0000ffff or eax, 0x80000000 + (RegAddr shl 16) else mov eax, 0x80000000 + (RegAddr shl 16) + value end if out dx, eax call PHY_WAIT_WRITE } macro READ_GMII_REG RegAddr { local .error, .done set_io [ebx + device.io_addr], REG_PHYAR mov eax, RegAddr shl 16 out dx, eax call PHY_WAIT_READ jz .error in eax, dx and eax, 0xFFFF jmp .done .error: or eax, -1 .done: } align 4 PHY_WAIT_READ: ; io addr must already be set to REG_PHYAR udelay 1 ;;;1000 push ecx mov ecx, 2000 ; Check if the RTL8169 has completed writing/reading to the specified MII register @@: in eax, dx test eax, 0x80000000 jnz .exit udelay 1 ;;;100 loop @b .exit: pop ecx ret align 4 PHY_WAIT_WRITE: ; io addr must already be set to REG_PHYAR udelay 1 ;;;1000 push ecx mov ecx, 2000 ; Check if the RTL8169 has completed writing/reading to the specified MII register @@: in eax, dx test eax, 0x80000000 jz .exit udelay 1 ;;;100 loop @b .exit: pop ecx ret ;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; proc START ;; ;; ;; ;; (standard driver proc) ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;; proc START c, reason:dword, cmdline:dword cmp [reason], DRV_ENTRY jne .fail DEBUGF 2,"Loading driver\n" invoke RegService, my_service, service_proc ret .fail: xor eax, eax ret endp ;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; proc SERVICE_PROC ;; ;; ;; ;; (standard driver proc) ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;; proc service_proc stdcall, ioctl:dword mov edx, [ioctl] mov eax, [edx + IOCTL.io_code] ;------------------------------------------------------ cmp eax, 0 ;SRV_GETVERSION jne @F cmp [edx + IOCTL.out_size], 4 jb .fail mov eax, [edx + IOCTL.output] mov [eax], dword API_VERSION xor eax, eax ret ;------------------------------------------------------ @@: cmp eax, 1 ;SRV_HOOK jne .fail cmp [edx + IOCTL.inp_size], 3 ; Data input must be at least 3 bytes jb .fail mov eax, [edx + IOCTL.input] cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given jne .fail ; other types arent supported for this card yet ; check if the device is already listed mov esi, device_list mov ecx, [devices] test ecx, ecx jz .firstdevice ; mov eax, [edx + IOCTL.input] ; get the pci bus and device numbers mov ax, [eax+1] ; .nextdevice: mov ebx, [esi] cmp al, byte[ebx + device.pci_bus] jne @f cmp ah, byte[ebx + device.pci_dev] je .find_devicenum ; Device is already loaded, let's find it's device number @@: add esi, 4 loop .nextdevice ; This device doesnt have its own eth_device structure yet, lets create one .firstdevice: cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card jae .fail allocate_and_clear ebx, sizeof.device, .fail ; Allocate memory to put the device structure in ; Fill in the direct call addresses into the struct mov [ebx + device.reset], reset mov [ebx + device.transmit], transmit mov [ebx + device.unload], unload mov [ebx + device.name], my_service ; save the pci bus and device numbers mov eax, [edx + IOCTL.input] movzx ecx, byte[eax+1] mov [ebx + device.pci_bus], ecx movzx ecx, byte[eax+2] mov [ebx + device.pci_dev], ecx ; Now, it's time to find the base io addres of the PCI device stdcall PCI_find_io, [ebx + device.pci_bus], [ebx + device.pci_dev] mov [ebx + device.io_addr], eax ; We've found the io address, find IRQ now invoke PciRead8, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.interrupt_line mov [ebx + device.irq_line], al DEBUGF 2,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\ [ebx + device.pci_dev]:1,[ebx + device.pci_bus]:1,[ebx + device.irq_line]:1,[ebx + device.io_addr]:8 ; Ok, the eth_device structure is ready, let's probe the device ; Because initialization fires IRQ, IRQ handler must be aware of this device mov eax, [devices] ; Add the device structure to our device list mov [device_list + 4*eax], ebx ; (IRQ handler uses this list to find device) inc [devices] ; call probe ; this function will output in eax test eax, eax jnz .err2 ; If an error occured, exit mov [ebx + device.type], NET_TYPE_ETH invoke NetRegDev cmp eax, -1 je .destroy ret ; If the device was already loaded, find the device number and return it in eax .find_devicenum: DEBUGF 2,"Trying to find device number of already registered device\n" invoke NetPtrToNum ; This kernel procedure converts a pointer to device struct in ebx ; into a device number in edi mov eax, edi ; Application wants it in eax instead DEBUGF 2,"Kernel says: %u\n", eax ret ; If an error occured, remove all allocated data and exit (returning -1 in eax) .destroy: ; todo: reset device into virgin state .err2: dec [devices] .err: DEBUGF 2,"removing device structure\n" invoke KernelFree, ebx .fail: or eax, -1 ret ;------------------------------------------------------ endp align 4 unload: ret align 4 init_board: DEBUGF 1,"init_board\n" ; Make the device a bus master invoke PciRead32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command or al, PCI_CMD_MASTER invoke PciWrite32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command, eax ; Soft reset the chip set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], REG_ChipCmd mov al, CMD_Reset out dx, al ; Check that the chip has finished the reset mov ecx, 1000 set_io [ebx + device.io_addr], REG_ChipCmd @@: in al, dx test al, CMD_Reset jz @f udelay 10 loop @b @@: set_io [ebx + device.io_addr], REG_TxConfig in eax, dx mov esi, MAC_VERSION_LIST @@: mov ecx, eax and ecx, dword[esi] cmp ecx, dword[esi+4] je @f add esi, 4*4 jmp @r @@: mov eax, [esi+8] mov [ebx + device.mac_version], eax mov eax, [esi+12] mov [ebx + device.name], eax xor eax, eax ret ;*************************************************************************** ; Function ; probe ; Description ; Searches for an ethernet card, enables it and clears the rx buffer ; If a card was found, it enables the ethernet -> TCPIP link ; Destroyed registers ; eax, ebx, ecx, edx ; ;*************************************************************************** align 4 probe: DEBUGF 1,"probe\n" call init_board call read_mac call PHY_config DEBUGF 1,"Set MAC Reg C+CR Offset 0x82h = 0x01h\n" set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], 0x82 mov al, 0x01 out dx, al cmp [ebx + device.mcfg], MCFG_METHOD_03 jae @f DEBUGF 1,"Set PCI Latency=0x40\n" ; Adjust PCI latency to be at least 64 invoke PciRead8, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.max_latency cmp al, 64 jae @f mov al, 64 invoke PciWrite8, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.max_latency, eax @@: cmp [ebx + device.mcfg], MCFG_METHOD_02 jne @f DEBUGF 1,"Set MAC Reg C+CR Offset 0x82h = 0x01h\n" set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], 0x82 mov al, 0x01 out dx, al DEBUGF 1,"Set PHY Reg 0x0bh = 0x00h\n" WRITE_GMII_REG 0x0b, 0x0000 ; w 0x0b 15 0 0 @@: ; if TBI is not enabled set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], REG_PHYstatus in al, dx test al, PHYS_TBI_Enable jz .tbi_dis READ_GMII_REG PHY_AUTO_NEGO_REG ; enable 10/100 Full/Half Mode, leave PHY_AUTO_NEGO_REG bit4:0 unchanged and eax, 0x0C1F or eax, PHY_Cap_10_Half or PHY_Cap_10_Full or PHY_Cap_100_Half or PHY_Cap_100_Full WRITE_GMII_REG PHY_AUTO_NEGO_REG, ax ; enable 1000 Full Mode WRITE_GMII_REG PHY_1000_CTRL_REG, PHY_Cap_1000_Full or PHY_Cap_1000_Half ; rtl8168 ; Enable auto-negotiation and restart auto-nigotiation WRITE_GMII_REG PHY_CTRL_REG, PHY_Enable_Auto_Nego or PHY_Restart_Auto_Nego udelay 1 ; 100 mov ecx, 200 ; 10000 DEBUGF 1, "Waiting for auto-negotiation to complete\n" ; wait for auto-negotiation process @@: dec ecx jz @f set_io [ebx + device.io_addr], 0 READ_GMII_REG PHY_STAT_REG udelay 1 ; 100 test eax, PHY_Auto_Neco_Comp jz @b set_io [ebx + device.io_addr], REG_PHYstatus in al, dx jmp @f .tbi_dis: udelay 1 ; 100 @@: DEBUGF 1, "auto-negotiation complete\n" ;*************************************************************************** ; Function ; rt8169_reset ; Description ; Place the chip (ie, the ethernet card) into a virgin state ; Destroyed registers ; eax, ebx, ecx, edx ; ;*************************************************************************** align 4 reset: DEBUGF 1,"resetting\n" call init_ring test eax, eax jnz .err call hw_start ; clear packet/byte counters xor eax, eax lea edi, [ebx + device.bytes_tx] mov ecx, 6 rep stosd mov [ebx + device.mtu], 1500 call detect_link DEBUGF 2,"init OK!\n" xor eax, eax ret .err: DEBUGF 2,"failed!\n" or eax, -1 ret align 4 PHY_config: DEBUGF 1,"hw_PHY_config: priv.mcfg=%d, priv.pcfg=%d\n", [ebx + device.mcfg], [ebx + device.pcfg] cmp [ebx + device.mcfg], MCFG_METHOD_04 jne .not_4 set_io [ebx + device.io_addr], 0 ; WRITE_GMII_REG 0x1F, 0x0001 ; WRITE_GMII_REG 0x1b, 0x841e ; WRITE_GMII_REG 0x0e, 0x7bfb ; WRITE_GMII_REG 0x09, 0x273a WRITE_GMII_REG 0x1F, 0x0002 WRITE_GMII_REG 0x01, 0x90D0 WRITE_GMII_REG 0x1F, 0x0000 jmp .exit .not_4: cmp [ebx + device.mcfg], MCFG_METHOD_02 je @f cmp [ebx + device.mcfg], MCFG_METHOD_03 jne .not_2_or_3 @@: set_io [ebx + device.io_addr], 0 WRITE_GMII_REG 0x1F, 0x0001 WRITE_GMII_REG 0x15, 0x1000 WRITE_GMII_REG 0x18, 0x65C7 WRITE_GMII_REG 0x04, 0x0000 WRITE_GMII_REG 0x03, 0x00A1 WRITE_GMII_REG 0x02, 0x0008 WRITE_GMII_REG 0x01, 0x1020 WRITE_GMII_REG 0x00, 0x1000 WRITE_GMII_REG 0x04, 0x0800 WRITE_GMII_REG 0x04, 0x0000 WRITE_GMII_REG 0x04, 0x7000 WRITE_GMII_REG 0x03, 0xFF41 WRITE_GMII_REG 0x02, 0xDE60 WRITE_GMII_REG 0x01, 0x0140 WRITE_GMII_REG 0x00, 0x0077 WRITE_GMII_REG 0x04, 0x7800 WRITE_GMII_REG 0x04, 0x7000 WRITE_GMII_REG 0x04, 0xA000 WRITE_GMII_REG 0x03, 0xDF01 WRITE_GMII_REG 0x02, 0xDF20 WRITE_GMII_REG 0x01, 0xFF95 WRITE_GMII_REG 0x00, 0xFA00 WRITE_GMII_REG 0x04, 0xA800 WRITE_GMII_REG 0x04, 0xA000 WRITE_GMII_REG 0x04, 0xB000 WRITE_GMII_REG 0x03, 0xFF41 WRITE_GMII_REG 0x02, 0xDE20 WRITE_GMII_REG 0x01, 0x0140 WRITE_GMII_REG 0x00, 0x00BB WRITE_GMII_REG 0x04, 0xB800 WRITE_GMII_REG 0x04, 0xB000 WRITE_GMII_REG 0x04, 0xF000 WRITE_GMII_REG 0x03, 0xDF01 WRITE_GMII_REG 0x02, 0xDF20 WRITE_GMII_REG 0x01, 0xFF95 WRITE_GMII_REG 0x00, 0xBF00 WRITE_GMII_REG 0x04, 0xF800 WRITE_GMII_REG 0x04, 0xF000 WRITE_GMII_REG 0x04, 0x0000 WRITE_GMII_REG 0x1F, 0x0000 WRITE_GMII_REG 0x0B, 0x0000 jmp .exit .not_2_or_3: DEBUGF 1,"mcfg=%d, discard hw PHY config\n", [ebx + device.mcfg] .exit: ret align 4 set_rx_mode: DEBUGF 1,"set_rx_mode\n" ; IFF_ALLMULTI ; Too many to filter perfectly -- accept all multicasts set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], REG_RxConfig in eax, dx and eax, 0xff7e1880 or eax, rx_config or (RXM_AcceptBroadcast or RXM_AcceptMulticast or RXM_AcceptMyPhys) out dx, eax ; Multicast hash filter set_io [ebx + device.io_addr], REG_MAR0 + 0 or eax, -1 out dx, eax set_io [ebx + device.io_addr], REG_MAR0 + 4 out dx, eax ret align 4 init_ring: DEBUGF 1,"init_ring\n" xor eax, eax mov [ebx + device.cur_rx], eax mov [ebx + device.cur_tx], eax mov [ebx + device.last_tx], eax lea edi, [ebx + device.tx_ring] mov ecx, (NUM_TX_DESC * sizeof.tx_desc) / 4 * 2 rep stosd lea edi, [ebx + device.rx_ring] mov ecx, (NUM_RX_DESC * sizeof.rx_desc) / 4 rep stosd lea edi, [ebx + device.rx_ring] mov ecx, NUM_RX_DESC .loop: push ecx invoke NetAlloc, RX_BUF_SIZE+NET_BUFF.data test eax, eax jz .err mov dword [edi + rx_desc.buf_soft_addr], eax invoke GetPhysAddr add eax, NET_BUFF.data mov dword [edi + rx_desc.buf_addr], eax mov [edi + rx_desc.status], DSB_OWNbit or RX_BUF_SIZE add edi, sizeof.rx_desc pop ecx dec ecx jnz .loop or [edi - sizeof.rx_desc + rx_desc.status], DSB_EORbit xor eax, eax ret .err: pop eax or eax, -1 ret align 4 hw_start: DEBUGF 1,"hw_start\n" ; attach int handler movzx eax, [ebx + device.irq_line] DEBUGF 1,"Attaching int handler to irq %x\n", eax:1 invoke AttachIntHandler, eax, int_handler, ebx test eax, eax jnz @f DEBUGF 2,"Could not attach int handler!\n" or eax, -1 ret @@: ; Soft reset the chip set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], REG_ChipCmd mov al, CMD_Reset out dx, al DEBUGF 1,"Waiting for chip to reset... " ; Check that the chip has finished the reset mov ecx, 1000 set_io [ebx + device.io_addr], REG_ChipCmd @@: in al, dx test al, CMD_Reset jz @f udelay 10 loop @b @@: DEBUGF 1,"done!\n" set_io [ebx + device.io_addr], REG_Cfg9346 mov al, CFG_9346_Unlock out dx, al set_io [ebx + device.io_addr], REG_ChipCmd mov al, CMD_TxEnb or CMD_RxEnb out dx, al set_io [ebx + device.io_addr], REG_ETThReg mov al, ETTh out dx, al ; For gigabit rtl8169 set_io [ebx + device.io_addr], REG_RxMaxSize mov ax, RxPacketMaxSize out dx, ax ; Set Rx Config register set_io [ebx + device.io_addr], REG_RxConfig in ax, dx and eax, 0xff7e1880 or eax, rx_config out dx, eax ; Set DMA burst size and Interframe Gap Time set_io [ebx + device.io_addr], REG_TxConfig mov eax, (TX_DMA_BURST shl TXC_DMAShift) or (InterFrameGap shl TXC_InterFrameGapShift) out dx, eax set_io [ebx + device.io_addr], REG_CPlusCmd in ax, dx out dx, ax in ax, dx or ax, 1 shl 3 cmp [ebx + device.mcfg], MCFG_METHOD_02 jne @f cmp [ebx + device.mcfg], MCFG_METHOD_03 jne @f or ax,1 shl 14 DEBUGF 1,"Set MAC Reg C+CR Offset 0xE0: bit-3 and bit-14\n" jmp .set @@: DEBUGF 1,"Set MAC Reg C+CR Offset 0xE0: bit-3\n" .set: set_io [ebx + device.io_addr], REG_CPlusCmd out dx, ax set_io [ebx + device.io_addr], 0xE2 ; mov ax, 0x1517 ; out dx, ax ; mov ax, 0x152a ; out dx, ax ; mov ax, 0x282a ; out dx, ax xor ax, ax out dx, ax xor eax, eax mov [ebx + device.cur_rx], eax lea eax, [ebx + device.tx_ring] invoke GetPhysAddr set_io [ebx + device.io_addr], REG_TxDescStartAddr out dx, eax set_io [ebx + device.io_addr], REG_TxDescStartAddr + 4 xor eax, eax out dx, eax lea eax, [ebx + device.rx_ring] invoke GetPhysAddr set_io [ebx + device.io_addr], REG_RxDescStartAddr out dx, eax xor eax, eax set_io [ebx + device.io_addr], REG_RxDescStartAddr + 4 out dx, eax set_io [ebx + device.io_addr], REG_Cfg9346 mov al, CFG_9346_Lock out dx, al udelay 10 xor eax, eax set_io [ebx + device.io_addr], REG_RxMissed out dx, eax call set_rx_mode set_io [ebx + device.io_addr], 0 ; no early-rx interrupts set_io [ebx + device.io_addr], REG_MultiIntr in ax, dx and ax, 0xF000 out dx, ax ; set interrupt mask set_io [ebx + device.io_addr], REG_IntrMask mov ax, intr_mask out dx, ax xor eax, eax ret align 4 read_mac: set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], REG_MAC0 xor ecx, ecx lea edi, [ebx + device.mac] mov ecx, 6 ; Get MAC address. FIXME: read EEPROM @@: in al, dx stosb inc edx loop @r DEBUGF 1,"MAC = %x-%x-%x-%x-%x-%x\n",\ [ebx + device.mac+0]:2,[ebx + device.mac+1]:2,[ebx + device.mac+2]:2,[ebx + device.mac+3]:2,[ebx + device.mac+4]:2,[ebx + device.mac+5]:2 ret align 4 write_mac: ret 6 ;*************************************************************************** ; Function ; transmit ; Description ; Transmits a packet of data via the ethernet card ; ; Destroyed registers ; eax, edx, esi, edi ; ;*************************************************************************** proc transmit stdcall bufferptr pushf cli mov esi, [bufferptr] DEBUGF 1,"Transmitting packet, buffer:%x, size:%u\n", [bufferptr], [esi + NET_BUFF.length] lea eax, [esi + NET_BUFF.data] DEBUGF 1,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\ [eax+00]:2,[eax+01]:2,[eax+02]:2,[eax+03]:2,[eax+04]:2,[eax+05]:2,\ [eax+06]:2,[eax+07]:2,[eax+08]:2,[eax+09]:2,[eax+10]:2,[eax+11]:2,\ [eax+13]:2,[eax+12]:2 cmp [esi + NET_BUFF.length], 1514 ja .fail cmp [esi + NET_BUFF.length], 60 jb .fail ;---------------------------------- ; Find currentTX descriptor address mov eax, sizeof.tx_desc mul [ebx + device.cur_tx] lea esi, [ebx + device.tx_ring + eax] DEBUGF 1,"Using TX desc: %x\n", esi ;---------------------------------- ; Check if the descriptor is in use test [esi + tx_desc.status], DSB_OWNbit jnz .desc ;--------------------------- ; Program the packet pointer mov eax, [bufferptr] mov ecx, [eax + NET_BUFF.length] mov [esi + tx_desc.buf_soft_addr], eax add eax, [eax + NET_BUFF.offset] invoke GetPhysAddr mov dword [esi + tx_desc.buf_addr], eax ;------------------------ ; Program the packet size mov eax, ecx or eax, DSB_OWNbit or DSB_FSbit or DSB_LSbit cmp [ebx + device.cur_tx], NUM_TX_DESC - 1 jne @f or eax, DSB_EORbit @@: mov [esi + tx_desc.status], eax ;----------------------------------------- ; Set the polling bit (start transmission) set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], REG_TxPoll mov al, 0x40 ; set polling bit out dx, al ;----------------------- ; Update TX descriptor inc [ebx + device.cur_tx] and [ebx + device.cur_tx], NUM_TX_DESC - 1 ;------------- ; Update stats inc [ebx + device.packets_tx] add dword [ebx + device.bytes_tx], ecx adc dword [ebx + device.bytes_tx + 4], 0 popf xor eax, eax ret .desc: DEBUGF 2,"Descriptor is still in use!\n" .fail: DEBUGF 2,"Transmit failed\n" invoke NetFree, [bufferptr] popf or eax, -1 ret endp ;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; Interrupt handler ;; ;; ;; ;;;;;;;;;;;;;;;;;;;;;;; align 4 int_handler: push ebx esi edi DEBUGF 1,"INT\n" ; find pointer of device wich made IRQ occur mov ecx, [devices] test ecx, ecx jz .nothing mov esi, device_list .nextdevice: mov ebx, [esi] set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], REG_IntrStatus in ax, dx out dx, ax ; ACK all interrupts cmp ax, 0xffff ; if so, hardware is no longer present je .nothing test ax, ax jnz .got_it .continue: add esi, 4 dec ecx jnz .nextdevice .nothing: pop edi esi ebx xor eax, eax ret ; If no device was found, abort (The irq was probably for a device, not registered to this driver) .got_it: DEBUGF 1,"Device: %x Status: %x\n", ebx, ax ;-------- ; Receive test ax, ISB_RxOK jz .no_rx push ax push ebx .check_more: pop ebx mov eax, sizeof.rx_desc mul [ebx + device.cur_rx] lea esi, [ebx + device.rx_ring + eax] DEBUGF 1,"RxDesc.status = 0x%x\n", [esi + rx_desc.status] mov ecx, [esi + rx_desc.status] test ecx, DSB_OWNbit ;;; jnz .rx_return DEBUGF 1,"cur_rx = %u\n", [ebx + device.cur_rx] test ecx, SD_RxRES jnz .rx_return ;;;;; RX error! push ebx push .check_more and ecx, 0x00001FFF add ecx, -4 ; we dont need CRC DEBUGF 1,"data length = %u\n", ecx mov eax, [esi + rx_desc.buf_soft_addr] push eax mov [eax + NET_BUFF.length], ecx mov [eax + NET_BUFF.device], ebx mov [eax + NET_BUFF.offset], NET_BUFF.data ;------------- ; Update stats add dword [ebx + device.bytes_rx], eax adc dword [ebx + device.bytes_rx + 4], 0 inc [ebx + device.packets_rx] ;---------------------- ; Allocate a new buffer invoke NetAlloc, RX_BUF_SIZE+NET_BUFF.data mov [esi + rx_desc.buf_soft_addr], eax invoke GetPhysAddr add eax, NET_BUFF.data mov dword [esi + rx_desc.buf_addr], eax ;--------------- ; re set OWN bit mov eax, DSB_OWNbit or RX_BUF_SIZE cmp [ebx + device.cur_rx], NUM_RX_DESC - 1 jne @f or eax, DSB_EORbit @@: mov [esi + rx_desc.status], eax ;-------------- ; Update rx ptr inc [ebx + device.cur_rx] and [ebx + device.cur_rx], NUM_RX_DESC - 1 jmp [EthInput] .rx_return: pop ax .no_rx: ;----------------- ; Transmit cleanup test ax, ISB_TxOK or ISB_TxErr or ISB_TxDescUnavail jz .no_tx push ax DEBUGF 1,"TX done!\n" mov ecx, NUM_TX_DESC lea esi, [ebx + device.tx_ring] .txloop: cmp dword [esi + tx_desc.buf_soft_addr], 0 jz .maybenext test [esi + tx_desc.status], DSB_OWNbit jnz .maybenext push ecx DEBUGF 1,"Freeing up TX desc: %x\n", esi invoke NetFree, [esi + tx_desc.buf_soft_addr] pop ecx and dword [esi + tx_desc.buf_soft_addr], 0 .maybenext: add esi, sizeof.tx_desc dec ecx jnz .txloop pop ax .no_tx: test ax, ISB_LinkChg jz .no_linkchange DEBUGF 2, "Link change detected\n" call detect_link .no_linkchange: pop edi esi ebx xor eax, eax inc eax ret align 4 detect_link: set_io [ebx + device.io_addr], 0 ; set_io [ebx + device.io_addr], REG_TBICSR ; in eax, dx ; test eax, TBI_LinkOK ; jz .down ; mov [ebx + device.state], ETH_LINK_UNKNOWN ; invoke NetLinkChanged ; ret set_io [ebx + device.io_addr], REG_PHYstatus in al, dx test al, PHYS_LinkStatus jz .down DEBUGF 2, "Link is up, phystatus=0x%x\n", al xor ecx, ecx test al, PHYS_10bps jz @f or cl, ETH_LINK_10M @@: test al, PHYS_100bps jz @f or cl, ETH_LINK_100M @@: test al, PHYS_1000bpsF jz @f or cl, ETH_LINK_1G ;or ETH_LINK_FD @@: test al, PHYS_FullDup jz @f or cl, ETH_LINK_FD @@: mov [ebx + device.state], ecx invoke NetLinkChanged ret .down: DEBUGF 2, "Link is down\n" mov [ebx + device.state], ETH_LINK_DOWN invoke NetLinkChanged ret ; End of code data fixups end data include '../peimport.inc' my_service db 'RTL8169',0 ; max 16 chars include zero include_debug_strings ; All data wich FDO uses will be included here MAC_VERSION_LIST: ; 8168EP family. dd 0x7cf00000, 0x50200000, 51, name_49 dd 0x7cf00000, 0x50100000, 50, name_49 dd 0x7cf00000, 0x50000000, 49, name_49 ; 8168H family. dd 0x7cf00000, 0x54100000, 46, name_45 dd 0x7cf00000, 0x54000000, 45, name_45 ; 8168G family. dd 0x7cf00000, 0x5c800000, 44, name_44 dd 0x7cf00000, 0x50900000, 42, name_40 dd 0x7cf00000, 0x4c100000, 41, name_40 dd 0x7cf00000, 0x4c000000, 40, name_40 ; 8168F family. dd 0x7c800000, 0x48800000, 38, name_38 dd 0x7cf00000, 0x48100000, 36, name_35 dd 0x7cf00000, 0x48000000, 35, name_35 ; 8168E family. dd 0x7c800000, 0x2c800000, 34, name_34 dd 0x7cf00000, 0x2c200000, 33, name_32 dd 0x7cf00000, 0x2c100000, 32, name_32 dd 0x7c800000, 0x2c000000, 33, name_32 ; 8168D family. dd 0x7cf00000, 0x28300000, 26, name_25 dd 0x7cf00000, 0x28100000, 25, name_25 dd 0x7c800000, 0x28000000, 26, name_25 ; 8168DP family. dd 0x7cf00000, 0x28800000, 27, name_27 dd 0x7cf00000, 0x28a00000, 28, name_27 ; 8168C family. dd 0x7cf00000, 0x3cb00000, 24, name_18 dd 0x7cf00000, 0x3c900000, 23, name_18 dd 0x7cf00000, 0x3c800000, 18, name_18 dd 0x7c800000, 0x3c800000, 24, name_18 dd 0x7cf00000, 0x3c000000, 19, name_19 dd 0x7cf00000, 0x3c200000, 20, name_19 dd 0x7cf00000, 0x3c300000, 21, name_19 dd 0x7cf00000, 0x3c400000, 22, name_19 dd 0x7c800000, 0x3c000000, 22, name_19 ; 8168B family. dd 0x7cf00000, 0x38000000, 12, name_11 dd 0x7cf00000, 0x38500000, 17, name_10 dd 0x7c800000, 0x38000000, 17, name_10 dd 0x7c800000, 0x30000000, 11, name_11 ; 8101 family. dd 0x7cf00000, 0x34a00000, 09, name_07 dd 0x7cf00000, 0x24a00000, 09, name_07 dd 0x7cf00000, 0x34900000, 08, name_07 dd 0x7cf00000, 0x24900000, 08, name_07 dd 0x7cf00000, 0x34800000, 07, name_07 dd 0x7cf00000, 0x24800000, 07, name_07 dd 0x7cf00000, 0x34000000, 13, name_10 dd 0x7cf00000, 0x34300000, 10, name_10 dd 0x7cf00000, 0x34200000, 16, name_11 dd 0x7c800000, 0x34800000, 09, name_07 dd 0x7c800000, 0x24800000, 09, name_07 dd 0x7c800000, 0x34000000, 16, name_11 dd 0xfc800000, 0x38800000, 15, name_14 dd 0xfc800000, 0x30800000, 14, name_14 ; 8110 family. dd 0xfc800000, 0x98000000, 06, name_05 dd 0xfc800000, 0x18000000, 05, name_05 dd 0xfc800000, 0x10000000, 04, name_04 dd 0xfc800000, 0x04000000, 03, name_03 dd 0xfc800000, 0x00800000, 02, name_02 dd 0xfc800000, 0x00000000, 01, name_01 ; Catch-all dd 0x00000000, 0x00000000, 0, name_unknown ; PCI-devices name_01 db "RTL8169",0 name_02 db "RTL8169s",0 name_03 db "RTL8110s",0 name_04 db "RTL8169sb/8110sb",0 name_05 db "RTL8169sc/8110sc",0 ;name_06 db "RTL8169sc/8110sc",0 ; PCI-E devices name_07 db "RTL8102e",0 ;name_08 db "RTL8102e",0 ;name_09 db "RTL8102e",0 name_10 db "RTL8101e",0 name_11 db "RTL8168b/8111b",0 ;name_12 db "RTL8168b/8111b",0 ;name_13 db "RTL8101e",0 name_14 db "RTL8100e",0 ;name_15 db "RTL8100e",0 ;name_16 db "RTL8168b/8111b",0 ;name_17 db "RTL8101e",0 name_18 db "RTL8168cp/8111cp",0 name_19 db "RTL8168c/8111c",0 ;name_20 db "RTL8168c/8111c",0 ;name_21 db "RTL8168c/8111c",0 ;name_22 db "RTL8168c/8111c",0 ;name_23 db "RTL8168cp/8111cp",0 ;name_24 db "RTL8168cp/8111cp",0 name_25 db "RTL8168d/8111d",0 ;name_26 db "RTL8168d/8111d",0 name_27 db "RTL8168dp/8111dp",0 ;name_28 db "RTL8168dp/8111dp",0 name_29 db "RTL8105e",0 ;name_30 db "RTL8105e",0 ;name_31 db "RTL8168dp/8111dp",0 name_32 db "RTL8168e/8111e",0 ;name_33 db "RTL8168e/8111e",0 name_34 db "RTL8168evl/8111evl",0 name_35 db "RTL8168f/8111f",0 ;name_36 db "RTL8168f/8111f",0 name_37 db "RTL8402",0 name_38 db "RTL8411",0 name_39 db "RTL8106e",0 name_40 db "RTL8168g/8111g",0 ;name_41 db "RTL8168g/8111g",0 ;name_42 db "RTL8168g/8111g",0 ;name_43 db "RTL8106e",0 name_44 db "RTL8411",0 name_45 db "RTL8168h/8111h",0 ;name_46 db "RTL8168h/8111h",0 name_47 db "RTL8107e",0 ;name_48 db "RTL8107e",0 name_49 db "RTL8168ep/8111ep",0 ;name_50 db "RTL8168ep/8111ep",0 ;name_51 db "RTL8168ep/8111ep",0 name_unknown db "unknown RTL8169 clone",0 align 4 devices dd 0 device_list rd MAX_DEVICES ; This list contains all pointers to device structures the driver is handling