forked from KolibriOS/kolibrios
1334 lines
33 KiB
NASM
1334 lines
33 KiB
NASM
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; Copyright (C) KolibriOS team 2004-2008. All rights reserved. ;;
|
|
;; Distributed under terms of the GNU General Public License ;;
|
|
;; ;;
|
|
;; Realtek 8139 driver for KolibriOS ;;
|
|
;; ;;
|
|
;; Written by hidnplayr@kolibrios.org ;;
|
|
;; ;;
|
|
;; 0.1 - x march 2009 ;;
|
|
;; 0.2 - 8 november 2009 ;;
|
|
;; ;;
|
|
;; GNU GENERAL PUBLIC LICENSE ;;
|
|
;; Version 2, June 1991 ;;
|
|
;; ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
format MS COFF
|
|
|
|
API_VERSION equ 0x01000100
|
|
|
|
DEBUG equ 1
|
|
__DEBUG__ equ 1
|
|
__DEBUG_LEVEL__ equ 1
|
|
|
|
include 'proc32.inc'
|
|
include 'imports.inc'
|
|
include 'fdo.inc'
|
|
|
|
OS_BASE equ 0;
|
|
new_app_base equ 0x60400000
|
|
PROC_BASE equ OS_BASE+0x0080000
|
|
|
|
public START
|
|
public service_proc
|
|
public version
|
|
|
|
struc IOCTL {
|
|
.handle dd ?
|
|
.io_code dd ?
|
|
.input dd ?
|
|
.inp_size dd ?
|
|
.output dd ?
|
|
.out_size dd ?
|
|
}
|
|
|
|
virtual at 0
|
|
IOCTL IOCTL
|
|
end virtual
|
|
|
|
struc ETH_DEVICE {
|
|
; pointers to procedures
|
|
.unload dd ?
|
|
.reset dd ?
|
|
.transmit dd ?
|
|
.set_MAC dd ?
|
|
.get_MAC dd ?
|
|
.set_mode dd ?
|
|
.get_mode dd ?
|
|
; status & variables
|
|
.bytes_tx dq ?
|
|
.bytes_rx dq ?
|
|
.packets_tx dd ?
|
|
.packets_rx dd ?
|
|
.mode dd ? ; This dword contains cable status (10mbit/100mbit, full/half duplex, auto negotiation or not,..)
|
|
.name dd ?
|
|
.mac dp ?
|
|
; device specific
|
|
.rx_buffer dd ?
|
|
.tx_buffer dd ?
|
|
.rx_data_offset dd ?
|
|
.io_addr dd ?
|
|
.curr_tx_desc db ?
|
|
.pci_bus db ?
|
|
.pci_dev db ?
|
|
.irq_line db ?
|
|
.hw_ver_id db ?
|
|
.size:
|
|
|
|
}
|
|
|
|
virtual at 0
|
|
device ETH_DEVICE
|
|
end virtual
|
|
|
|
; PCI Bus defines
|
|
|
|
PCI_HEADER_TYPE equ 0x0e ;8 bit
|
|
PCI_BASE_ADDRESS_0 equ 0x10 ;32 bit
|
|
PCI_BASE_ADDRESS_5 equ 0x24 ;32 bits
|
|
PCI_BASE_ADDRESS_SPACE_IO equ 0x01
|
|
PCI_VENDOR_ID equ 0x00 ;16 bit
|
|
PCI_BASE_ADDRESS_IO_MASK equ 0xFFFFFFFC
|
|
|
|
; RTL8139 specific defines
|
|
|
|
MAX_RTL8139 equ 16 ; Max number of devices this driver may handle
|
|
TX_TIMEOUT equ 30 ; 300 milliseconds timeout
|
|
|
|
PCI_REG_CMD equ 0x04 ; command register
|
|
PCI_BIT_PIO equ 0 ; bit0: io space control
|
|
PCI_BIT_MMIO equ 1 ; bit1: memory space control
|
|
PCI_BIT_MASTER equ 2 ; bit2: device acts as a PCI master
|
|
|
|
REG_IDR0 equ 0x00
|
|
REG_MAR0 equ 0x08 ; multicast filter register 0
|
|
REG_MAR4 equ 0x0c ; multicast filter register 4
|
|
REG_TSD0 equ 0x10 ; transmit status of descriptor
|
|
REG_TSAD0 equ 0x20 ; transmit start address of descriptor
|
|
REG_RBSTART equ 0x30 ; RxBuffer start address
|
|
REG_COMMAND equ 0x37 ; command register
|
|
REG_CAPR equ 0x38 ; current address of packet read (word) R/W
|
|
REG_IMR equ 0x3c ; interrupt mask register
|
|
REG_ISR equ 0x3e ; interrupt status register
|
|
REG_TXCONFIG equ 0x40 ; transmit configuration register
|
|
REG_RXCONFIG equ 0x44 ; receive configuration register 0
|
|
REG_MPC equ 0x4c ; missed packet counter
|
|
REG_9346CR equ 0x50 ; serial eeprom 93C46 command register
|
|
REG_CONFIG1 equ 0x52 ; configuration register 1
|
|
REG_MSR equ 0x58
|
|
REG_CONFIG4 equ 0x5a ; configuration register 4
|
|
REG_HLTCLK equ 0x5b ; undocumented halt clock register
|
|
REG_BMCR equ 0x62 ; basic mode control register
|
|
REG_ANAR equ 0x66 ; auto negotiation advertisement register
|
|
REG_9346CR_WE equ 11b SHL 6
|
|
|
|
BIT_RUNT equ 4 ; total packet length < 64 bytes
|
|
BIT_LONG equ 3 ; total packet length > 4k
|
|
BIT_CRC equ 2 ; crc error occured
|
|
BIT_FAE equ 1 ; frame alignment error occured
|
|
BIT_ROK equ 0 ; received packet is ok
|
|
|
|
BIT_RST equ 4 ; reset bit
|
|
BIT_RE equ 3 ; receiver enabled
|
|
BIT_TE equ 2 ; transmitter enabled
|
|
BUFE equ 1 ; rx buffer is empty, no packet stored
|
|
|
|
BIT_ISR_TOK equ 2 ; transmit ok
|
|
BIT_ISR_RER equ 1 ; receive error interrupt
|
|
BIT_ISR_ROK equ 0 ; receive ok
|
|
|
|
BIT_TX_MXDMA equ 8 ; Max DMA burst size per Tx DMA burst
|
|
BIT_TXRR equ 4 ; Tx Retry count 16+(TXRR*16)
|
|
|
|
BIT_RXFTH equ 13 ; Rx fifo threshold
|
|
BIT_RBLEN equ 11 ; Ring buffer length indicator
|
|
BIT_RX_MXDMA equ 8 ; Max DMA burst size per Rx DMA burst
|
|
BIT_NOWRAP equ 7 ; transfered data wrapping
|
|
BIT_9356SEL equ 6 ; eeprom selector 9346/9356
|
|
BIT_AER equ 5 ; accept error packets
|
|
BIT_AR equ 4 ; accept runt packets
|
|
BIT_AB equ 3 ; accept broadcast packets
|
|
BIT_AM equ 2 ; accept multicast packets
|
|
BIT_APM equ 1 ; accept physical match packets
|
|
BIT_AAP equ 0 ; accept all packets
|
|
|
|
BIT_93C46_EEM1 equ 7 ; RTL8139 eeprom operating mode1
|
|
BIT_93C46_EEM0 equ 6 ; RTL8139 eeprom operating mode0
|
|
BIT_93C46_EECS equ 3 ; chip select
|
|
BIT_93C46_EESK equ 2 ; serial data clock
|
|
BIT_93C46_EEDI equ 1 ; serial data input
|
|
BIT_93C46_EEDO equ 0 ; serial data output
|
|
|
|
BIT_LWACT equ 4 ; see REG_CONFIG1
|
|
BIT_SLEEP equ 1 ; sleep bit at older chips
|
|
BIT_PWRDWN equ 0 ; power down bit at older chips
|
|
BIT_PMEn equ 0 ; power management enabled
|
|
|
|
BIT_LWPTN equ 2 ; see REG_CONFIG4
|
|
|
|
BIT_ERTXTH equ 16 ; early TX threshold
|
|
BIT_TOK equ 15 ; transmit ok
|
|
BIT_OWN equ 13 ; tx DMA operation is completed
|
|
|
|
BIT_ANE equ 12 ; auto negotiation enable
|
|
|
|
BIT_TXFD equ 8 ; 100base-T full duplex
|
|
BIT_TX equ 7 ; 100base-T
|
|
BIT_10FD equ 6 ; 10base-T full duplex
|
|
BIT_10 equ 5 ; 10base-T
|
|
BIT_SELECTOR equ 0 ; binary encoded selector CSMA/CD=00001
|
|
|
|
BIT_IFG1 equ 25
|
|
BIT_IFG0 equ 24
|
|
|
|
RBLEN equ 2 ; Receive buffer size: 0==8K 1==16k 2==32k 3==64k
|
|
TXRR equ 8 ; total retries = 16+(TXRR*16)
|
|
TX_MXDMA equ 6 ; 0=16 1=32 2=64 3=128 4=256 5=512 6=1024 7=2048
|
|
ERTXTH equ 8 ; in unit of 32 bytes e.g:(8*32)=256
|
|
RX_MXDMA equ 7 ; 0=16 1=32 2=64 3=128 4=256 5=512 6=1024 7=unlimited
|
|
RXFTH equ 7 ; 0=16 1=32 2=64 3=128 4=256 5=512 6=1024 7=no threshold
|
|
|
|
RX_CONFIG equ (RBLEN shl BIT_RBLEN) or \
|
|
(RX_MXDMA shl BIT_RX_MXDMA) or \
|
|
(1 shl BIT_NOWRAP) or \
|
|
(RXFTH shl BIT_RXFTH) or\
|
|
(1 shl BIT_AB) or \
|
|
(1 shl BIT_APM) or \
|
|
(1 shl BIT_AER) or \
|
|
(1 shl BIT_AR) or \
|
|
(1 shl BIT_AM)
|
|
|
|
RX_BUFFER_SIZE equ (8192 shl RBLEN)
|
|
MAX_ETH_FRAME_SIZE equ 1516 ; exactly 1514 wthout CRC
|
|
NUM_TX_DESC equ 4
|
|
TX_BUF_SIZE equ 4096 ; size of one tx buffer (set to 4kb because of KolibriOS's page size)
|
|
|
|
EE_93C46_REG_ETH_ID equ 7 ; MAC offset
|
|
EE_93C46_READ_CMD equ (6 shl 6) ; 110b + 6bit address
|
|
EE_93C56_READ_CMD equ (6 shl 8) ; 110b + 8bit address
|
|
EE_93C46_CMD_LENGTH equ 9 ; start bit + cmd + 6bit address
|
|
EE_93C56_CMD_LENGTH equ 11 ; start bit + cmd + 8bit ddress
|
|
|
|
VER_RTL8139 equ 1100000b
|
|
VER_RTL8139A equ 1110000b
|
|
VER_RTL8139AG equ 1110100b
|
|
VER_RTL8139B equ 1111000b
|
|
VER_RTL8130 equ VER_RTL8139B
|
|
VER_RTL8139C equ 1110100b
|
|
VER_RTL8100 equ 1111010b
|
|
VER_RTL8100B equ 1110101b
|
|
VER_RTL8139D equ VER_RTL8100B
|
|
VER_RTL8139CP equ 1110110b
|
|
VER_RTL8101 equ 1110111b
|
|
|
|
IDX_RTL8139 equ 0
|
|
IDX_RTL8139A equ 1
|
|
IDX_RTL8139B equ 2
|
|
IDX_RTL8139C equ 3
|
|
IDX_RTL8100 equ 4
|
|
IDX_RTL8139D equ 5
|
|
IDX_RTL8139D equ 6
|
|
IDX_RTL8101 equ 7
|
|
|
|
ISR_SERR equ 1 SHL 15
|
|
ISR_TIMEOUT equ 1 SHL 14
|
|
ISR_LENCHG equ 1 SHL 13
|
|
ISR_FIFOOVW equ 1 SHL 6
|
|
ISR_PUN equ 1 SHL 5
|
|
ISR_RXOVW equ 1 SHL 4
|
|
ISR_TER equ 1 SHL 3
|
|
ISR_TOK equ 1 SHL 2
|
|
ISR_RER equ 1 SHL 1
|
|
ISR_ROK equ 1 SHL 0
|
|
|
|
INTERRUPT_MASK equ ISR_ROK or \
|
|
ISR_RXOVW or \
|
|
ISR_PUN or \
|
|
ISR_FIFOOVW or \
|
|
ISR_LENCHG or \
|
|
ISR_TOK or \
|
|
ISR_TER
|
|
|
|
TSR_OWN equ 1 SHL 13
|
|
TSR_TUN equ 1 SHL 14
|
|
TSR_TOK equ 1 SHL 15
|
|
|
|
TSR_CDH equ 1 SHL 28
|
|
TSR_OWC equ 1 SHL 29
|
|
TSR_TABT equ 1 SHL 30
|
|
TSR_CRS equ 1 SHL 31
|
|
|
|
|
|
|
|
section '.flat' code readable align 16
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; proc START ;;
|
|
;; ;;
|
|
;; (standard driver proc) ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
proc START stdcall, state:dword
|
|
|
|
cmp [state], 1
|
|
jne .exit
|
|
|
|
.entry:
|
|
|
|
DEBUGF 1,"Loading rtl8139 driver\n"
|
|
stdcall RegService, my_service, service_proc
|
|
ret
|
|
|
|
.fail:
|
|
.exit:
|
|
xor eax, eax
|
|
ret
|
|
|
|
endp
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; proc SERVICE_PROC ;;
|
|
;; ;;
|
|
;; (standard driver proc) ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
proc service_proc stdcall, ioctl:dword
|
|
|
|
mov edx, [ioctl]
|
|
mov eax, [edx+IOCTL.io_code]
|
|
|
|
;------------------------------------------------------
|
|
|
|
cmp eax, 0 ;SRV_GETVERSION
|
|
jne @F
|
|
|
|
cmp [edx+IOCTL.out_size], 4
|
|
jl .fail
|
|
mov eax, [edx+IOCTL.output]
|
|
mov [eax], dword API_VERSION
|
|
|
|
xor eax, eax
|
|
ret
|
|
|
|
;------------------------------------------------------
|
|
@@:
|
|
cmp eax, 1 ;SRV_HOOK
|
|
jne .fail
|
|
|
|
cmp [edx + IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
|
jl .fail
|
|
|
|
mov eax, [edx + IOCTL.input]
|
|
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
|
jne .fail ; other types arent supported for this card yet
|
|
|
|
; check if the device is already listed
|
|
|
|
mov esi, RTL8139_LIST
|
|
mov ecx, [RTL8139_DEV]
|
|
test ecx, ecx
|
|
jz .firstdevice
|
|
; mov eax, [edx+IOCTL.input] ; get the pci bus and device numbers
|
|
mov bx , [eax+1] ;
|
|
.nextdevice:
|
|
lodsd
|
|
cmp bx , word [eax + device.pci_bus] ; compare with pci and device num in RTL8139 list (notice the usage of word instead of byte)
|
|
je .find_devicenum ; Device is already loaded, let's find it's device number
|
|
|
|
loop .nextdevice
|
|
|
|
; This device doesnt have its own eth_device structure yet, lets create one
|
|
.firstdevice:
|
|
cmp [RTL8139_DEV], MAX_RTL8139 ; First check if the driver can handle one more card
|
|
jge .fail
|
|
|
|
push edx
|
|
stdcall KernelAlloc, dword device.size ; Allocate the buffer for eth_device structure
|
|
pop edx
|
|
test eax, eax
|
|
jz .fail
|
|
mov ebx, eax ; ebx is always used as a pointer to the structure (in driver, but also in kernel code)
|
|
|
|
; Fill in the direct call addresses into the struct
|
|
|
|
mov dword [ebx+device.reset], reset
|
|
mov dword [ebx+device.transmit], transmit
|
|
mov dword [ebx+device.get_MAC], read_mac
|
|
mov dword [ebx+device.set_MAC], write_mac
|
|
mov dword [ebx+device.unload], unload
|
|
mov dword [ebx+device.name], my_service
|
|
|
|
; save the pci bus and device numbers
|
|
|
|
mov eax, [edx+IOCTL.input]
|
|
mov cl , [eax+1]
|
|
mov [ebx+device.pci_bus], cl
|
|
mov cl , [eax+2]
|
|
mov [ebx+device.pci_dev], cl
|
|
|
|
; Now, it's time to find the base io addres of the PCI device
|
|
; TODO: implement check if bus and dev exist on this machine
|
|
|
|
mov edx, PCI_BASE_ADDRESS_0
|
|
.reg_check:
|
|
movzx eax, byte [ebx+device.pci_bus]
|
|
movzx ecx, byte [ebx+device.pci_dev]
|
|
|
|
push edx ecx
|
|
stdcall PciRead16, eax ,ecx ,edx
|
|
pop ecx edx
|
|
|
|
mov [ebx+device.io_addr], eax
|
|
and eax, PCI_BASE_ADDRESS_IO_MASK
|
|
test eax, eax
|
|
jz .inc_reg
|
|
mov eax, [ebx+device.io_addr]
|
|
and eax, PCI_BASE_ADDRESS_SPACE_IO
|
|
test eax, eax
|
|
jz .inc_reg
|
|
|
|
mov eax, [ebx+device.io_addr]
|
|
and eax, PCI_BASE_ADDRESS_IO_MASK
|
|
mov [ebx+device.io_addr], eax
|
|
jmp .got_io
|
|
|
|
.inc_reg:
|
|
add edx, 4
|
|
cmp edx, PCI_BASE_ADDRESS_5
|
|
jbe .reg_check
|
|
|
|
.got_io:
|
|
|
|
; We've found the io address, find IRQ now
|
|
|
|
movzx eax, byte [ebx+device.pci_bus]
|
|
movzx ecx, byte [ebx+device.pci_dev]
|
|
push ebx
|
|
stdcall PciRead8, eax ,ecx ,0x3c ; 0x3c is the offset where irq can be found
|
|
pop ebx
|
|
mov byte [ebx+device.irq_line], al
|
|
|
|
DEBUGF 1,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\
|
|
[ebx+device.pci_dev]:1,[ebx+device.pci_bus]:1,[ebx+device.irq_line]:1,[ebx+device.io_addr]:4
|
|
|
|
; Allocate the Receive buffer
|
|
|
|
stdcall KernelAlloc, dword (RX_BUFFER_SIZE+MAX_ETH_FRAME_SIZE)
|
|
test eax, eax
|
|
jz .err
|
|
mov [ebx+device.rx_buffer], eax ; Save the address to it into the device struct
|
|
|
|
; Now, Clear the allocated buffer
|
|
|
|
cld
|
|
mov edi, eax
|
|
mov ecx, (RX_BUFFER_SIZE)/4 ; divide by 4 because we are going to use DWORD
|
|
xor eax, eax
|
|
rep stosd
|
|
|
|
; Allocate the Transmit Buffer
|
|
|
|
stdcall KernelAlloc, dword (TX_BUF_SIZE*NUM_TX_DESC)
|
|
test eax, eax
|
|
jz .err
|
|
mov [ebx+device.tx_buffer], eax
|
|
|
|
; This one needs to be cleared too..
|
|
|
|
mov edi, eax
|
|
mov ecx, (TX_BUF_SIZE*NUM_TX_DESC)/4
|
|
xor eax, eax
|
|
rep stosd
|
|
|
|
; Ok, the eth_device structure is ready, let's probe the device
|
|
|
|
call probe ; this function will output in eax
|
|
test eax, eax
|
|
jnz .err ; If an error occured, exit
|
|
|
|
mov eax, [RTL8139_DEV] ; Add the device structure to our device list
|
|
mov [RTL8139_LIST+4*eax], ebx ; (IRQ handler uses this list to find device)
|
|
inc [RTL8139_DEV] ;
|
|
|
|
|
|
call EthRegDev
|
|
cmp eax, -1
|
|
je .destroy
|
|
|
|
ret
|
|
|
|
; If the device was already loaded, find the device number and return it in eax
|
|
|
|
.find_devicenum:
|
|
DEBUGF 1,"Trying to find device number of already registered device\n"
|
|
mov ebx, eax
|
|
call EthStruc2Dev ; This kernel procedure converts a pointer to device struct in ebx
|
|
; into a device number in edi
|
|
mov eax, edi ; Application wants it in eax instead
|
|
DEBUGF 1,"Kernel says: %u\n", eax
|
|
ret
|
|
|
|
; If an error occured, remove all allocated data and exit (returning -1 in eax)
|
|
|
|
.destroy:
|
|
; todo: reset device into virgin state
|
|
|
|
.err:
|
|
stdcall KernelFree, dword [ebx+device.rx_buffer]
|
|
stdcall KernelFree, dword [ebx+device.tx_buffer]
|
|
stdcall KernelFree, ebx
|
|
|
|
|
|
.fail:
|
|
or eax, -1
|
|
ret
|
|
|
|
;------------------------------------------------------
|
|
endp
|
|
|
|
|
|
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
|
|
;; ;;
|
|
;; Actual Hardware dependent code starts here ;;
|
|
;; ;;
|
|
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
|
|
|
|
align 4
|
|
unload:
|
|
; TODO: (in this particular order)
|
|
;
|
|
; - Stop the device
|
|
; - Detach int handler
|
|
; - Remove device from local list (RTL8139_LIST)
|
|
; - call unregister function in kernel
|
|
; - Remove all allocated structures and buffers the card used
|
|
|
|
or eax,-1
|
|
|
|
ret
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;;
|
|
;; probe: enables the device (if it really is RTL8139)
|
|
;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
probe:
|
|
DEBUGF 2,"Probing rtl8139 device: "
|
|
|
|
; enable the device
|
|
|
|
movzx eax, byte [ebx+device.pci_bus]
|
|
movzx ecx, byte [ebx+device.pci_dev]
|
|
stdcall PciRead32, eax ,ecx ,PCI_REG_CMD
|
|
|
|
mov cx , ax
|
|
or cl , (1 shl PCI_BIT_MASTER) or (1 shl PCI_BIT_PIO)
|
|
and cl , not (1 shl PCI_BIT_MMIO)
|
|
movzx eax, byte [ebx+device.pci_bus]
|
|
movzx edx, byte [ebx+device.pci_dev]
|
|
stdcall PciWrite32, eax ,edx ,PCI_REG_CMD, ecx
|
|
|
|
; get chip version
|
|
|
|
mov edx, [ebx+device.io_addr]
|
|
add edx, REG_TXCONFIG + 2
|
|
in ax , dx
|
|
shr ah , 2
|
|
shr ax , 6
|
|
and al , 01111111b
|
|
mov ecx, HW_VER_ARRAY_SIZE-1
|
|
.chip_ver_loop:
|
|
cmp al , [hw_ver_array+ecx]
|
|
je .chip_ver_found
|
|
dec ecx
|
|
jns .chip_ver_loop
|
|
xor cl , cl ; default RTL8139
|
|
.chip_ver_found:
|
|
mov [ebx+device.hw_ver_id], cl
|
|
|
|
shl ecx, 2
|
|
add ecx, name_crosslist
|
|
mov ecx, [ecx]
|
|
mov dword [ebx+device.name], ecx
|
|
|
|
DEBUGF 1,"Chip version: %s\n",ecx
|
|
|
|
; wake up the chip
|
|
|
|
mov edx, [ebx+device.io_addr]
|
|
add edx, REG_HLTCLK
|
|
mov al , 'R' ; run the clock
|
|
out dx , al
|
|
|
|
; unlock config and BMCR registers
|
|
|
|
add edx, REG_9346CR - REG_HLTCLK
|
|
mov al , (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EEM0)
|
|
out dx , al
|
|
|
|
; enable power management
|
|
|
|
add edx, REG_CONFIG1 - REG_9346CR
|
|
in al , dx
|
|
cmp byte [ebx+device.hw_ver_id], IDX_RTL8139B
|
|
jl .old_chip
|
|
|
|
; set LWAKE pin to active high (default value).
|
|
; it is for Wake-On-LAN functionality of some motherboards.
|
|
; this signal is used to inform the motherboard to execute a wake-up process.
|
|
; only at newer chips.
|
|
|
|
or al , (1 shl BIT_PMEn)
|
|
and al , not (1 shl BIT_LWACT)
|
|
out dx , al
|
|
add edx, REG_CONFIG4 - REG_CONFIG1
|
|
in al , dx
|
|
and al , not (1 shl BIT_LWPTN)
|
|
out dx , al
|
|
jmp .finish_wake_up
|
|
.old_chip:
|
|
|
|
; wake up older chips
|
|
|
|
and al , not ((1 shl BIT_SLEEP) or (1 shl BIT_PWRDWN))
|
|
out dx , al
|
|
.finish_wake_up:
|
|
|
|
; lock config and BMCR registers
|
|
|
|
xor al , al
|
|
mov edx, [ebx+device.io_addr]
|
|
add edx, REG_9346CR
|
|
out dx , al
|
|
DEBUGF 2,"done!\n"
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;;
|
|
;; reset: Set up all registers and descriptors, clear some values
|
|
;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
reset:
|
|
DEBUGF 2,"Resetting rtl8139: "
|
|
|
|
; attach int handler
|
|
|
|
movzx eax, [ebx+device.irq_line]
|
|
DEBUGF 1,"Attaching int handler to irq %x, ",eax:1
|
|
stdcall AttachIntHandler, eax, int_handler, dword 0
|
|
test eax, eax
|
|
jnz @f
|
|
DEBUGF 1,"\nCould not attach int handler!\n"
|
|
; or eax, -1
|
|
; ret
|
|
@@:
|
|
|
|
; reset chip
|
|
|
|
DEBUGF 1,"Resetting chip\n"
|
|
mov edx, [ebx+device.io_addr]
|
|
add edx, REG_COMMAND
|
|
mov al , 1 shl BIT_RST
|
|
out dx , al
|
|
mov cx , 1000 ; wait no longer for the reset
|
|
.wait_for_reset:
|
|
in al , dx
|
|
test al , 1 shl BIT_RST
|
|
jz .reset_completed ; RST remains 1 during reset
|
|
dec cx
|
|
jns .wait_for_reset
|
|
.reset_completed:
|
|
|
|
; unlock config and BMCR registers
|
|
|
|
mov edx, [ebx+device.io_addr]
|
|
add edx, REG_9346CR
|
|
mov al , (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EEM0)
|
|
out dx , al
|
|
|
|
; initialize multicast registers (no filtering)
|
|
|
|
mov eax, 0xffffffff
|
|
add edx, REG_MAR0 - REG_9346CR
|
|
out dx , eax
|
|
add edx, REG_MAR4 - REG_MAR0
|
|
out dx , eax
|
|
|
|
; enable Rx/Tx
|
|
|
|
mov al , (1 shl BIT_RE) or (1 shl BIT_TE)
|
|
add edx, REG_COMMAND - REG_MAR4
|
|
out dx , al
|
|
|
|
; 32k Rxbuffer, unlimited dma burst, no wrapping, no rx threshold
|
|
; accept broadcast packets, accept physical match packets
|
|
|
|
mov ax , RX_CONFIG
|
|
add edx, REG_RXCONFIG - REG_COMMAND
|
|
out dx , ax
|
|
|
|
; 1024 bytes DMA burst, total retries = 16 + 8 * 16 = 144
|
|
|
|
mov eax , (TX_MXDMA shl BIT_TX_MXDMA) or (TXRR shl BIT_TXRR) or BIT_IFG1 or BIT_IFG0
|
|
add edx, REG_TXCONFIG - REG_RXCONFIG
|
|
out dx , eax
|
|
|
|
; enable auto negotiation
|
|
|
|
add edx, REG_BMCR - REG_TXCONFIG
|
|
in ax , dx
|
|
or ax , (1 shl BIT_ANE)
|
|
out dx , ax
|
|
|
|
; set auto negotiation advertisement
|
|
|
|
add edx, REG_ANAR - REG_BMCR
|
|
in ax , dx
|
|
or ax , (1 shl BIT_SELECTOR) or (1 shl BIT_10) or (1 shl BIT_10FD) or (1 shl BIT_TX) or (1 shl BIT_TXFD)
|
|
out dx , ax
|
|
|
|
; lock config and BMCR registers
|
|
|
|
xor eax, eax
|
|
add edx, REG_9346CR - REG_ANAR
|
|
out dx , al
|
|
|
|
; init RX/TX pointers
|
|
|
|
mov [ebx+device.rx_data_offset], eax
|
|
mov [ebx+device.curr_tx_desc], al
|
|
|
|
; clear packet/byte counters
|
|
|
|
lea edi, [ebx+device.bytes_tx] ; TODO: check if destroying edi, ecx doesnt harm anything
|
|
mov ecx, 6
|
|
rep stosd
|
|
|
|
; clear missing packet counter
|
|
|
|
add edx, REG_MPC - REG_9346CR
|
|
out dx , eax
|
|
|
|
; Set up the 4 Txbuffer descriptors
|
|
|
|
add edx, REG_TSAD0 - REG_MPC
|
|
mov eax, [ebx+device.tx_buffer]
|
|
mov ecx, 4
|
|
.loop:
|
|
push eax
|
|
call GetPgAddr
|
|
DEBUGF 2,"Desc: %x ", eax
|
|
out dx , eax
|
|
add dx , 4
|
|
pop eax
|
|
add eax, TX_BUF_SIZE
|
|
loop .loop
|
|
|
|
; set RxBuffer address, init RX buffer offset, init TX ring
|
|
|
|
mov eax, [ebx+device.rx_buffer]
|
|
call GetPgAddr
|
|
mov edx, [ebx+device.io_addr]
|
|
add edx, REG_RBSTART
|
|
out dx , eax
|
|
|
|
; enable interrupts
|
|
|
|
mov eax, INTERRUPT_MASK
|
|
add edx, REG_IMR - REG_RBSTART
|
|
out dx , ax
|
|
|
|
; Read MAC address
|
|
|
|
call read_mac
|
|
|
|
; Indicate that we have successfully reset the card
|
|
|
|
DEBUGF 2,"Done!\n"
|
|
xor eax, eax
|
|
|
|
ret
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; Transmit ;;
|
|
;; ;;
|
|
;; In: buffer pointer in [esp+4] ;;
|
|
;; size of buffer in [esp+8] ;;
|
|
;; pointer to device structure in ebx ;;
|
|
;; ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
transmit:
|
|
DEBUGF 1,"Transmitting packet, buffer:%x, size:%u\n",[esp+4],[esp+8]
|
|
mov eax, [esp+4]
|
|
DEBUGF 1,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\
|
|
[eax+00]:2,[eax+01]:2,[eax+02]:2,[eax+03]:2,[eax+04]:2,[eax+05]:2,\
|
|
[eax+06]:2,[eax+07]:2,[eax+08]:2,[eax+09]:2,[eax+10]:2,[eax+11]:2,\
|
|
[eax+13]:2,[eax+12]:2
|
|
|
|
cmp dword [esp+8], MAX_ETH_FRAME_SIZE
|
|
jg .finish ; packet is too long
|
|
cmp dword [esp+8], 60
|
|
jl .finish ; packet is too short
|
|
|
|
; check descriptor
|
|
; DEBUGF 1,"Checking descriptor, "
|
|
movzx ecx, [ebx+device.curr_tx_desc]
|
|
mov edx, [ebx+device.io_addr]
|
|
lea edx, [edx+ecx*4+REG_TSD0]
|
|
in ax, dx
|
|
test ax, 0x1fff ; or no size given
|
|
jz .send_packet
|
|
and ax, (1 shl BIT_TOK) or (1 shl BIT_OWN)
|
|
cmp ax, (1 shl BIT_TOK) or (1 shl BIT_OWN)
|
|
jz .send_packet
|
|
; wait for timeout
|
|
; DEBUGF 1,"Waiting for timeout, "
|
|
|
|
push edx ebx ; TODO : rtl8139 internal timer should be used instead
|
|
stdcall Sleep, TX_TIMEOUT ; ? What registers does this destroy ?
|
|
pop ebx edx
|
|
|
|
in ax, dx
|
|
and ax, (1 shl BIT_TOK) or (1 shl BIT_OWN)
|
|
cmp ax, (1 shl BIT_TOK) or (1 shl BIT_OWN)
|
|
jz .send_packet ; if chip hung, reset it
|
|
push dx
|
|
call reset ; reset the card
|
|
pop dx
|
|
.send_packet:
|
|
; DEBUGF 1,"Sending packet, "
|
|
|
|
push edx
|
|
movzx eax, [ebx+device.curr_tx_desc] ; calculate the current tx_buffer address
|
|
mov edx, TX_BUF_SIZE ;MAX_ETH_FRAME_SIZE ;
|
|
mul edx ;
|
|
mov edi, [ebx+device.tx_buffer] ;
|
|
add edi, eax ; Store it in edi
|
|
pop edx
|
|
|
|
mov esi, [esp+4] ; Copy data to that address
|
|
mov ecx, [esp+8] ;
|
|
shr ecx, 2 ;
|
|
rep movsd ;
|
|
mov ecx, [esp+8] ;
|
|
and ecx, 3 ;
|
|
rep movsb ;
|
|
|
|
inc [ebx+device.packets_tx] ;
|
|
mov eax, [esp+8] ; Get packet size in eax
|
|
|
|
add dword [ebx + device.bytes_tx], eax
|
|
adc dword [ebx + device.bytes_tx + 4], 0
|
|
|
|
; or eax, (ERTXTH shl BIT_ERTXTH) ; Set descriptor size and the early tx treshold into the correct Transmission status register (TSD0, TSD1, TSD2 or TSD3)
|
|
out dx , eax ;
|
|
|
|
; get next descriptor 0, 1, 2, 3, 0, 1, 2, 3, 0, 1, ...
|
|
inc [ebx+device.curr_tx_desc]
|
|
and [ebx+device.curr_tx_desc], 3
|
|
|
|
DEBUGF 2," - Packet Sent! "
|
|
.finish:
|
|
DEBUGF 2," - Done!\n"
|
|
ret
|
|
|
|
|
|
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; Interrupt handler ;;
|
|
;; ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
int_handler:
|
|
|
|
DEBUGF 1,"IRQ %x ",eax:2 ; no, you cant replace 'eax:2' with 'al', this must be a bug in FDO
|
|
|
|
; find pointer of device wich made IRQ occur
|
|
|
|
mov esi, RTL8139_LIST
|
|
mov ecx, [RTL8139_DEV]
|
|
.nextdevice:
|
|
mov ebx, dword [esi]
|
|
|
|
mov edx, dword [ebx+device.io_addr] ; get IRQ reason
|
|
add edx, REG_ISR
|
|
in ax , dx
|
|
out dx , ax ; send it back to ACK
|
|
|
|
add esi, 4
|
|
|
|
test ax , ax
|
|
jnz .got_it
|
|
|
|
loop .nextdevice
|
|
|
|
ret ; If no device was found, abort (The irq was probably for a device, not registered to this driver)
|
|
|
|
.got_it:
|
|
|
|
; looks like we've found it!
|
|
|
|
; Lets found out why the irq occured then..
|
|
|
|
;----------------------------------------------------
|
|
; Received packet ok?
|
|
|
|
test ax, ISR_ROK
|
|
jz @f
|
|
push ax
|
|
|
|
.receive:
|
|
mov edx, dword [ebx+device.io_addr] ; get IRQ reason
|
|
add edx, REG_COMMAND ;
|
|
in al , dx ;
|
|
test al , BUFE ; test if RX buffer is empty
|
|
jnz .finish ;
|
|
|
|
DEBUGF 2,"RX: "
|
|
|
|
mov eax, dword [ebx+device.rx_buffer]
|
|
add eax, dword [ebx+device.rx_data_offset]
|
|
test byte [eax], (1 shl BIT_ROK) ; check if packet is ok
|
|
jz .reset_rx
|
|
; packet is ok, copy it
|
|
movzx ecx, word [eax+2] ; packet length
|
|
add dword [ebx + device.bytes_rx], ecx ; Update stats
|
|
adc dword [ebx + device.bytes_rx + 4], 0
|
|
inc dword [ebx + device.packets_rx] ;
|
|
sub ecx, 4 ; don't copy CRC
|
|
DEBUGF 1,"Received %u bytes\n", ecx
|
|
|
|
push ebx eax ecx
|
|
stdcall KernelAlloc, ecx ; Allocate a buffer to put packet into
|
|
pop ecx
|
|
test eax, eax ; Test if we allocated succesfully
|
|
jz .abort ;
|
|
|
|
mov edi, eax ; Set up registers to copy the packet
|
|
mov esi, [esp] ;
|
|
add esi, 4 ; Dont copy CRC
|
|
|
|
push dword .abort ; Kernel will return to this address after EthReceiver
|
|
push ecx edi ; Save buffer pointer and size, to pass to kernel
|
|
|
|
shr ecx, 2
|
|
cld
|
|
rep movsd ; copy the dwords
|
|
mov ecx, [esp+4]
|
|
and ecx, 3
|
|
rep movsb ; copy the rest bytes
|
|
|
|
jmp EthReceiver ; Send it to kernel
|
|
|
|
.abort:
|
|
pop eax ebx
|
|
; update eth_data_start_offset
|
|
movzx eax, word [eax+2] ; packet length
|
|
add eax, [ebx+device.rx_data_offset]
|
|
add eax, 4+3 ; packet header is 4 bytes long + dword alignment
|
|
and eax, not 3 ; dword alignment
|
|
cmp eax, RX_BUFFER_SIZE
|
|
jl .no_wrap
|
|
sub eax, RX_BUFFER_SIZE
|
|
.no_wrap:
|
|
mov [ebx+device.rx_data_offset], eax
|
|
DEBUGF 1,"New RX ptr: %u", eax
|
|
|
|
mov edx, dword [ebx+device.io_addr]
|
|
add edx, REG_CAPR ; update 'Current Address of Packet Read register'
|
|
sub eax, 0x10 ; value 0x10 is a constant for CAPR
|
|
out dx , ax
|
|
|
|
jmp .receive ; check for multiple packets
|
|
|
|
.reset_rx:
|
|
test byte [eax], (1 shl BIT_CRC)
|
|
jz .no_crc_error
|
|
DEBUGF 2,"\nCRC error!\n"
|
|
|
|
.no_crc_error:
|
|
test byte [eax], (1 shl BIT_FAE)
|
|
jz .no_fae_error
|
|
DEBUGF 1,"\nFrame alignment error!\n"
|
|
|
|
.no_fae_error:
|
|
DEBUGF 1,"Reset RX\n"
|
|
in al , dx ; read command register
|
|
push ax
|
|
|
|
and al , not (1 shl BIT_RE) ; Clear the RE bit
|
|
out dx , al
|
|
|
|
pop ax
|
|
out dx , al ; write original command back
|
|
|
|
add edx, REG_RXCONFIG - REG_COMMAND ; Restore RX configuration
|
|
mov ax , RX_CONFIG
|
|
out dx , ax
|
|
|
|
.finish:
|
|
pop ax
|
|
|
|
;----------------------------------------------------
|
|
; Transmit error ?
|
|
|
|
@@:
|
|
test ax, ISR_TER
|
|
jz @f
|
|
|
|
push ax
|
|
cmp [ebx+device.curr_tx_desc], 4
|
|
jz .notxd
|
|
|
|
mov edx, [ebx+device.io_addr]
|
|
movzx ecx, [ebx+device.curr_tx_desc]
|
|
lea edx, [edx+ecx*4+REG_TSD0]
|
|
in eax, dx
|
|
|
|
.notxd:
|
|
test eax, TSR_TUN
|
|
jz .nobun
|
|
DEBUGF 1, "TX: FIFO Buffer underrun!\n"
|
|
|
|
.nobun:
|
|
test eax, TSR_OWC
|
|
jz .noowc
|
|
DEBUGF 1, "TX: OWC!\n"
|
|
|
|
.noowc:
|
|
test eax, TSR_TABT
|
|
jz .notabt
|
|
DEBUGF 1, "TX: TABT!\n"
|
|
|
|
.notabt:
|
|
test eax, TSR_CRS
|
|
jz .nocsl
|
|
DEBUGF 1, "TX: Carrier Sense Lost!\n"
|
|
|
|
.nocsl:
|
|
; test eax, TSR_OWN or TSR_TOK
|
|
; jz .nofd
|
|
; DEBUGF 1, "TX: Transmit OK (desc: %u)\n", ecx
|
|
;
|
|
; .nofd:
|
|
pop ax
|
|
|
|
;----------------------------------------------------
|
|
; Transmit ok ?
|
|
|
|
@@:
|
|
test ax, ISR_TOK
|
|
jz @f
|
|
|
|
DEBUGF 1, "TX: Transmit OK (desc: %u)\n", [ebx+device.curr_tx_desc]:1
|
|
|
|
;----------------------------------------------------
|
|
; Rx buffer overflow ?
|
|
|
|
@@:
|
|
test ax, ISR_RXOVW
|
|
jz @f
|
|
|
|
push ax
|
|
DEBUGF 1,"RX-buffer overflow!\n"
|
|
|
|
mov edx, [ebx+device.io_addr]
|
|
add edx, REG_ISR
|
|
mov ax , ISR_FIFOOVW or ISR_RXOVW
|
|
out dx , ax
|
|
pop ax
|
|
|
|
;----------------------------------------------------
|
|
; Packet underrun? ?
|
|
|
|
|
|
@@:
|
|
test ax, ISR_PUN
|
|
jz @f
|
|
|
|
DEBUGF 1,"Packet underrun!\n"
|
|
|
|
;----------------------------------------------------
|
|
; Receive FIFO overflow ?
|
|
|
|
@@:
|
|
test ax, ISR_FIFOOVW
|
|
jz @f
|
|
|
|
push ax
|
|
DEBUGF 2,"RX fifo overflox!\n"
|
|
|
|
mov edx, [ebx+device.io_addr]
|
|
add edx, REG_ISR
|
|
mov ax , ISR_FIFOOVW or ISR_RXOVW
|
|
out dx , ax
|
|
pop ax
|
|
|
|
;----------------------------------------------------
|
|
; Something about Cable changed ?
|
|
|
|
@@:
|
|
test ax, ISR_LENCHG
|
|
jz .fail
|
|
|
|
DEBUGF 2,"Cable changed!\n"
|
|
call cable
|
|
|
|
; If none of the above events happened, just exit clearing int
|
|
|
|
.fail:
|
|
|
|
DEBUGF 2,"\n"
|
|
ret
|
|
|
|
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; Update Cable status ;;
|
|
;; ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
cable:
|
|
DEBUGF 1,"Checking Cable status: "
|
|
|
|
mov edx, dword [ebx+device.io_addr]
|
|
add edx, REG_MSR
|
|
in al , dx
|
|
|
|
; test al , 1 SHL 2 ; 0 = link ok 1 = link fail
|
|
; jnz .notconnected
|
|
|
|
; test al , 1 SHL 3 ; 0 = 100 Mbps 1 = 10 Mbps
|
|
; jnz .10mbps
|
|
|
|
shr al, 2
|
|
and al, 3
|
|
|
|
mov byte [ebx+device.mode+3], al
|
|
DEBUGF 1,"Done!\n"
|
|
ret
|
|
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; Write MAC address ;;
|
|
;; ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
write_mac: ; in: mac pushed onto stack (as 3 words)
|
|
|
|
DEBUGF 1,"Writing MAC: "
|
|
|
|
; disable all in command registers
|
|
|
|
mov edx, [ebx+device.io_addr]
|
|
add edx, REG_9346CR
|
|
xor eax, eax
|
|
out dx , al
|
|
|
|
add edx, REG_IMR - REG_9346CR
|
|
xor eax, eax
|
|
out dx , ax
|
|
|
|
add edx, REG_ISR - REG_IMR
|
|
mov eax, -1
|
|
out dx , ax
|
|
|
|
; enable writing
|
|
|
|
|
|
add edx, REG_9346CR - REG_ISR
|
|
mov eax, REG_9346CR_WE
|
|
out dx , al
|
|
|
|
; write the mac ...
|
|
|
|
add edx, REG_IDR0 - REG_9346CR
|
|
pop eax
|
|
out dx , eax
|
|
|
|
add edx, 4
|
|
xor eax, eax
|
|
pop ax
|
|
out dx , eax
|
|
|
|
; disable writing
|
|
|
|
add edx, REG_9346CR -REG_IDR0
|
|
xor eax, eax
|
|
out dx , al
|
|
|
|
DEBUGF 1,"ok!\n"
|
|
|
|
; Notice this procedure does not ret, but continues to read_mac instead.
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; Read MAC address ;;
|
|
;; ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
read_mac:
|
|
DEBUGF 1,"Reading MAC: "
|
|
|
|
mov edx, [ebx + device.io_addr]
|
|
lea edi, [ebx + device.mac]
|
|
in eax, dx
|
|
stosd
|
|
add edx, 4
|
|
in ax, dx
|
|
stosw
|
|
|
|
DEBUGF 1,"%x-%x-%x-%x-%x-%x\n",[edi-6]:2,[edi-5]:2,[edi-4]:2,[edi-3]:2,[edi-2]:2,[edi-1]:2
|
|
|
|
ret
|
|
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; Read eeprom (type 93c46 and 93c56) ;;
|
|
;; ;;
|
|
;; In: word to be read in al (6bit in case of 93c46 and 8bit otherwise) ;;
|
|
;; pointer to device structure in ebx ;;
|
|
;; ;;
|
|
;; OUT: word read in ax ;;
|
|
;; ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
read_eeprom:
|
|
DEBUGF 2,"Reading eeprom, "
|
|
|
|
mov edx, [ebx+device.io_addr]
|
|
push ebx
|
|
movzx ebx, al
|
|
add edx, REG_RXCONFIG
|
|
in al, dx
|
|
test al, (1 shl BIT_9356SEL)
|
|
jz .type_93c46
|
|
; and bl, 01111111b ; don't care first bit
|
|
or bx, EE_93C56_READ_CMD ; it contains start bit
|
|
mov cx, EE_93C56_CMD_LENGTH-1 ; cmd_loop counter
|
|
jmp .read_eeprom
|
|
.type_93c46:
|
|
and bl, 00111111b
|
|
or bx, EE_93C46_READ_CMD ; it contains start bit
|
|
mov cx, EE_93C46_CMD_LENGTH-1 ; cmd_loop counter
|
|
.read_eeprom:
|
|
add edx, REG_9346CR - REG_RXCONFIG
|
|
; mov al, (1 shl BIT_93C46_EEM1)
|
|
; out dx, al
|
|
mov al, (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EECS) ; wake up the eeprom
|
|
out dx, al
|
|
.cmd_loop:
|
|
mov al, (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EECS)
|
|
bt bx, cx
|
|
jnc .zero_bit
|
|
or al, (1 shl BIT_93C46_EEDI)
|
|
.zero_bit:
|
|
out dx, al
|
|
; push eax
|
|
; in eax, dx ; eeprom delay
|
|
; pop eax
|
|
or al, (1 shl BIT_93C46_EESK)
|
|
out dx, al
|
|
; in eax, dx ; eeprom delay
|
|
dec cx
|
|
jns .cmd_loop
|
|
; in eax, dx ; eeprom delay
|
|
mov al, (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EECS)
|
|
out dx, al
|
|
mov cl, 0xf
|
|
.read_loop:
|
|
shl ebx, 1
|
|
mov al, (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EECS) or (1 shl BIT_93C46_EESK)
|
|
out dx, al
|
|
; in eax, dx ; eeprom delay
|
|
in al, dx
|
|
and al, (1 shl BIT_93C46_EEDO)
|
|
jz .dont_set
|
|
inc ebx
|
|
.dont_set:
|
|
mov al, (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EECS)
|
|
out dx, al
|
|
; in eax, dx ; eeprom delay
|
|
dec cl
|
|
jns .read_loop
|
|
xor al, al
|
|
out dx, al
|
|
mov ax, bx
|
|
pop ebx
|
|
|
|
ret
|
|
|
|
|
|
; End of code
|
|
|
|
align 4 ; Place all initialised data here
|
|
|
|
RTL8139_DEV dd 0
|
|
version dd (5 shl 16) or (API_VERSION and 0xFFFF)
|
|
my_service db 'RTL8139',0 ; max 16 chars include zero
|
|
|
|
device_1 db 'Realtek 8139',0
|
|
device_2 db 'Realtek 8139A',0
|
|
device_3 db 'Realtek 8139B',0
|
|
device_4 db 'Realtek 8139C',0
|
|
device_5 db 'Realtek 8100',0
|
|
device_6 db 'Realtek 8139D',0
|
|
device_7 db 'Realtek 8139CP',0
|
|
device_8 db 'Realtek 8101',0
|
|
|
|
name_crosslist dd device_1
|
|
dd device_2
|
|
dd device_3
|
|
dd device_4
|
|
dd device_5
|
|
dd device_6
|
|
dd device_7
|
|
dd device_8
|
|
|
|
hw_ver_array db VER_RTL8139 ; This array is used by the probe routine to find out wich version of the RTL8139 we are working with
|
|
db VER_RTL8139A
|
|
db VER_RTL8139B
|
|
db VER_RTL8139C
|
|
db VER_RTL8100
|
|
db VER_RTL8139D
|
|
db VER_RTL8139CP
|
|
db VER_RTL8101
|
|
|
|
HW_VER_ARRAY_SIZE = $-hw_ver_array
|
|
|
|
include_debug_strings ; All data wich FDO uses will be included here
|
|
|
|
section '.data' data readable writable align 16 ; place all uninitialized data place here
|
|
|
|
RTL8139_LIST rd MAX_RTL8139 ; This list contains all pointers to device structures the driver is handling
|
|
|