kolibrios-gitea/kernel/trunk/bus/usb/scheduler.inc

1088 lines
39 KiB
PHP
Raw Normal View History

; Implementation of periodic transaction scheduler for USB.
; Bandwidth dedicated to periodic transactions is limited, so
; different pipes should be scheduled as uniformly as possible.
; USB1 scheduler.
; Algorithm is simple:
; when adding a pipe, optimize the following quantity:
; * for every millisecond, take all bandwidth scheduled to periodic transfers,
; * calculate maximum over all milliseconds,
; * select a variant which minimizes that maximum;
; when removing a pipe, do nothing (except for bookkeeping).
; sanity check: structures in UHCI and OHCI should be the same
if (sizeof.ohci_static_ep=sizeof.uhci_static_ep)&(ohci_static_ep.SoftwarePart=uhci_static_ep.SoftwarePart)&(ohci_static_ep.NextList=uhci_static_ep.NextList)
; Select a list for a new pipe.
; in: esi -> usb_controller, maxpacket, type, interval can be found in the stack
; in: ecx = 2 * maximal interval = total number of periodic lists + 1
; in: edx -> {u|o}hci_static_ep for the first list
; in: eax -> byte past {u|o}hci_static_ep for the last list in the first group
; out: edx -> usb_static_ep for the selected list or zero if failed
proc usb1_select_interrupt_list
; inherit some variables from usb_open_pipe
virtual at ebp-12
.speed db ?
rb 3
.bandwidth dd ?
.target dd ?
dd ?
dd ?
.config_pipe dd ?
.endpoint dd ?
.maxpacket dd ?
.type dd ?
.interval dd ?
end virtual
push ebx edi ; save used registers to be stdcall
push eax ; save eax for checks in step 3
; 1. Only intervals 2^k ms can be supported.
; The core specification says that the real interval should not be greater
; than the interval given by the endpoint descriptor, but can be less.
; Determine the actual interval as 2^k ms.
mov eax, ecx
; 1a. Set [.interval] to 1 if it was zero; leave it as is otherwise
cmp [.interval], 1
adc [.interval], 0
; 1b. Divide ecx by two while it is strictly greater than [.interval].
@@:
shr ecx, 1
cmp [.interval], ecx
jb @b
; ecx = the actual interval
;
; For example, let ecx = 8, eax = 64.
; The scheduler space is 32 milliseconds,
; we need to schedule something every 8 ms;
; there are 8 variants: schedule at times 0,8,16,24,
; schedule at times 1,9,17,25,..., schedule at times 7,15,23,31.
; Now concentrate: there are three nested loops,
; * the innermost loop calculates the total periodic bandwidth scheduled
; in the given millisecond,
; * the intermediate loop calculates the maximum over all milliseconds
; in the given variant, that is the quantity we're trying to minimize,
; * the outermost loop checks all variants.
; 2. Calculate offset between the first list and the first list for the
; selected interval, in bytes; save in the stack for step 4.
sub eax, ecx
sub eax, ecx
imul eax, sizeof.ohci_static_ep
push eax
imul ebx, ecx, sizeof.ohci_static_ep
; 3. Select the best variant.
; 3a. The outermost loop.
; Prepare for the loop: set the current optimal bandwidth to maximum
; possible value (so that any variant will pass the first comparison),
; calculate delta for the intermediate loop.
or [.bandwidth], -1
.varloop:
; 3b. The intermediate loop.
; Prepare for the loop: set the maximum to be calculated to zero,
; save counter of the outermost loop.
xor edi, edi
push edx
virtual at esp
.cur_variant dd ? ; step 3b
.result_delta dd ? ; step 2
.group1_limit dd ? ; function prolog
end virtual
.calc_max_bandwidth:
; 3c. The innermost loop. Sum over all lists.
xor eax, eax
push edx
.calc_bandwidth:
add eax, [edx+ohci_static_ep.SoftwarePart+usb_static_ep.Bandwidth]
mov edx, [edx+ohci_static_ep.NextList]
test edx, edx
jnz .calc_bandwidth
pop edx
; 3d. The intermediate loop continued: update maximum.
cmp eax, edi
jb @f
mov edi, eax
@@:
; 3e. The intermediate loop continued: advance counter.
add edx, ebx
cmp edx, [.group1_limit]
jb .calc_max_bandwidth
; 3e. The intermediate loop done: restore counter of the outermost loop.
pop edx
; 3f. The outermost loop continued: if the current variant is
; better (maybe not strictly) then the previous optimum, update
; the optimal bandwidth and resulting list.
cmp edi, [.bandwidth]
ja @f
mov [.bandwidth], edi
mov [.target], edx
@@:
; 3g. The outermost loop continued: advance counter.
add edx, sizeof.ohci_static_ep
dec ecx
jnz .varloop
; 4. Calculate bandwidth for the new pipe.
mov eax, [.maxpacket]
mov cl, [.speed]
mov ch, byte [.endpoint]
and ch, 80h
call calc_usb1_bandwidth
; 5. Get the pointer to the best list.
pop edx ; restore value from step 2
pop ecx ; purge stack var from prolog
add edx, [.target]
; 6. Check that bandwidth for the new pipe plus old bandwidth
; still fits to maximum allowed by the core specification, 90% of 12000 bits.
mov ecx, eax
add ecx, [.bandwidth]
cmp ecx, 10800
ja .no_bandwidth
; 7. Convert {o|u}hci_static_ep to usb_static_ep, update bandwidth and return.
add edx, ohci_static_ep.SoftwarePart
add [edx+usb_static_ep.Bandwidth], eax
pop edi ebx ; restore used registers to be stdcall
ret
.no_bandwidth:
dbgstr 'Periodic bandwidth limit reached'
xor edx, edx
pop edi ebx
ret
endp
; sanity check, part 2
else
.err select_interrupt_list must be different for UHCI and OHCI
end if
; Pipe is removing, update the corresponding lists.
; We do not reorder anything, so just update book-keeping variable
; in the list header.
proc usb1_interrupt_list_unlink
virtual at esp
dd ? ; return address
.maxpacket dd ?
.lowspeed db ?
.direction db ?
rb 2
end virtual
; calculate bandwidth on the bus
mov eax, [.maxpacket]
mov ecx, dword [.lowspeed]
call calc_usb1_bandwidth
; find list header
mov edx, ebx
@@:
mov edx, [edx+usb_pipe.NextVirt]
cmp [edx+usb_pipe.Controller], esi
jz @b
; subtract pipe bandwidth
sub [edx+usb_static_ep.Bandwidth], eax
ret 8
endp
; Helper procedure for USB1 scheduler: calculate bandwidth on the bus.
; in: low 11 bits of eax = payload size in bytes
; in: cl = 0 - full-speed, nonzero - high-speed
; in: ch = 0 - OUT, nonzero - IN
; out: eax = maximal bandwidth in FS-bits
proc calc_usb1_bandwidth
and eax, (1 shl 11) - 1 ; get payload for one transaction
add eax, 3 ; add 3 bytes for other fields in data packet, PID+CRC16
test cl, cl
jnz .low_speed
; Multiply by 8 for bytes -> bits, by 7/6 to accomodate bit stuffing
; and by 401/400 for IN transfers to accomodate timers difference
; 9+107/300 for IN transfers, 9+1/3 for OUT transfers
; For 0 <= eax < 09249355h, floor(eax * 107/300) = floor(eax * 5B4E81B5h / 2^32).
; For 0 <= eax < 80000000h, floor(eax / 3) = floor(eax * 55555556h / 2^32).
mov edx, 55555556h
test ch, ch
jz @f
mov edx, 5B4E81B5h
@@:
lea ecx, [eax*9]
mul edx
; Add 93 extra bits: 39 bits for Token packet (8 for SYNC, 24 for token+address,
; 4 extra bits for possible bit stuffing in token+address, 3 for EOP),
; 18 bits for bus turn-around, 11 bits for SYNC+EOP in Data packet plus 1 bit
; for possible timers difference, 2 bits for inter-packet delay, 20 bits for
; Handshake packet, 2 bits for another inter-packet delay.
lea eax, [ecx+edx+93]
ret
.low_speed:
; Multiply by 8 for bytes -> bits, by 7/6 to accomodate bit stuffing,
; by 8 for LS -> FS and by 406/50 for IN transfers to accomodate timers difference.
; 75+59/75 for IN transfers, 74+2/3 for OUT transfers.
mov edx, 0AAAAAABh
test ch, ch
mov ecx, 74
jz @f
mov edx, 0C962FC97h
inc ecx
@@:
imul ecx, eax
mul edx
; Add 778 extra bits:
; 16 bits for PRE packet, 4 bits for hub delay, 8*39 bits for Token packet
; 8*18 bits for bus turn-around
; (406/50)*11 bits for SYNC+EOP in Data packet,
; 8*2 bits for inter-packet delay,
; 16 bits for PRE packet, 4 bits for hub delay, 8*20 bits for Handshake packet,
; 8*2 bits for another inter-packet delay.
lea eax, [ecx+edx+778]
ret
endp
; USB2 scheduler.
; There are two parts: high-speed pipes and split-transaction pipes.
;
; High-speed scheduler uses the same algorithm as USB1 scheduler:
; when adding a pipe, optimize the following quantity:
; * for every microframe, take all bandwidth scheduled to periodic transfers,
; * calculate maximum over all microframes,
; * select a variant which minimizes that maximum;
; * if there are several such variants,
; prefer those that are closer to end of frame
; to minimize collisions with split transactions;
; when removing a pipe, do nothing (except for bookkeeping).
; in: esi -> usb_controller
; out: edx -> usb_static_ep, eax = S-Mask
proc ehci_select_hs_interrupt_list
; inherit some variables from usb_open_pipe
virtual at ebp-12
.targetsmask dd ?
.bandwidth dd ?
.target dd ?
dd ?
dd ?
.config_pipe dd ?
.endpoint dd ?
.maxpacket dd ?
.type dd ?
.interval dd ?
end virtual
; prolog, initialize local vars
or [.bandwidth], -1
or [.target], -1
or [.targetsmask], -1
push ebx edi ; save used registers to be stdcall
; 1. In EHCI, every list describes one millisecond = 8 microframes.
; Thus, there are two significantly different branches:
; for pipes with interval >= 8 microframes, advance to 2,
; for pipes which should be planned in every frame (one or more microframes),
; go to 9.
; Note: the actual interval for high-speed devices is 2^([.interval]-1),
; (the core specification forbids [.interval] == 0)
mov ecx, [.interval]
dec ecx
cmp ecx, 3
jb .every_frame
; 2. Determine the actual interval in milliseconds.
sub ecx, 3
cmp ecx, 5 ; maximum 32ms
jbe @f
movi ecx, 5
@@:
; There are four nested loops,
; * Loop #4 (the innermost one) calculates the total periodic bandwidth
; scheduled in the given microframe of the given millisecond.
; * Loop #3 calculates the maximum over all milliseconds
; in the given variant, that is the quantity we're trying to minimize.
; * Loops #1 and #2 check all variants;
; loop #1 is responsible for the target millisecond,
; loop #2 is responsible for the microframe within millisecond.
; 3. Prepare for loops.
; ebx = number of iterations of loop #1
; [esp] = delta of counter for loop #3, in bytes
; [esp+4] = delta between the first group and the target group, in bytes
movi ebx, 1
movi edx, sizeof.ehci_static_ep
shl ebx, cl
shl edx, cl
mov eax, 64*sizeof.ehci_static_ep
sub eax, edx
sub eax, edx
push eax
push edx
; 4. Select the best variant.
; 4a. Loop #1: initialize counter = pointer to ehci_static_ep for
; the target millisecond in the first group.
lea edx, [esi+ehci_controller.IntEDs-sizeof.ehci_controller]
.varloop0:
; 4b. Loop #2: initialize counter = microframe within the target millisecond.
xor ecx, ecx
.varloop:
; 4c. Loop #3: save counter of loop #1,
; initialize counter with the value of loop #1 counter,
; initialize maximal bandwidth = zero.
xor edi, edi
push edx
virtual at esp
.saved_counter1 dd ? ; step 4c
.loop3_delta dd ? ; step 3
.target_delta dd ? ; step 3
end virtual
.calc_max_bandwidth:
; 4d. Loop #4: initialize counter with the value of loop #3 counter,
; initialize total bandwidth = zero.
xor eax, eax
push edx
.calc_bandwidth:
; 4e. Loop #4: add the bandwidth from the current list
; and advance to the next list, while there is one.
add ax, [edx+ehci_static_ep.Bandwidths+ecx*2]
mov edx, [edx+ehci_static_ep.NextList]
test edx, edx
jnz .calc_bandwidth
; 4f. Loop #4 end: restore counter of loop #3.
pop edx
; 4g. Loop #3: update maximal bandwidth.
cmp eax, edi
jb @f
mov edi, eax
@@:
; 4h. Loop #3: advance the counter and repeat while within the first group.
lea eax, [esi+ehci_controller.IntEDs+32*sizeof.ehci_static_ep-sizeof.ehci_controller]
add edx, [.loop3_delta]
cmp edx, eax
jb .calc_max_bandwidth
; 4i. Loop #3 end: restore counter of loop #1.
pop edx
; 4j. Loop #2: if the current variant is better (maybe not strictly)
; then the previous optimum, update the optimal bandwidth and the target.
cmp edi, [.bandwidth]
ja @f
jb .update
cmp ecx, [.targetsmask]
jb @f
.update:
mov [.bandwidth], edi
mov [.target], edx
mov [.targetsmask], ecx
@@:
; 4k. Loop #2: continue 8 times for every microframe.
inc ecx
cmp ecx, 8
jb .varloop
; 4l. Loop #1: advance counter and repeat ebx times,
; ebx was calculated in step 3.
add edx, sizeof.ehci_static_ep
dec ebx
jnz .varloop0
; 5. Calculate bandwidth for the new pipe.
mov eax, [.maxpacket]
call calc_hs_bandwidth
mov ecx, [.maxpacket]
shr ecx, 11
inc ecx
and ecx, 3
imul eax, ecx
; 6. Get the pointer to the best list.
pop edx ; restore value from step 3
pop edx ; get delta calculated in step 3
add edx, [.target]
; 7. Check that bandwidth for the new pipe plus old bandwidth
; still fits to maximum allowed by the core specification
; current [.bandwidth] + new bandwidth <= limit;
; USB2 specification allows maximum 60000*80% bit times for periodic microframe
mov ecx, [.bandwidth]
add ecx, eax
cmp ecx, 48000
ja .no_bandwidth
; 8. Convert {o|u}hci_static_ep to usb_static_ep, update bandwidth and return.
mov ecx, [.targetsmask]
add [edx+ehci_static_ep.Bandwidths+ecx*2], ax
add edx, ehci_static_ep.SoftwarePart
movi eax, 1
shl eax, cl
pop edi ebx ; restore used registers to be stdcall
ret
.no_bandwidth:
dbgstr 'Periodic bandwidth limit reached'
xor eax, eax
xor edx, edx
pop edi ebx
ret
.every_frame:
; The pipe should be scheduled every frame in two or more microframes.
; 9. Calculate maximal bandwidth for every microframe: three nested loops.
; 9a. The outermost loop: ebx = microframe to calculate.
xor ebx, ebx
.calc_all_bandwidths:
; 9b. The intermediate loop:
; edx = pointer to ehci_static_ep in the first group, [esp] = counter,
; edi = maximal bandwidth
lea edx, [esi+ehci_controller.IntEDs-sizeof.ehci_controller]
xor edi, edi
push 32
.calc_max_bandwidth2:
; 9c. The innermost loop: calculate bandwidth for the given microframe
; in the given frame.
xor eax, eax
push edx
.calc_bandwidth2:
add ax, [edx+ehci_static_ep.Bandwidths+ebx*2]
mov edx, [edx+ehci_static_ep.NextList]
test edx, edx
jnz .calc_bandwidth2
pop edx
; 9d. The intermediate loop continued: update maximal bandwidth.
cmp eax, edi
jb @f
mov edi, eax
@@:
add edx, sizeof.ehci_static_ep
dec dword [esp]
jnz .calc_max_bandwidth2
pop eax
; 9e. Push the calculated maximal bandwidth and continue the outermost loop.
push edi
inc ebx
cmp ebx, 8
jb .calc_all_bandwidths
virtual at esp
.bandwidth7 dd ?
.bandwidth6 dd ?
.bandwidth5 dd ?
.bandwidth4 dd ?
.bandwidth3 dd ?
.bandwidth2 dd ?
.bandwidth1 dd ?
.bandwidth0 dd ?
end virtual
; 10. Select the best variant.
; edx = S-Mask = bitmask of scheduled microframes
movi edx, 0x11
cmp ecx, 1
ja @f
mov dl, 0x55
jz @f
mov dl, 0xFF
@@:
; try all variants edx, edx shl 1, edx shl 2, ...
; while they fit in the lower byte (8 microframes per frame)
.select_best_mframe:
xor edi, edi
mov ecx, edx
mov eax, esp
.calc_mframe:
add cl, cl
jnc @f
cmp edi, [eax]
jae @f
mov edi, [eax]
@@:
add eax, 4
test cl, cl
jnz .calc_mframe
cmp [.bandwidth], edi
jb @f
mov [.bandwidth], edi
mov [.targetsmask], edx
@@:
add dl, dl
jnc .select_best_mframe
; 11. Restore stack after step 9.
add esp, 8*4
; 12. Get the pointer to the target list (responsible for every microframe).
lea edx, [esi+ehci_controller.IntEDs.SoftwarePart+62*sizeof.ehci_static_ep-sizeof.ehci_controller]
; 13. Calculate bandwidth on the bus.
mov eax, [.maxpacket]
call calc_hs_bandwidth
mov ecx, [.maxpacket]
shr ecx, 11
inc ecx
and ecx, 3
imul eax, ecx
; 14. Check that current [.bandwidth] + new bandwidth <= limit;
; USB2 specification allows maximum 60000*80% bit times for periodic microframe.
mov ecx, [.bandwidth]
add ecx, eax
cmp ecx, 48000
ja .no_bandwidth
; 15. Update bandwidths including the new pipe.
mov ecx, [.targetsmask]
lea edi, [edx+ehci_static_ep.Bandwidths-ehci_static_ep.SoftwarePart]
.update_bandwidths:
shr ecx, 1
jnc @f
add [edi], ax
@@:
add edi, 2
test ecx, ecx
jnz .update_bandwidths
; 16. Return target list and target S-Mask.
mov eax, [.targetsmask]
pop edi ebx ; restore used registers to be stdcall
ret
endp
; Pipe is removing, update the corresponding lists.
; We do not reorder anything, so just update book-keeping variable
; in the list header.
proc ehci_hs_interrupt_list_unlink
movzx eax, word [ebx+ehci_pipe.Token-sizeof.ehci_pipe+2]
; calculate bandwidth
call calc_hs_bandwidth
mov ecx, [ebx+ehci_pipe.Flags-sizeof.ehci_pipe]
shr ecx, 30
imul eax, ecx
movzx ecx, byte [ebx+ehci_pipe.Flags-sizeof.ehci_pipe]
; get target list
mov edx, [ebx+ehci_pipe.BaseList-sizeof.ehci_pipe]
; update bandwidth
.dec_bandwidth:
shr ecx, 1
jnc @f
sub word [edx+ehci_static_ep.Bandwidths - ehci_static_ep.SoftwarePart], ax
@@:
add edx, 2
test ecx, ecx
jnz .dec_bandwidth
; return
ret
endp
; Helper procedure for USB2 scheduler: calculate bandwidth on the bus.
; in: low 11 bits of eax = payload size in bytes
; out: eax = maximal bandwidth in HS-bits
proc calc_hs_bandwidth
and eax, (1 shl 11) - 1 ; get payload for one transaction
add eax, 3 ; add 3 bytes for other fields in data packet, PID+CRC16
; Multiply by 8 for bytes -> bits and then by 7/6 to accomodate bit stuffing;
; total 28/3 = 9+1/3
mov edx, 55555556h
lea ecx, [eax*9]
mul edx
; Add 989 extra bits: 68 bits for Token packet (32 for SYNC, 24 for token+address,
; 4 extra bits for possible bit stuffing in token+address, 8 for EOP),
; 736 bits for bus turn-around, 40 bits for SYNC+EOP in Data packet,
; 8 bits for inter-packet delay, 49 bits for Handshake packet,
; 88 bits for another inter-packet delay.
lea eax, [ecx+edx+989]
ret
endp
; Split-transaction scheduler (aka TT scheduler, TT stands for Transaction
; Translator, section 11.14 of the core spec) needs to schedule three event
; types on two buses: Start-Split and Complete-Split on HS bus and normal
; transaction on FS/LS bus.
; Assume that FS/LS bus is more restricted and more important to be scheduled
; uniformly, so select the variant which minimizes maximal used bandwidth
; on FS/LS bus and does not overflow HS bus.
; If there are several such variants, prefer variants which is closest to
; start of frame, and within the same microframe consider HS bandwidth
; utilization as a last criteria.
; The procedure ehci_select_tt_interrupt_list has been splitted into several
; macro, each representing a logical step of the procedure,
; to simplify understanding what is going on. Consider all the following macro
; as logical parts of one procedure, they are meaningless outside the context.
; Given a frame, calculate bandwidth occupied by already opened pipes
; in every microframe.
; Look for both HS and FS/LS buses: there are 16 words of information,
; 8 for HS bus, 8 for FS/LS bus, for every microframe.
; Since we count already opened pipes, the total bandwidth in every microframe
; is less than 60000 bits (and even 60000*80% bits), otherwise the scheduler
; would not allow to open those pipes.
; edi -> first list for the frame
macro tt_calc_bandwidth_in_frame
{
local .lists, .pipes, .pipes_done, .carry
; 1. Zero everything.
xor eax, eax
mov edx, edi
repeat 4
mov dword [.budget+(%-1)*4], eax
end repeat
repeat 4
mov dword [.hs_bandwidth+(%-1)*4], eax
end repeat
mov [.total_budget], ax
; Loop over all lists for the given frame.
.lists:
; 2. Total HS bandwidth for all pipes in one list is kept inside list header,
; add it. Note that overflow is impossible, so we may add entire dwords.
mov ebx, [edx+ehci_static_ep.SoftwarePart+usb_static_ep.NextVirt]
repeat 4
mov eax, dword [edx+ehci_static_ep.Bandwidths+(%-1)*4]
add dword [.hs_bandwidth+(%-1)*4], eax
end repeat
; Loop over all pipes in the given list.
add edx, ehci_static_ep.SoftwarePart
.pipes:
cmp ebx, edx
jz .pipes_done
; 3. For every pipe in every list for the given frame:
; 3a. Check whether the pipe resides on the same FS/LS bus as the new pipe.
; If not, skip this pipe.
mov eax, [ebx+usb_pipe.DeviceData]
mov eax, [eax+usb_device_data.TTHub]
cmp eax, [.tthub]
jnz @f
; 3b. Calculate FS/LS budget for the opened pipe.
; Note that eax = TTHub after 3a.
call tt_calc_budget
; 3c. Update total budget: add the value from 3b
; to the budget of the first microframe scheduled for this pipe.
bsf ecx, [ebx+ehci_pipe.Flags-sizeof.ehci_pipe]
add [.budget+ecx*2], ax
@@:
mov ebx, [ebx+usb_pipe.NextVirt]
jmp .pipes
.pipes_done:
mov edx, [edx+ehci_static_ep.NextList-ehci_static_ep.SoftwarePart]
test edx, edx
jnz .lists
; 4. If the budget for some microframe is exceeded, carry it to the following
; microframe(s). The actual size of one microframe is 187.5 raw bytes;
; the core spec says that 188 bytes should be scheduled in every microframe.
xor eax, eax
xor ecx, ecx
.carry:
xor edx, edx
add ax, [.budget+ecx*2]
cmp ax, 188
jbe @f
mov dx, ax
mov ax, 188
sub dx, ax
@@:
mov [.budget+ecx*2], ax
add [.total_budget], ax
mov ax, dx
inc ecx
cmp ecx, 8
jb .carry
}
; Checks whether the new pipe fits in the existing FS budget
; starting from the given microframe. If not, mark the microframe
; as impossible for scheduling.
; in: ecx = microframe
macro tt_exclude_microframe_if_no_budget
{
local .loop, .good, .bad
; 1. If the new budget plus the current budget does not exceed 188 bytes,
; the variant is possible.
mov ax, [.budget+ecx*2]
mov edx, ecx
add ax, [.new_budget]
sub ax, 188
jbe .good
; 2. Otherwise,
; a) nothing should be scheduled in some following microframes,
; b) after adding the new budget everything should fit in first 6 microframes,
; this guarantees that even in the worst case 90% limit is satisfied.
.loop:
cmp edx, 5
jae .bad
cmp [.budget+(edx+1)*2], 0
jnz .bad
inc edx
sub ax, 188
ja .loop
.bad:
btr [.possible_microframes], ecx
.good:
}
; Calculate data corresponding to the particular scheduling variant for the new pipe.
; Data describe the current scheduling state collected over all frames touched
; by the given variant: maximal HS bandwidth, maximal FS/LS budget,
; which microframes fit in the current FS/LS budget for all frames.
macro tt_calc_statistics_for_one_variant
{
local .frames, .microframes
; 1. Initialize: zero maximal bandwidth,
; first 6 microframes are possible for scheduling.
xor eax, eax
repeat 4
mov dword [.max_hs_bandwidth+(%-1)*4], eax
end repeat
mov [.max_fs_bandwidth], ax
mov [.possible_microframes], 0x3F
; Loop over all frames starting with [.variant] advancing by [.variant_delta].
mov edi, [.variant]
.frames:
; 2. Calculate statistics for one frame.
tt_calc_bandwidth_in_frame
; 3. Update maximal FS budget.
mov ax, [.total_budget]
cmp ax, [.max_fs_bandwidth]
jb @f
mov [.max_fs_bandwidth], ax
@@:
; 4. For every microframe, update maximal HS bandwidth
; and check whether the microframe is allowed for scheduling.
xor ecx, ecx
.microframes:
mov ax, [.hs_bandwidth+ecx*2]
cmp ax, [.max_hs_bandwidth+ecx*2]
jb @f
mov [.max_hs_bandwidth+ecx*2], ax
@@:
tt_exclude_microframe_if_no_budget
inc ecx
cmp ecx, 8
jb .microframes
; Stop loop when outside of first descriptor group.
lea eax, [esi+ehci_controller.IntEDs+32*sizeof.ehci_static_ep-sizeof.ehci_controller]
add edi, [.variant_delta]
cmp edi, eax
jb .frames
}
struct usb_split_info
microframe_mask dd ? ; lower byte is S-mask, second byte is C-mask
ssplit_bandwidth dd ?
csplit_bandwidth dd ?
ends
; Check whether the current variant and the current microframe are allowed
; for scheduling. If so, check whether they are better than the previously
; selected variant+microframe, if any. If so, update the previously selected
; variant+microframe to current ones.
; ecx = microframe, [.variant] = variant
macro tt_check_variant_microframe
{
local .nothing, .update, .ssplit, .csplit, .csplit_done
; 1. If the current microframe does not fit in existing FS budget, do nothing.
bt [.possible_microframes], ecx
jnc .nothing
; 2. Calculate maximal HS bandwidth over all affected microframes.
; 2a. Start-split phase: one or more microframes starting with ecx,
; coded in lower byte of .info.microframe_mask.
xor ebx, ebx
xor edx, edx
.ssplit:
lea eax, [ecx+edx]
movzx eax, [.max_hs_bandwidth+eax*2]
add eax, [.info.ssplit_bandwidth]
cmp ebx, eax
ja @f
mov ebx, eax
@@:
inc edx
bt [.info.microframe_mask], edx
jc .ssplit
; 2b. Complete-split phase: zero or more microframes starting with
; ecx+(last start-split microframe)+2,
; coded in second byte of .info.microframe_mask.
add edx, 8
.csplit:
inc edx
bt [.info.microframe_mask], edx
jnc .csplit_done
lea eax, [ecx+edx]
cmp eax, 8
jae .csplit_done
movzx eax, [.max_hs_bandwidth+(eax-8)*2]
add eax, [.info.csplit_bandwidth]
cmp ebx, eax
ja .csplit
mov ebx, eax
jmp .csplit
.csplit_done:
; 3. Check that current HS bandwidth + new bandwidth <= limit;
; USB2 specification allows maximum 60000*80% bit times for periodic microframe.
cmp ebx, 48000
ja .nothing
; 4. This variant is possible for scheduling.
; Check whether it is better than the currently selected one.
; 4a. The primary criteria: FS/LS bandwidth.
mov ax, [.max_fs_bandwidth]
cmp ax, [.best_fs_bandwidth]
ja .nothing
jb .update
; 4b. The secondary criteria: prefer microframes which are closer to start of frame.
cmp ecx, [.targetsmask]
ja .nothing
jb .update
; 4c. The last criteria: HS bandwidth.
cmp ebx, [.bandwidth]
ja .nothing
.update:
; 5. This variant is better than the previously selected.
; Update the best variant with current data.
mov [.best_fs_bandwidth], ax
mov [.bandwidth], ebx
mov [.targetsmask], ecx
mov eax, [.variant]
mov [.target], eax
.nothing:
}
; TT scheduler: add new pipe.
; in: esi -> usb_controller, edi -> usb_pipe
; out: edx -> usb_static_ep, eax = S-Mask
proc ehci_select_tt_interrupt_list
virtual at ebp-12-.local_vars_size
.local_vars_start:
.info usb_split_info
.new_budget dw ?
.total_budget dw ?
.possible_microframes dd ?
.tthub dd ?
.budget rw 8
.hs_bandwidth rw 8
.max_hs_bandwidth rw 8
.max_fs_bandwidth dw ?
.best_fs_bandwidth dw ?
.variant dd ?
.variant_delta dd ?
.target_delta dd ?
.local_vars_size = $ - .local_vars_start
.targetsmask dd ?
.bandwidth dd ?
.target dd ?
dd ?
dd ?
.config_pipe dd ?
.endpoint dd ?
.maxpacket dd ?
.type dd ?
.interval dd ?
end virtual
mov eax, [edi+ehci_pipe.Token-sizeof.ehci_pipe]
shr eax, 16
and eax, (1 shl 11) - 1
push ebx edi
; 1. Compute the real interval. FS/LS devices encode the interval as
; number of milliseconds. Use the maximal power of two that is not greater than
; the given interval and EHCI scheduling area = 32 frames.
cmp [.interval], 1
adc [.interval], 0
mov ecx, 64
mov eax, 64 * sizeof.ehci_static_ep
@@:
shr ecx, 1
cmp [.interval], ecx
jb @b
mov [.interval], ecx
; 2. Compute variables for further calculations.
; 2a. [.variant_delta] is delta between two lists from the first group
; that correspond to the same variant.
imul ecx, sizeof.ehci_static_ep
mov [.variant_delta], ecx
; 2b. [.target_delta] is delta between the final answer from the group
; corresponding to [.interval] and the item from the first group.
sub eax, ecx
sub eax, ecx
mov [.target_delta], eax
; 2c. [.variant] is the first list from the first group that corresponds
; to the current variant.
lea eax, [esi+ehci_controller.IntEDs-sizeof.ehci_controller]
mov [.variant], eax
; 2d. [.tthub] identifies TT hub for new pipe, [.new_budget] is FS budget
; for new pipe.
mov eax, [edi+usb_pipe.DeviceData]
mov eax, [eax+usb_device_data.TTHub]
mov ebx, edi
mov [.tthub], eax
call tt_calc_budget
mov [.new_budget], ax
; 2e. [.usb_split_info] describes bandwidth used by new pipe on HS bus.
lea edi, [.info]
call tt_fill_split_info
test eax, eax
jz .no_bandwidth
; 2f. There is no best variant yet, put maximal possible values,
; so any variant would be better than the "current".
or [.best_fs_bandwidth], -1
or [.target], -1
or [.bandwidth], -1
or [.targetsmask], -1
; 3. Loop over all variants, for every variant decide whether it is acceptable,
; select the best variant from all acceptable variants.
.check_variants:
tt_calc_statistics_for_one_variant
xor ecx, ecx
.check_microframes:
tt_check_variant_microframe
inc ecx
cmp ecx, 6
jb .check_microframes
add [.variant], sizeof.ehci_static_ep
dec [.interval]
jnz .check_variants
; 4. If there is no acceptable variants, return error.
mov ecx, [.targetsmask]
mov edx, [.target]
cmp ecx, -1
jz .no_bandwidth
; 5. Calculate the answer: edx -> selected list, eax = S-Mask and C-Mask.
mov eax, [.info.microframe_mask]
add edx, [.target_delta]
shl eax, cl
and eax, 0xFFFF
; 6. Update HS bandwidths in the selected list.
xor ecx, ecx
mov ebx, [.info.ssplit_bandwidth]
.update_ssplit:
bt eax, ecx
jnc @f
add [edx+ehci_static_ep.Bandwidths+ecx*2], bx
@@:
inc ecx
cmp ecx, 8
jb .update_ssplit
mov ebx, [.info.csplit_bandwidth]
.update_csplit:
bt eax, ecx
jnc @f
add [edx+ehci_static_ep.Bandwidths+(ecx-8)*2], bx
@@:
inc ecx
cmp ecx, 16
jb .update_csplit
; 7. Return.
add edx, ehci_static_ep.SoftwarePart
pop edi ebx
ret
.no_bandwidth:
dbgstr 'Periodic bandwidth limit reached'
xor eax, eax
xor edx, edx
pop edi ebx
ret
endp
; Pipe is removing, update the corresponding lists.
; We do not reorder anything, so just update book-keeping variable
; in the list header.
proc ehci_fs_interrupt_list_unlink
; calculate bandwidth
push edi
sub esp, sizeof.usb_split_info
mov edi, esp
call tt_fill_split_info
; get target list
mov edx, [ebx+ehci_pipe.BaseList-sizeof.ehci_pipe]
; update bandwidth for Start-Split
mov eax, [edi+usb_split_info.ssplit_bandwidth]
xor ecx, ecx
.dec_bandwidth_1:
bt [ebx+ehci_pipe.Flags-sizeof.ehci_pipe], ecx
jnc @f
sub word [edx+ecx*2+ehci_static_ep.Bandwidths - ehci_static_ep.SoftwarePart], ax
@@:
inc ecx
cmp ecx, 8
jb .dec_bandwidth_1
; update bandwidth for Complete-Split
mov eax, [edi+usb_split_info.csplit_bandwidth]
.dec_bandwidth_2:
bt [ebx+ehci_pipe.Flags-sizeof.ehci_pipe], ecx
jnc @f
sub word [edx+(ecx-8)*2+ehci_static_ep.Bandwidths - ehci_static_ep.SoftwarePart], ax
@@:
inc ecx
cmp ecx, 16
jb .dec_bandwidth_2
add esp, sizeof.usb_split_info
pop edi
ret
endp
; Helper procedure for ehci_select_tt_interrupt_list.
; Calculates "best-case budget" according to the core spec,
; that is, number of bytes (not bits) corresponding to "optimistic" transaction
; time, including inter-packet delays/bus turn-around time,
; but without bit stuffing and timers drift.
; One extra TT-specific delay is added: TT think time from the hub descriptor.
; Similar to calc_usb1_bandwidth with corresponding changes.
; eax -> usb_hub with TT, ebx -> usb_pipe
proc tt_calc_budget
movzx ecx, [eax+usb_hub.HubCharacteristics]
shr ecx, 5
and ecx, 3 ; 1+ecx = TT think time in FS-bytes
mov eax, [ebx+ehci_pipe.Token-sizeof.ehci_pipe]
shr eax, 16
and eax, (1 shl 11) - 1 ; get data length
bt [ebx+ehci_pipe.Token-sizeof.ehci_pipe], 12
jc .low_speed
; Full-speed interrupt IN/OUT:
; 33 bits for Token packet (8 for SYNC, 24 for token+address, 3 for EOP),
; 18 bits for bus turn-around, 11 bits for SYNC+EOP in Data packet,
; 2 bits for inter-packet delay, 19 bits for Handshake packet,
; 2 bits for another inter-packet delay. 85 bits total, pad to 11 bytes.
lea eax, [eax+11+ecx+1]
; 1 byte is minimal TT think time in addition to ecx.
ret
.low_speed:
; Low-speed interrupt IN/OUT:
; multiply by 8 for LS -> FS,
; add 85 bytes as in full-speed interrupt and extra 5 bytes for two PRE packets
; and two hub delays.
; 1 byte is minimal TT think time in addition to ecx.
lea eax, [eax*8+90+ecx+1]
ret
endp
; Helper procedure for TT scheduler.
; Calculates Start-Split/Complete-Split masks and HS bandwidths.
; ebx -> usb_pipe, edi -> usb_split_info
proc tt_fill_split_info
; Interrupt endpoints.
; The core spec says in 5.7.3 "Interrupt Transfer Packet Size Constraints" that:
; The maximum allowable interrupt data payload size is 64 bytes or less for full-speed.
; Low-speed devices are limited to eight bytes or less maximum data payload size.
; This is important for scheduling, it guarantees that in any case transaction fits
; in two microframes (usually one, two if transaction has started too late in the first
; microframe), so check it.
mov eax, [ebx+ehci_pipe.Token-sizeof.ehci_pipe]
mov ecx, 8
bt eax, 12
jc @f
mov ecx, 64
@@:
shr eax, 16
and eax, (1 shl 11) - 1 ; get data length
cmp eax, ecx
ja .error
add eax, 3 ; add 3 bytes for other fields in data packet, PID+CRC16
; Multiply by 8 for bytes -> bits and then by 7/6 to accomodate bit stuffing;
; total 28/3 = 9+1/3
mov edx, 55555556h
lea ecx, [eax*9]
mul edx
; One start-split, three complete-splits (unless the last is too far,
; but this is handled by the caller).
mov eax, [ebx+usb_pipe.LastTD]
mov [edi+usb_split_info.microframe_mask], 0x1C01
; Structure and HS bandwidth of packets depends on the direction.
bt [eax+ehci_gtd.Token-sizeof.ehci_gtd], 8
jc .interrupt_in
.interrupt_out:
; Start-Split phase:
; 77 bits for SPLIT packet (32 for SYNC, 8 for EOP, 32 for data, 5 for bit stuffing),
; 88 bits for inter-packet delay, 68 bits for Token packet,
; 88 bits for inter-packet delay, 40 bits for SYNC+EOP in Data packet,
; 88 bits for last inter-packet delay, total 449 bits.
lea eax, [edx+ecx+449]
mov [edi+usb_split_info.ssplit_bandwidth], eax
; Complete-Split phase:
; 77 bits for SPLIT packet,
; 88 bits for inter-packet delay, 68 bits for Token packet,
; 736 bits for bus turn-around, 49 bits for Handshake packet,
; 8 bits for inter-packet delay, total 1026 bits.
mov [edi+usb_split_info.csplit_bandwidth], 1026
ret
.interrupt_in:
; Start-Split phase:
; 77 bits for SPLIT packet, 88 bits for inter-packet delay,
; 68 bits for Token packet, 88 bits for another inter-packet delay,
; total 321 bits.
mov [edi+usb_split_info.ssplit_bandwidth], 321
; Complete-Split phase:
; 77 bits for SPLIT packet, 88 bits for inter-packet delay,
; 68 bits for Token packet, 736 bits for bus turn-around,
; 40 bits for SYNC+EOP in Data packet, 8 bits for inter-packet delay,
; total 1017 bits.
lea eax, [edx+ecx+1017]
mov [edi+usb_split_info.csplit_bandwidth], eax
ret
.error:
xor eax, eax
ret
endp