kolibrios-fun/drivers/ethernet/ar81xx.asm
hidnplayr 07efb9321b Add chip type detection. Only QCA816x/7x supported so far.
git-svn-id: svn://kolibrios.org@7827 a494cfbc-eb01-0410-851d-a64ba20cac60
2020-04-27 18:47:33 +00:00

1803 lines
50 KiB
NASM

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Copyright (C) KolibriOS team 2018-2020. All rights reserved. ;;
;; Distributed under terms of the GNU General Public License ;;
;; ;;
;; AR81XX driver for KolibriOS ;;
;; ;;
;; based on alx driver from TI-OpenLink ;;
;; ;;
;; Written by hidnplayr (hidnplayr@gmail.com) ;;
;; ;;
;; Thanks to: floppy121 for kindly providing me with the hardware ;;
;; that made the development of this driver possible. ;;
;; ;;
;; GNU GENERAL PUBLIC LICENSE ;;
;; Version 2, June 1991 ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
format PE DLL native
entry START
CURRENT_API = 0x0200
COMPATIBLE_API = 0x0100
API_VERSION = (COMPATIBLE_API shl 16) + CURRENT_API
MAX_DEVICES = 16
__DEBUG__ = 1
__DEBUG_LEVEL__ = 2
TX_RING_SIZE = 128 ; RING sizes must be a power of 2
RX_RING_SIZE = 128
RX_BUFFER_SIZE = 1536
SMB_TIMER = 400
IMT = 200
ITH_TPD = TX_RING_SIZE / 3
section '.flat' readable writable executable
include '../proc32.inc'
include '../struct.inc'
include '../macros.inc'
include '../fdo.inc'
include '../netdrv.inc'
include 'ar81xx.inc'
; Transmit Packet Descriptor
struct alx_tpd
length dw ?
vlan_tag dw ?
word1 dd ?
addr_l dd ?
addr_h dd ?
ends
; Receive Return Descriptor
struct alx_rrd
word0 dd ? ; IP payload cksum + number of RFDs + start index of RFD-ring
rss_hash dd ?
word2 dd ? ; VLAN tag + Protocol ID + RSS Q num + RSS Hash algorithm
word3 dd ? ; Packet length + status
ends
; Receive Free Descriptor
struct alx_rfd
addr_l dd ?
addr_h dd ?
ends
struct device ETH_DEVICE
io_addr dd ?
pci_bus dd ?
pci_dev dd ?
pci_vid dw ? ; Vendor ID
pci_did dw ? ; Device ID
irq_line dd ?
pci_rev dd ?
chip_rev dd ?
mmio_addr dd ?
; dma_chnl dd ?
max_dma_chnl dd ?
int_mask dd ?
rx_ctrl dd ?
rxq_read_idx dd ?
rxq_write_idx dd ?
; rxq_rrd_read_idx dd ?
txq_read_idx dd ?
txq_write_idx dd ?
rb 0x100 - ($ and 0xff) ; align 256
tpd_ring rb ((TX_RING_SIZE*sizeof.alx_tpd+16) and 0xfffffff0)
rrd_ring rb ((RX_RING_SIZE*sizeof.alx_rrd+16) and 0xfffffff0)
rfd_ring rb ((RX_RING_SIZE*sizeof.alx_rfd+16) and 0xfffffff0)
tpd_ring_virt rd TX_RING_SIZE
rfd_ring_virt rd RX_RING_SIZE
ends
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; proc START ;;
;; ;;
;; (standard driver proc) ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
proc START c, reason:dword, cmdline:dword
cmp [reason], DRV_ENTRY
jne .fail
DEBUGF 2,"Loading driver\n"
invoke RegService, my_service, service_proc
ret
.fail:
xor eax, eax
ret
endp
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; proc SERVICE_PROC ;;
;; ;;
;; (standard driver proc) ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
proc service_proc stdcall, ioctl:dword
mov edx, [ioctl]
mov eax, [edx + IOCTL.io_code]
;------------------------------------------------------
cmp eax, 0 ;SRV_GETVERSION
jne @F
cmp [edx + IOCTL.out_size], 4
jb .fail
mov eax, [edx + IOCTL.output]
mov [eax], dword API_VERSION
xor eax, eax
ret
;------------------------------------------------------
@@:
cmp eax, 1 ;SRV_HOOK
jne .fail
cmp [edx + IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
jb .fail
mov eax, [edx + IOCTL.input]
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
jne .fail ; other types arent supported for this card yet
; check if the device is already listed
mov esi, device_list
mov ecx, [devices]
test ecx, ecx
jz .firstdevice
; mov eax, [edx + IOCTL.input] ; get the pci bus and device numbers
mov ax , [eax+1] ;
.nextdevice:
mov ebx, [esi]
cmp al, byte[ebx + device.pci_bus]
jne @f
cmp ah, byte[ebx + device.pci_dev]
je .find_devicenum ; Device is already loaded, let's find it's device number
@@:
add esi, 4
loop .nextdevice
; This device doesnt have its own eth_device structure yet, lets create one
.firstdevice:
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
jae .fail
allocate_and_clear ebx, sizeof.device, .fail ; Allocate the buffer for device structure
; Fill in the direct call addresses into the struct
mov [ebx + device.reset], reset
mov [ebx + device.transmit], transmit
mov [ebx + device.unload], unload
mov [ebx + device.name], my_service
; save the pci bus and device numbers
mov eax, [edx + IOCTL.input]
movzx ecx, byte[eax+1]
mov [ebx + device.pci_bus], ecx
movzx ecx, byte[eax+2]
mov [ebx + device.pci_dev], ecx
; Now, it's time to find the base mmio addres of the PCI device
stdcall PCI_find_mmio, [ebx + device.pci_bus], [ebx + device.pci_dev] ; returns in eax
test eax, eax
jz .destroy
; Create virtual mapping of the physical memory
invoke MapIoMem, eax, 10000h, PG_SW+PG_NOCACHE
mov [ebx + device.mmio_addr], eax
; We've found the mmio address, find IRQ now
invoke PciRead8, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.interrupt_line
and eax, 0xff
mov [ebx + device.irq_line], eax
DEBUGF 1,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\
[ebx + device.pci_dev]:1, [ebx + device.pci_bus]:1, [ebx + device.irq_line]:1, [ebx + device.mmio_addr]:8
; Ok, the eth_device structure is ready, let's probe the device
mov eax, [devices] ; Add the device structure to our device list
mov [device_list+4*eax], ebx ; (IRQ handler uses this list to find device)
inc [devices] ;
call probe ; this function will output in eax
test eax, eax
jnz .err2
DEBUGF 2,"Initialised OK\n"
mov [ebx + device.type], NET_TYPE_ETH
invoke NetRegDev
cmp eax, -1
je .destroy
ret
; If the device was already loaded, find the device number and return it in eax
.find_devicenum:
DEBUGF 2,"Trying to find device number of already registered device\n"
invoke NetPtrToNum ; This kernel procedure converts a pointer to device struct in ebx
; into a device number in edi
mov eax, edi ; Application wants it in eax instead
DEBUGF 2,"Kernel says: %u\n", eax
ret
; If an error occured, remove all allocated data and exit (returning -1 in eax)
.destroy:
; todo: reset device into virgin state
.err2:
dec [devices]
.err:
invoke KernelFree, ebx
.fail:
DEBUGF 2, "Failed to load\n"
or eax, -1
ret
;------------------------------------------------------
endp
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
;; ;;
;; Actual Hardware dependent code starts here ;;
;; ;;
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
align 4
unload:
; TODO: (in this particular order)
;
; - Stop the device
; - Detach int handler
; - Remove device from local list (device_list)
; - call unregister function in kernel
; - Remove all allocated structures and buffers the card used
or eax, -1
ret
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;
;; probe: enables the device (if it really is AR81XX)
;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
align 4
probe:
DEBUGF 1,"Probing\n"
; Make the device a bus master
invoke PciRead16, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command
or al, PCI_CMD_MASTER + PCI_CMD_MMIO + PCI_CMD_PIO
and ax, not(PCI_CMD_INTX_DISABLE)
invoke PciWrite16, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command, eax
; get device id
invoke PciRead16, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.device_id
mov [ebx + device.pci_did], ax
mov esi, chiplist
.loop:
cmp word[esi+2], ax
je .got_it
add esi, 8
cmp esi, chiplist + 6*8
jbe .loop
DEBUGF 2, "Unknown chip: 0x%x, continuing anyway\n", ax
jmp .done
.got_it:
mov eax, dword[esi+4]
mov [ebx + device.name], eax
DEBUGF 1, "Chip type = %s\n", eax
.done:
; get revision id.
invoke PciRead8, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.revision_id
and eax, 0xff
mov [ebx + device.pci_rev], eax
shr al, ALX_PCI_REVID_SHIFT
mov [ebx + device.chip_rev], eax
DEBUGF 1,"Revision: %u\n", al
;;; call alx_reset_pcie
mov ecx, (ALX_PMCTRL_L0S_EN or ALX_PMCTRL_L1_EN or ALX_PMCTRL_ASPM_FCEN)
call alx_enable_aspm
call alx_reset_phy
call alx_reset_mac
call alx_get_perm_macaddr
align 4
reset:
DEBUGF 1,"Resetting\n"
; alx init_sw
call alx_identify_hw
; mov eax, [ebx + device.max_dma_chnl]
; mov [ebx + device.dma_chnl], eax
mov [ebx + device.int_mask], ALX_ISR_MISC
mov [ebx + device.rx_ctrl], ALX_MAC_CTRL_WOLSPED_SWEN or ALX_MAC_CTRL_MHASH_ALG_HI5B or ALX_MAC_CTRL_BRD_EN or ALX_MAC_CTRL_PCRCE or ALX_MAC_CTRL_CRCE or ALX_MAC_CTRL_RXFC_EN or ALX_MAC_CTRL_TXFC_EN or (7 shl ALX_MAC_CTRL_PRMBLEN_SHIFT)
call alx_alloc_rings
call alx_configure
call alx_request_irq
; attach interrupt handler
mov eax, [ebx + device.irq_line]
DEBUGF 1,"Attaching int handler to irq %x\n", eax:1
invoke AttachIntHandler, eax, int_handler, ebx
test eax, eax
jnz @f
DEBUGF 2,"Could not attach int handler!\n"
or eax, -1
ret
@@:
; Clear old interrupts
mov edi, [ebx + device.mmio_addr]
mov eax, not ALX_ISR_DIS
mov [edi + ALX_ISR], eax
call alx_irq_enable
; Set the mtu, kernel will be able to send now
mov [ebx + device.mtu], 1514
call alx_check_link
DEBUGF 1,"Reset ok\n"
xor eax, eax
ret
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Transmit ;;
;; ;;
;; In: pointer to device structure in ebx ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; alx_start_xmit
;; alx_map_tx_skb
proc transmit stdcall bufferptr
pushf
cli
mov esi, [bufferptr]
DEBUGF 1,"Transmitting packet, buffer:%x, size:%u\n", [bufferptr], [esi + NET_BUFF.length]
lea eax, [esi + NET_BUFF.data]
DEBUGF 1,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\
[eax+00]:2,[eax+01]:2,[eax+02]:2,[eax+03]:2,[eax+04]:2,[eax+05]:2,\
[eax+06]:2,[eax+07]:2,[eax+08]:2,[eax+09]:2,[eax+10]:2,[eax+11]:2,\
[eax+13]:2,[eax+12]:2
cmp [esi + NET_BUFF.length], 1514
ja .fail
cmp [esi + NET_BUFF.length], 60
jb .fail
; Program the descriptor
mov edi, [ebx + device.txq_write_idx]
DEBUGF 1, "Using TPD: %u\n", edi
mov dword[ebx + device.tpd_ring_virt + edi*4], esi
shl edi, 4
lea edi, [ebx + device.tpd_ring + edi]
mov eax, esi
add eax, [esi + NET_BUFF.offset]
invoke GetPhysAddr
mov [edi + alx_tpd.addr_l], eax
mov [edi + alx_tpd.addr_h], 0
mov ecx, [esi + NET_BUFF.length]
mov [edi + alx_tpd.length], cx
mov [edi + alx_tpd.word1], 1 shl TPD_EOP_SHIFT
; Update Producer Index
mov eax, [ebx + device.txq_write_idx]
inc eax
and eax, TX_RING_SIZE - 1
mov [ebx + device.txq_write_idx], eax
mov edi, [ebx + device.mmio_addr]
mov word[edi + ALX_TPD_PRI0_PIDX], ax
; Update stats
inc [ebx + device.packets_tx]
mov eax, [esi + NET_BUFF.length]
add dword[ebx + device.bytes_tx], eax
adc dword[ebx + device.bytes_tx + 4], 0
popf
xor eax, eax
ret
.fail:
DEBUGF 2,"Send failed\n"
invoke NetFree, [bufferptr]
popf
or eax, -1
ret
endp
;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Interrupt handler ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;
align 4
int_handler:
push ebx esi edi
DEBUGF 1,"int\n"
; Find pointer of device wich made IRQ occur
mov ecx, [devices]
test ecx, ecx
jz .nothing
mov esi, device_list
.nextdevice:
mov ebx, [esi]
mov edi, [ebx + device.mmio_addr]
mov eax, [edi + ALX_ISR]
test eax, eax
jnz .got_it
.continue:
add esi, 4
dec ecx
jnz .nextdevice
.nothing:
pop edi esi ebx
xor eax, eax
ret ; If no device was found, abort
; At this point, test for all possible reasons, and handle accordingly
.got_it:
or eax, ALX_ISR_DIS
mov [edi + ALX_ISR], eax ; ACK interrupt
DEBUGF 1,"Device: %x Status: %x\n", ebx, eax
test eax, ALX_ISR_TX_Q0
jz .no_tx
DEBUGF 1,"TX interrupt\n"
pusha
call alx_clean_tx_irq
popa
.no_tx:
test eax, ALX_ISR_RX_Q0
jz .no_rx
DEBUGF 1,"RX interrupt\n"
pusha
call alx_clean_rx_irq
popa
.no_rx:
test eax, ALX_ISR_PHY
jz .no_phy
DEBUGF 1,"PHY interrupt\n"
pusha
; TODO: queue link check and disable this interrupt cause meanwhile??
call alx_check_link
popa
.no_phy:
mov dword[edi + ALX_ISR], 0
pop edi esi ebx
ret
align 16
alx_identify_hw:
cmp [ebx + device.chip_rev], ALX_REV_C0
ja .einval
mov [ebx + device.max_dma_chnl], 2
cmp [ebx + device.chip_rev], ALX_REV_B0
jb @f
mov [ebx + device.max_dma_chnl], 4
@@:
xor eax, eax
ret
.einval:
DEBUGF 1, "Invalid revision 0x%x\n", [ebx + device.chip_rev]
xor eax, eax
dec eax
ret
align 16
alx_clean_tx_irq:
mov eax, [ebx + device.txq_read_idx]
movzx ecx, word[edi + ALX_TPD_PRI0_CIDX]
.loop:
cmp eax, ecx
je .done
DEBUGF 1,"Cleaning TX desc %u buffer 0x%x\n", eax, [ebx + device.tpd_ring_virt + eax*4]
push eax ecx
invoke NetFree, [ebx + device.tpd_ring_virt + eax*4]
pop ecx eax
inc eax
and eax, TX_RING_SIZE-1
jmp .loop
.done:
mov [ebx + device.txq_read_idx], eax
ret
align 16
alx_clean_rx_irq:
mov ecx, [ebx + device.rxq_read_idx]
.loop:
shl ecx, 2
lea esi, [ebx + device.rrd_ring + ecx*4]
test [esi + alx_rrd.word3], 1 shl RRD_UPDATED_SHIFT
jz .done
and [esi + alx_rrd.word3], not(1 shl RRD_UPDATED_SHIFT)
DEBUGF 1,"RRD=%u updated\n", [ebx + device.rxq_read_idx]
mov eax, [esi + alx_rrd.word0]
shr eax, RRD_SI_SHIFT
and eax, RRD_SI_MASK
cmp eax, [ebx + device.rxq_read_idx]
; jne .error
DEBUGF 1,"RFD=%u\n", eax
mov eax, [esi + alx_rrd.word0]
shr eax, RRD_NOR_SHIFT
and eax, RRD_NOR_MASK
cmp eax, 1
; jne .error
mov eax, [esi + alx_rrd.word3]
; shr eax, RRD_PKTLEN_SHIFT
and eax, RRD_PKTLEN_MASK
sub eax, 4 ;;;;;
mov edx, [ebx + device.rfd_ring_virt + ecx]
DEBUGF 1,"Received %u bytes in buffer 0x%x\n", eax, edx
mov [edx + NET_BUFF.length], eax
mov [edx + NET_BUFF.device], ebx
mov [edx + NET_BUFF.offset], NET_BUFF.data
; Update stats
add dword[ebx + device.bytes_rx], eax
adc dword[ebx + device.bytes_rx + 4], 0
inc [ebx + device.packets_rx]
; Allocate new descriptor
push esi ecx edx
invoke NetAlloc, RX_BUFFER_SIZE+NET_BUFF.data
pop edx ecx esi
test eax, eax
; jz .out_of_mem
mov [ebx + device.rfd_ring_virt + ecx], eax
add eax, NET_BUFF.data
invoke GetPhysAddr
mov dword[ebx + device.rfd_ring + ecx*2], eax
push ecx ebx
push .retaddr
push edx
jmp [EthInput]
.retaddr:
pop ebx ecx
shr ecx, 2
inc ecx
and ecx, RX_RING_SIZE-1
jmp .loop
.done:
shr ecx, 2
mov [ebx + device.rxq_read_idx], ecx
; Update producer index
mov esi, [ebx + device.mmio_addr]
mov [esi + ALX_RFD_PIDX], cx
ret
align 16
; ecx = additional bit flags (ALX_PMCTRL_L0S_EN, ALX_PMCTRL_L1_EN, ALX_PMCTRL_ASPM_FCEN)
alx_enable_aspm:
DEBUGF 1,"alx_enable_aspm (0x%x)\n", ecx
mov esi, [ebx + device.mmio_addr]
mov eax, dword[esi + ALX_PMCTRL]
and eax, not(ALX_PMCTRL_LCKDET_TIMER_MASK shl ALX_PMCTRL_LCKDET_TIMER_SHIFT)
or eax, (ALX_PMCTRL_LCKDET_TIMER_DEF shl ALX_PMCTRL_LCKDET_TIMER_SHIFT)
or eax, (ALX_PMCTRL_RCVR_WT_1US or ALX_PMCTRL_L1_CLKSW_EN or ALX_PMCTRL_L1_SRDSRX_PWD)
and eax, not(ALX_PMCTRL_L1REQ_TO_MASK shl ALX_PMCTRL_L1REQ_TO_SHIFT)
or eax, (ALX_PMCTRL_L1REG_TO_DEF shl ALX_PMCTRL_L1REQ_TO_SHIFT)
and eax, not(ALX_PMCTRL_L1_TIMER_MASK shl ALX_PMCTRL_L1_TIMER_SHIFT)
or eax, (ALX_PMCTRL_L1_TIMER_16US shl ALX_PMCTRL_L1_TIMER_SHIFT)
and eax, not(ALX_PMCTRL_L1_SRDS_EN or ALX_PMCTRL_L1_SRDSPLL_EN or ALX_PMCTRL_L1_BUFSRX_EN or ALX_PMCTRL_SADLY_EN or ALX_PMCTRL_HOTRST_WTEN or ALX_PMCTRL_L0S_EN or ALX_PMCTRL_L1_EN or ALX_PMCTRL_ASPM_FCEN or ALX_PMCTRL_TXL1_AFTER_L0S or ALX_PMCTRL_RXL1_AFTER_L0S)
cmp [ebx + device.chip_rev], ALX_REV_A1
ja @f
test [ebx + device.pci_rev], 1
jz @f
or eax, ALX_PMCTRL_L1_SRDS_EN or ALX_PMCTRL_L1_SRDSPLL_EN
@@:
or eax, ecx
mov dword[esi + ALX_PMCTRL], eax
ret
align 16
alx_reset_mac:
DEBUGF 1, "reset mac\n"
; disable all interrupts, RXQ/TXQ
mov esi, [ebx + device.mmio_addr]
mov dword[esi + ALX_MSIX_MASK], 0xffffffff
mov dword[esi + ALX_IMR], 0x0
mov dword[esi + ALX_ISR], ALX_ISR_DIS
call alx_stop_mac
; mac reset workaround
mov dword[esi + ALX_RFD_PIDX], 1
; disable l0s/l1 before mac reset on some chips
cmp [ebx + device.chip_rev], ALX_REV_A1
ja @f
test [ebx + device.pci_rev], 1 ; Card reader function? FIXME: according register definitions, this should be bit 1 ISO 0
jz @f
mov eax, [esi + ALX_PMCTRL]
mov edx, eax
and eax, not(ALX_PMCTRL_L1_EN or ALX_PMCTRL_L0S_EN)
mov [esi + ALX_PMCTRL], eax
@@:
; reset whole mac safely
mov eax, [esi + ALX_MASTER]
or eax, ALX_MASTER_DMA_MAC_RST + ALX_MASTER_OOB_DIS
mov [esi + ALX_MASTER], eax
; make sure it's real idle
push esi ecx edx
xor esi, esi
inc esi
invoke Sleep ; FIXME
pop edx ecx esi
mov ecx, ALX_DMA_MAC_RST_TO
.loop1:
mov eax, dword[esi + ALX_RFD_PIDX]
test eax, eax
jz @f
dec ecx
jnz .loop1
jmp .error
@@:
.loop2:
mov eax, dword[esi + ALX_MASTER]
test eax, ALX_MASTER_DMA_MAC_RST
jz @f
dec ecx
jnz .loop2
jmp .error
@@:
; restore l0s/l1
cmp [ebx + device.chip_rev], ALX_REV_A1
ja @f
test [ebx + device.pci_rev], 1 ; Card reader function? FIXME: according register definitions, this should be bit 1 ISO 0
jz @f
or eax, ALX_MASTER_PCLKSEL_SRDS
mov [esi + ALX_MASTER], eax
mov [esi + ALX_PMCTRL], edx
@@:
call alx_reset_osc
; clear Internal OSC settings, switching OSC by hw itself, disable isolate for rev A devices
mov eax, [esi + ALX_MISC3]
and eax, not (ALX_MISC3_25M_BY_SW)
or eax, ALX_MISC3_25M_NOTO_INTNL
mov [esi + ALX_MISC3], eax
mov eax, [esi + ALX_MISC]
and eax, not (ALX_MISC_INTNLOSC_OPEN)
cmp [ebx + device.chip_rev], ALX_REV_A1
ja @f
and eax, not ALX_MISC_ISO_EN
@@:
mov [esi + ALX_MISC], eax
push esi
xor esi, esi
inc esi
invoke Sleep ;; FIXME: udelay(20);
pop esi
; driver control speed/duplex, hash-alg
mov eax, [ebx + device.rx_ctrl]
mov [esi + ALX_MAC_CTRL], eax
mov eax, dword[esi + ALX_SERDES]
or eax, ALX_SERDES_MACCLK_SLWDWN or ALX_SERDES_PHYCLK_SLWDWN
mov dword[esi + ALX_SERDES], eax
DEBUGF 1, "OK\n"
xor eax, eax
ret
.error:
DEBUGF 1, "error\n"
xor eax, eax
dec eax
ret
align 16
alx_reset_phy:
DEBUGF 1, "Reset phy\n"
mov esi, [ebx + device.mmio_addr]
;; TODO
; set phy interrupt mask
stdcall alx_read_phy_reg, 0, ALX_MII_IER
or eax, ALX_IER_LINK_UP or ALX_IER_LINK_DOWN
stdcall alx_write_phy_reg, 0, ALX_MII_IER , eax
DEBUGF 1, "OK\n"
xor eax, eax
ret
.error:
DEBUGF 1, "error\n"
xor eax, eax
dec eax
ret
;align 16
;alx_enable_osc:
;
; mov esi, [ebx + device.mmio_addr]
;
;; rising edge
; mov eax, dword[esi + ALX_MISC]
; and eax, not ALX_MISC_INTNLOSC_OPEN
; mov dword[esi + ALX_MISC], eax
; or eax, ALX_MISC_INTNLOSC_OPEN
; mov dword[esi + ALX_MISC], eax
;
; ret
align 16
alx_reset_osc:
mov esi, [ebx + device.mmio_addr]
; clear Internal OSC settings, switching OSC by hw itself
mov eax, dword[esi + ALX_MISC3]
and eax, not ALX_MISC3_25M_BY_SW
or eax, ALX_MISC3_25M_NOTO_INTNL
mov dword[esi + ALX_MISC3], eax
; clk from chipset may be unstable 1s after de-assert of
; PERST, driver need re-calibrate before enter Sleep for WoL
mov eax, dword[esi + ALX_MISC]
cmp [ebx + device.chip_rev], ALX_REV_B0
jb .rev_a
; restore over current protection def-val, this val could be reset by MAC-RST
and eax, not (ALX_MISC_PSW_OCP_MASK shl ALX_MISC_PSW_OCP_SHIFT)
or eax, ALX_MISC_PSW_OCP_DEF shl ALX_MISC_PSW_OCP_SHIFT
; a 0->1 change will update the internal val of osc
and eax, not ALX_MISC_INTNLOSC_OPEN
mov dword[esi + ALX_MISC], eax
or eax, ALX_MISC_INTNLOSC_OPEN
mov dword[esi + ALX_MISC], eax
; hw will automatically dis OSC after cab
mov eax, dword[esi + ALX_MSIC2]
and eax, not ALX_MSIC2_CALB_START
mov dword[esi + ALX_MSIC2], eax
or eax, ALX_MSIC2_CALB_START
mov dword[esi + ALX_MSIC2], eax
push esi ecx
xor esi, esi
inc esi
invoke Sleep ;; FIXME: udelay(20)
pop ecx esi
ret
.rev_a:
; disable isolate for rev A devices
and eax, not ( ALX_MISC_ISO_EN)
or eax, ALX_MISC_INTNLOSC_OPEN
mov dword[esi + ALX_MISC], eax
and eax, not ALX_MISC_INTNLOSC_OPEN
mov dword[esi + ALX_MISC], eax
push esi ecx
xor esi, esi
inc esi
invoke Sleep ;; FIXME: udelay(20)
pop ecx esi
ret
align 16
alx_read_macaddr:
mov esi, [ebx + device.mmio_addr]
mov eax, dword[esi + ALX_STAD0]
bswap eax
mov dword[ebx + device.mac + 2], eax
mov ax, word[esi + ALX_STAD1]
xchg al, ah
mov word[ebx + device.mac], ax
DEBUGF 1,"MAC = %x-%x-%x-%x-%x-%x\n",\
[ebx + device.mac+0]:2, [ebx + device.mac+1]:2, [ebx + device.mac+2]:2, [ebx + device.mac+3]:2, [ebx + device.mac+4]:2, [ebx + device.mac+5]:2
; check if it is a valid MAC
cmp dword[ebx + device.mac], 0x0
jne @f
cmp word[ebx + device.mac + 4], 0x0
je .invalid
@@:
cmp dword[ebx + device.mac], 0xffffffff
jne @f
cmp word[ebx + device.mac + 4], 0xffff
je .invalid
@@:
; TODO: check if it's not a multicast
xor eax, eax
ret
.invalid:
DEBUGF 1, "Invalid MAC!\n"
xor eax, eax
inc eax
ret
align 16
alx_get_perm_macaddr:
; try to get it from register first
call alx_read_macaddr
test eax, eax
jz .done
; try to load from efuse
mov esi, [ebx + device.mmio_addr]
mov ecx, ALX_SLD_MAX_TO
.loop1:
mov eax, dword[esi + ALX_SLD]
test eax, ALX_SLD_STAT or ALX_SLD_START
jz @f
dec ecx
jz .error
push esi ecx
xor esi, esi
inc esi
invoke Sleep
pop ecx esi
jmp .loop1
@@:
or eax, ALX_SLD_START
mov dword[esi + ALX_SLD], eax
mov ecx, ALX_SLD_MAX_TO
.loop2:
mov eax, dword[esi + ALX_SLD]
test eax, ALX_SLD_START
jz @f
dec ecx
jz .error
push esi ecx
xor esi, esi
inc esi
invoke Sleep
pop ecx esi
jmp .loop2
@@:
call alx_read_macaddr
test eax, eax
jz .done
; try to load from flash/eeprom (if present)
set_io [ebx + device.io_addr], 0
set_io [ebx + device.io_addr], ALX_EFLD
in eax, dx
test eax, ALX_EFLD_F_EXIST or ALX_EFLD_E_EXIST
jz .error
mov ecx, ALX_SLD_MAX_TO
.loop3:
in eax, dx
test eax, ALX_EFLD_STAT or ALX_EFLD_START
jz @f
dec ecx
jz .error
push esi edx ecx
xor esi, esi
inc esi
invoke Sleep
pop ecx edx esi
jmp .loop3
@@:
or eax, ALX_EFLD_START
out dx, eax
mov ecx, ALX_SLD_MAX_TO
.loop4:
in eax, dx
test eax, ALX_EFLD_START
jz @f
dec ecx
jz .error
push esi edx ecx
xor esi, esi
inc esi
invoke Sleep
pop ecx edx esi
jmp .loop4
@@:
call alx_read_macaddr
test eax, eax
jz .done
.error:
DEBUGF 1, "error obtaining MAC\n"
xor eax, eax
dec eax
ret
.done:
DEBUGF 1, "MAC OK\n"
xor eax, eax
ret
align 16
alx_stop_mac:
DEBUGF 1,"alx_stop_mac\n"
mov esi, [ebx + device.mmio_addr]
mov eax, dword[esi + ALX_RXQ0]
and eax, not ALX_RXQ0_EN
mov dword[esi + ALX_RXQ0], eax
mov eax, dword[esi + ALX_TXQ0]
and eax, not ALX_TXQ0_EN
mov dword[esi + ALX_TXQ0], eax
push esi
xor esi, esi
inc esi
invoke Sleep ; FIME: udelay(40)
pop esi
mov eax, [ebx + device.rx_ctrl]
and eax, not(ALX_MAC_CTRL_TX_EN or ALX_MAC_CTRL_RX_EN)
mov [ebx + device.rx_ctrl], eax
mov [esi + ALX_MAC_CTRL], eax
mov ecx, ALX_DMA_MAC_RST_TO
.loop:
mov eax, [esi + ALX_MAC_STS]
test eax, ALX_MAC_STS_IDLE
jz .done
push esi
xor esi, esi
inc esi
invoke Sleep ; FIME: udelay(10)
pop esi
dec ecx
jnz .loop
DEBUGF 1,"alx_stop_mac timeout!\n"
xor eax, eax
dec eax
ret
.done:
DEBUGF 1,"alx_stop_mac ok\n"
xor eax, eax
ret
align 16
alx_start_mac:
DEBUGF 1,"alx_start_mac\n"
mov esi, [ebx + device.mmio_addr]
mov eax, dword[esi + ALX_RXQ0]
or eax, ALX_RXQ0_EN
mov dword[esi + ALX_RXQ0], eax
mov eax, dword[esi + ALX_TXQ0]
or eax, ALX_TXQ0_EN
mov dword[esi + ALX_TXQ0], eax
mov eax, [ebx + device.rx_ctrl]
or eax, ALX_MAC_CTRL_TX_EN or ALX_MAC_CTRL_RX_EN
and eax, not ALX_MAC_CTRL_FULLD
test [ebx + device.state], ETH_LINK_FD
jz @f
or eax, ALX_MAC_CTRL_FULLD
@@:
and eax, not (ALX_MAC_CTRL_SPEED_MASK shl ALX_MAC_CTRL_SPEED_SHIFT)
test [ebx + device.state], ETH_LINK_1G
jz .10_100
or eax, (ALX_MAC_CTRL_SPEED_1000 shl ALX_MAC_CTRL_SPEED_SHIFT)
mov [ebx + device.rx_ctrl], eax
mov [esi + ALX_MAC_CTRL], eax
ret
.10_100:
or eax, (ALX_MAC_CTRL_SPEED_10_100 shl ALX_MAC_CTRL_SPEED_SHIFT)
mov [ebx + device.rx_ctrl], eax
mov [esi + ALX_MAC_CTRL], eax
ret
align 16
alx_init_ring_ptrs:
DEBUGF 1,"alx_init_ring_ptrs\n"
mov esi, [ebx + device.mmio_addr]
; Receive descriptors
mov [ebx + device.rxq_read_idx], 0
mov [ebx + device.rxq_write_idx], 0
; mov [ebx + device.rxq_rrd_read_idx], 0
mov dword[esi + ALX_RX_BASE_ADDR_HI], 0
lea eax, [ebx + device.rrd_ring]
invoke GetPhysAddr
mov dword[esi + ALX_RRD_ADDR_LO], eax
mov dword[esi + ALX_RRD_RING_SZ], RX_RING_SIZE
lea eax, [ebx + device.rfd_ring]
invoke GetPhysAddr
mov dword[esi + ALX_RFD_ADDR_LO], eax
mov dword[esi + ALX_RFD_RING_SZ], RX_RING_SIZE
mov dword[esi + ALX_RFD_BUF_SZ], RX_BUFFER_SIZE
; Transmit descriptors
mov [ebx + device.txq_read_idx], 0
mov [ebx + device.txq_write_idx], 0
mov dword[esi + ALX_TX_BASE_ADDR_HI], 0
lea eax, [ebx + device.tpd_ring]
invoke GetPhysAddr
mov dword[esi + ALX_TPD_PRI0_ADDR_LO], eax
mov dword[esi + ALX_TPD_RING_SZ], TX_RING_SIZE
; Load these pointers into the chip
mov dword[esi + ALX_SRAM9], ALX_SRAM_LOAD_PTR
xor eax, eax
ret
align 16
alx_alloc_descriptors:
DEBUGF 1,"alx_alloc_descriptors\n"
; physical tx/rx ring descriptors
; alx->descmem.size = sizeof.tx_desc * TX_RING_SIZE + sizeof.rx_desc * RX_RING_SIZE + sizeof(struct alx_rfd) * RX_RING_SIZE;
; alx->descmem.virt = dma_zalloc_coherent(&alx->hw.pdev->dev, alx->descmem.size, &alx->descmem.dma, GFP_KERNEL);
; if (!alx->descmem.virt)
; goto out_free;
;
; alx->txq.tpd = (void *)alx->descmem.virt;
; alx->txq.tpd_dma = alx->descmem.dma;
; alignment requirement for next block
; BUILD_BUG_ON(tx_desc.sizeof % 8);
;
; alx->rxq.rrd = (void *)((u8 *)alx->descmem.virt + tx_desc.sizeof * TX_RING_SIZE);
; alx->rxq.rrd_dma = alx->descmem.dma + sizeof.tx_desc * TX_RING_SIZE;
;
; alignment requirement for next block
; BUILD_BUG_ON(rx_desc.sizeof % 8);
;
; alx->rxq.rfd = (void *)((u8 *)alx->descmem.virt + sizeof.tx_desx * TX_RING_SIZE + sizeof.rx_desc * RX_RING_SIZE);
; alx->rxq.rfd_dma = alx->descmem.dma + sizeof.tx_desc * TX_RING_SIZE + sizeof.rx_desc * RX_RING_SIZE;
xor eax, eax
ret
align 16
alx_alloc_rings:
DEBUGF 1,"alx_alloc_rings\n"
call alx_alloc_descriptors
test eax, eax
jnz .ret_err
and [ebx + device.int_mask], not ALX_ISR_ALL_QUEUES
or [ebx + device.int_mask], ALX_ISR_TX_Q0 or ALX_ISR_RX_Q0
; netif_napi_add(alx->dev, &alx->napi, alx_poll, 64);
call alx_reinit_rings
.ret_err:
ret
align 16
alx_reinit_rings:
DEBUGF 1,"alx_reinit_rings\n"
call alx_free_rx_ring
call alx_init_ring_ptrs
call alx_refill_rx_ring
ret
align 16
alx_refill_rx_ring:
DEBUGF 1,"alx_refill_rx_ring\n"
mov ecx, [ebx + device.rxq_write_idx]
.loop:
cmp dword[ebx + device.rfd_ring+ecx*sizeof.alx_rfd + alx_rfd.addr_l], 0
jne .done
invoke NetAlloc, NET_BUFF.data+RX_BUFFER_SIZE
test eax, eax
jz .done
mov [ebx + device.rfd_ring_virt + ecx*4], eax
add eax, NET_BUFF.data
invoke GetPhysAddr
mov dword[ebx + device.rfd_ring+ecx*sizeof.alx_rfd + alx_rfd.addr_l], eax
mov dword[ebx + device.rfd_ring+ecx*sizeof.alx_rfd + alx_rfd.addr_h], 0
mov eax, ecx
inc ecx
and ecx, RX_RING_SIZE - 1
cmp ecx, [ebx + device.rxq_read_idx]
jne .loop
mov ecx, eax
.done:
cmp ecx, [ebx + device.rxq_write_idx]
je .none
mov [ebx + device.rxq_write_idx], ecx
mov esi, [ebx + device.mmio_addr]
mov [esi + ALX_RFD_PIDX], cx
.none:
xor eax, eax
ret
align 16
alx_free_rx_ring:
DEBUGF 1,"alx_free_rx_ring\n"
xor ecx, ecx
.loop:
mov eax, [ebx + device.rfd_ring_virt + ecx*4]
test eax, eax
jz .next
invoke NetFree, eax
xor eax, eax
mov dword[ebx + device.rfd_ring+ecx*sizeof.alx_rfd + alx_rfd.addr_l], eax
mov dword[ebx + device.rfd_ring+ecx*sizeof.alx_rfd + alx_rfd.addr_h], eax
mov [ebx + device.rfd_ring_virt + ecx*4], eax
.next:
inc ecx
cmp ecx, RX_RING_SIZE
jb .loop
ret
align 16
alx_configure:
DEBUGF 1,"alx_configure\n"
call alx_configure_basic
call alx_disable_rss
call __alx_set_rx_mode
mov esi, [ebx + device.mmio_addr]
mov eax, [ebx + device.rx_ctrl]
mov [esi + ALX_MAC_CTRL], eax
xor eax, eax
ret
align 16
alx_irq_enable:
DEBUGF 1,"alx_irq_enable\n"
mov esi, [ebx + device.mmio_addr]
mov dword[esi + ALX_ISR], 0
mov eax, [ebx + device.int_mask]
mov [esi + ALX_IMR], eax
call alx_post_write
ret
align 16
alx_irq_disable:
DEBUGF 1,"alx_irq_disable\n"
mov esi, [ebx + device.mmio_addr]
mov dword[esi + ALX_ISR], ALX_ISR_DIS
mov dword[esi + ALX_IMR], 0
call alx_post_write
ret
align 16
alx_post_write:
push eax
mov esi, [ebx + device.mmio_addr]
mov eax, [esi]
pop eax
ret
align 16
alx_configure_basic:
DEBUGF 1,"alx_configure_basic\n"
mov esi, [ebx + device.mmio_addr]
;;; call alx_set_macaddr
mov dword[esi + ALX_CLK_GATE], ALX_CLK_GATE_ALL
; idle timeout to switch clk_125M
cmp [ebx + device.chip_rev], ALX_REV_B0
jb @f
mov dword[esi + ALX_IDLE_DECISN_TIMER], ALX_IDLE_DECISN_TIMER_DEF
@@:
mov dword[esi + ALX_SMB_TIMER], SMB_TIMER * 500
mov eax, [esi + ALX_MASTER]
or eax, ALX_MASTER_IRQMOD2_EN or ALX_MASTER_IRQMOD1_EN or ALX_MASTER_SYSALVTIMER_EN
mov [esi + ALX_MASTER], eax
mov dword[esi + ALX_IRQ_MODU_TIMER], (IMT / 2) shl ALX_IRQ_MODU_TIMER1_SHIFT
; intr re-trig timeout
mov dword[esi + ALX_INT_RETRIG], ALX_INT_RETRIG_TO
; tpd threshold to trig int
mov dword[esi + ALX_TINT_TPD_THRSHLD], ITH_TPD
mov dword[esi + ALX_TINT_TIMER], IMT
mov dword[esi + ALX_MTU], RX_BUFFER_SIZE + 8 ;;;;
mov dword[esi + ALX_TXQ1], (((RX_BUFFER_SIZE + 8 + 7) shr 3) or ALX_TXQ1_ERRLGPKT_DROP_EN)
; rxq, flow control
; TODO set ALX_RXQ2
; RXQ0
mov eax, (ALX_RXQ0_NUM_RFD_PREF_DEF shl ALX_RXQ0_NUM_RFD_PREF_SHIFT) \
or (ALX_RXQ0_RSS_MODE_DIS shl ALX_RXQ0_RSS_MODE_SHIFT) \
or (ALX_RXQ0_IDT_TBL_SIZE_DEF shl ALX_RXQ0_IDT_TBL_SIZE_SHIFT) \
or ALX_RXQ0_RSS_HSTYP_ALL or ALX_RXQ0_RSS_HASH_EN or ALX_RXQ0_IPV6_PARSE_EN
test [ebx + device.pci_did], 1 ;;; FIXME: is gigabit device?
jz @f
or eax, ALX_RXQ0_ASPM_THRESH_100M shl ALX_RXQ0_ASPM_THRESH_SHIFT
@@:
mov dword[esi + ALX_RXQ0], eax
; TODO: DMA
; mov eax, [esi + ALX_DMA] ; read and ignore?
; mov eax, [ebx + device.dma_chnl]
; dec eax
; shl eax, ALX_DMA_RCHNL_SEL_SHIFT
; or eax, (ALX_DMA_RORDER_MODE_OUT shl ALX_DMA_RORDER_MODE_SHIFT) \
; or ALX_DMA_RREQ_PRI_DATA \
; or (max_payload shl ALX_DMA_RREQ_BLEN_SHIFT ) \
; or (ALX_DMA_WDLY_CNT_DEF shl ALX_DMA_WDLY_CNT_SHIFT ) \
; or (ALX_DMA_RDLY_CNT_DEF shl ALX_DMA_RDLY_CNT_SHIFT )
; mov [esi + ALX_DMA], eax
; default multi-tx-q weights
mov eax, (ALX_WRR_PRI_RESTRICT_NONE shl ALX_WRR_PRI_SHIFT) \
or (4 shl ALX_WRR_PRI0_SHIFT) \
or (4 shl ALX_WRR_PRI1_SHIFT) \
or (4 shl ALX_WRR_PRI2_SHIFT) \
or (4 shl ALX_WRR_PRI3_SHIFT)
mov [esi + ALX_WRR], eax
ret
align 16
alx_disable_rss:
DEBUGF 1,"alx_disable_rss\n"
mov esi, [ebx + device.mmio_addr]
mov eax, [esi + ALX_RXQ0]
and eax, not (ALX_RXQ0_RSS_HASH_EN)
mov [esi + ALX_RXQ0] , eax
ret
align 16
__alx_set_rx_mode:
DEBUGF 1,"__alx_set_rx_mode\n"
mov esi, [ebx + device.mmio_addr]
; if (!(netdev->flags & IFF_ALLMULTI)) {
; netdev_for_each_mc_addr(ha, netdev)
; alx_add_mc_addr(hw, ha->addr, mc_hash);
;
; alx_write_mem32(hw, ALX_HASH_TBL0, mc_hash[0]);
; alx_write_mem32(hw, ALX_HASH_TBL1, mc_hash[1]);
; }
mov eax, [ebx + device.rx_ctrl]
or eax, ALX_MAC_CTRL_PROMISC_EN or ALX_MAC_CTRL_MULTIALL_EN
mov [ebx + device.rx_ctrl], eax
mov dword[esi + ALX_MAC_CTRL], eax
ret
align 16
alx_check_link:
call alx_clear_phy_intr
mov edx, [ebx + device.state]
call alx_get_phy_link
cmp eax, 0
jl .reset
mov esi, [ebx + device.mmio_addr]
spin_lock_irqsave
or [ebx + device.int_mask], ALX_ISR_PHY
mov eax, [ebx + device.int_mask]
mov [esi + ALX_IMR], eax
spin_unlock_irqrestore
cmp edx, [ebx + device.state]
je .no_change
cmp [ebx + device.state], ETH_LINK_DOWN
je .link_down
call alx_post_phy_link
mov ecx, (ALX_PMCTRL_L0S_EN or ALX_PMCTRL_L1_EN or ALX_PMCTRL_ASPM_FCEN)
call alx_enable_aspm
call alx_start_mac
invoke NetLinkChanged
ret
.no_change:
DEBUGF 1, "link state unchanged\n"
ret
.link_down:
; Link is now down
call alx_reset_mac
test eax, eax
jnz .reset
call alx_irq_disable
; MAC reset causes all HW settings to be lost, restore all
call alx_reinit_rings
test eax, eax
jnz .reset
call alx_configure
mov ecx, (ALX_PMCTRL_L1_EN or ALX_PMCTRL_ASPM_FCEN)
call alx_enable_aspm
call alx_post_phy_link
call alx_irq_enable
invoke NetLinkChanged
ret
.reset:
DEBUGF 1, "alx_schedule_reset"
;;; call alx_schedule_reset
ret
align 16
alx_post_phy_link:
cmp [ebx + device.chip_rev], ALX_REV_B0
ja .done
cmp [ebx + device.state], ETH_LINK_UNKNOWN
jae @f
; TODO
; stdcall alx_read_phy_ext, ALX_MIIEXT_AFE, ALX_MIIEXT_ANEG
; and eax, not (ALX_AFE_10BT_100M_TH)
; stdcall alx_write_phy_ext, ALX_MIIEXT_AFE, ALX_MIIEXT_ANEG, eax
ret
@@:
.done:
ret
align 16
alx_clear_phy_intr:
stdcall alx_read_phy_reg, 0, ALX_MII_ISR
ret
align 16
alx_get_phy_link:
DEBUGF 1,"alx_get_phy_link\n"
stdcall alx_read_phy_reg, 0, MII_BMSR
stdcall alx_read_phy_reg, 0, MII_BMSR
mov [ebx + device.state], ETH_LINK_DOWN
test ax, BMSR_LSTATUS
jnz @f
DEBUGF 1,"link is down\n"
xor eax, eax
ret
@@:
stdcall alx_read_phy_reg, 0, ALX_MII_GIGA_PSSR
test ax, ALX_GIGA_PSSR_SPD_DPLX_RESOLVED
jz .wrong_speed
DEBUGF 1,"link is up\n"
test ax, ALX_GIGA_PSSR_DPLX
jz @f
or [ebx + device.state], ETH_LINK_FD
DEBUGF 1,"full duplex\n"
@@:
and ax, ALX_GIGA_PSSR_SPEED
cmp ax, ALX_GIGA_PSSR_1000MBS
jne @f
or [ebx + device.state], ETH_LINK_1G
DEBUGF 1,"1 gigabit\n"
ret
@@:
cmp ax, ALX_GIGA_PSSR_100MBS
jne @f
or [ebx + device.state], ETH_LINK_100M
DEBUGF 1,"100 mbit\n"
ret
@@:
cmp ax, ALX_GIGA_PSSR_10MBS
jne @f
or [ebx + device.state], ETH_LINK_10M
DEBUGF 1,"10 mbit\n"
ret
@@:
mov [ebx + device.state], ETH_LINK_UNKNOWN
DEBUGF 1,"speed unknown\n"
ret
.wrong_speed:
DEBUGF 1,"wrong speed\n"
xor eax, eax
dec eax
ret
align 16
proc alx_read_phy_reg stdcall, phy_addr:dword, reg:dword
; FIXME: Only internal PHY for now, fixed clock
DEBUGF 1,"PHY read, addr=0x%x reg=0x%x\n", [phy_addr]:8, [reg]:8
mov esi, [ebx + device.mmio_addr]
mov eax, [reg]
shl eax, ALX_MDIO_REG_SHIFT
or eax, ALX_MDIO_SPRES_PRMBL or (ALX_MDIO_CLK_SEL_25MD4 shl ALX_MDIO_CLK_SEL_SHIFT) or ALX_MDIO_START or ALX_MDIO_OP_READ
mov dword[esi + ALX_MDIO], eax
mov ecx, ALX_MDIO_MAX_AC_TO
.loop:
mov eax, dword[esi + ALX_MDIO]
test eax, ALX_MDIO_BUSY
jz .ready
push esi ecx
xor esi, esi
inc esi
invoke Sleep ;; FIXME: udelay(10)
pop ecx esi
dec ecx
jnz .loop
DEBUGF 1,"PHY read timeout!\n"
xor eax, eax
dec eax
ret
.ready:
; shr eax, ALX_MDIO_DATA_SHIFT
and eax, ALX_MDIO_DATA_MASK
DEBUGF 1,"PHY read, val=0x%x\n", eax:4
ret
endp
align 16
proc alx_write_phy_reg stdcall, phy_addr:dword, reg:dword, val:dword
; FIXME: Only internal PHY for now, fixed clock
DEBUGF 1,"PHY write, addr=0x%x reg=0x%x, data=0x%x\n", [phy_addr]:8, [reg]:8, [val]:8
mov esi, [ebx + device.mmio_addr]
mov eax, [reg]
shl eax, ALX_MDIO_REG_SHIFT
mov ax, word[val] ; data must be in 16 lower bits :)
or eax, ALX_MDIO_SPRES_PRMBL or (ALX_MDIO_CLK_SEL_25MD4 shl ALX_MDIO_CLK_SEL_SHIFT) or ALX_MDIO_START
mov dword[esi + ALX_MDIO], eax
mov ecx, ALX_MDIO_MAX_AC_TO
.loop:
mov eax, dword[esi + ALX_MDIO]
test eax, ALX_MDIO_BUSY
jz .ready
push esi ecx
xor esi, esi
inc esi
invoke Sleep ;; FIXME: udelay(10)
pop ecx esi
dec ecx
jnz .loop
DEBUGF 1,"PHY write timeout!\n"
xor eax, eax
dec eax
ret
.ready:
DEBUGF 1,"PHY write OK\n"
xor eax, eax
ret
endp
align 16
alx_request_irq:
DEBUGF 1,"Request IRQ\n"
mov esi, [ebx + device.mmio_addr]
; Only legacy interrupts supported for now.
mov dword[esi + ALX_MSI_RETRANS_TIMER], 0
ret
; End of code
data fixups
end data
include '../peimport.inc'
my_service db 'AR81XX',0 ; max 16 chars include zero
chiplist:
dd (ALX_DEV_ID_AR8131 shl 16) or ALX_VEN_ID, ar8131_sz
dd (ALX_DEV_ID_AR8161 shl 16) or ALX_VEN_ID, ar8161_sz
dd (ALX_DEV_ID_AR8162 shl 16) or ALX_VEN_ID, ar8162_sz
dd (ALX_DEV_ID_AR8171 shl 16) or ALX_VEN_ID, ar8171_sz
dd (ALX_DEV_ID_AR8172 shl 16) or ALX_VEN_ID, ar8172_sz
dd (ALX_DEV_ID_E2200 shl 16) or ALX_VEN_ID, e2200_sz
dd (ALX_DEV_ID_E2400 shl 16) or ALX_VEN_ID, e2400_sz
dd (ALX_DEV_ID_E2500 shl 16) or ALX_VEN_ID, e2500_sz
dd 0
ar8131_sz db "AR8131", 0
ar8161_sz db "AR8161", 0
ar8162_sz db "AR8162", 0
ar8171_sz db "QCA8171", 0
ar8172_sz db "QCA8172", 0
e2200_sz db "Killer E2200", 0
e2400_sz db "Killer E2400", 0
e2500_sz db "Killer E2500", 0
include_debug_strings
align 4
devices dd 0
device_list rd MAX_DEVICES ; This list contains all pointers to device structures the driver is handling