forked from KolibriOS/kolibrios
1108 lines
20 KiB
NASM
1108 lines
20 KiB
NASM
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; Copyright (C) KolibriOS team 2004-2011. All rights reserved. ;;
|
|
;; Distributed under terms of the GNU General Public License ;;
|
|
;; ;;
|
|
;; i8255x (Intel eepro 100) driver for KolibriOS ;;
|
|
;; ;;
|
|
;; Written by hidnplayr@kolibrios.org ;;
|
|
;; ;;
|
|
;; GNU GENERAL PUBLIC LICENSE ;;
|
|
;; Version 2, June 1991 ;;
|
|
;; ;;
|
|
;; ;;
|
|
;; Good read about how to program this family of devices: ;;
|
|
;; http://www.intel.com/design/network/manuals/8255x_opensdm.htm ;;
|
|
;; ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
|
|
format MS COFF
|
|
|
|
API_VERSION equ 0x01000100
|
|
DRIVER_VERSION equ 5
|
|
|
|
MAX_DEVICES equ 16
|
|
|
|
DEBUG equ 1
|
|
__DEBUG__ equ 1
|
|
__DEBUG_LEVEL__ equ 1
|
|
|
|
include 'proc32.inc'
|
|
include 'imports.inc'
|
|
include 'fdo.inc'
|
|
include 'netdrv.inc'
|
|
|
|
public START
|
|
public service_proc
|
|
public version
|
|
|
|
virtual at ebx
|
|
|
|
device:
|
|
|
|
ETH_DEVICE
|
|
|
|
.io_addr dd ?
|
|
.pci_bus db ?
|
|
.pci_dev db ?
|
|
.irq_line db ?
|
|
|
|
.rx_buffer dd ?
|
|
.tx_buffer dd ?
|
|
|
|
.ee_bus_width dd ?
|
|
|
|
rb 5+8 ;;;; align
|
|
|
|
rxfd:
|
|
.status dw ?
|
|
.command dw ?
|
|
.link dd ?
|
|
.rx_buf_addr dd ?
|
|
.count dw ?
|
|
.size dw ?
|
|
.packet dd ?
|
|
|
|
rb 12 ;;;;
|
|
|
|
txfd:
|
|
.status dw ?
|
|
.command dw ?
|
|
.link dd ?
|
|
.tx_desc_addr dd ?
|
|
.count dd ?
|
|
.tx_buf_addr0 dd ?
|
|
.tx_buf_size0 dd ?
|
|
.tx_buf_addr1 dd ?
|
|
.tx_buf_size1 dd ?
|
|
|
|
confcmd:
|
|
.status: dw ?
|
|
.command: dw ?
|
|
.link: dd ?
|
|
.data rb 64
|
|
|
|
lstats:
|
|
tx_good_frames dd ?
|
|
tx_coll16_errs dd ?
|
|
tx_late_colls dd ?
|
|
tx_underruns dd ?
|
|
tx_lost_carrier dd ?
|
|
tx_deferred dd ?
|
|
tx_one_colls dd ?
|
|
tx_multi_colls dd ?
|
|
tx_total_colls dd ?
|
|
|
|
rx_good_frames dd ?
|
|
rx_crc_errs dd ?
|
|
rx_align_errs dd ?
|
|
rx_resource_errs dd ?
|
|
rx_overrun_errs dd ?
|
|
rx_colls_errs dd ?
|
|
rx_runt_errs dd ?
|
|
|
|
device_size = $ - device
|
|
|
|
end virtual
|
|
|
|
|
|
; Serial EEPROM
|
|
|
|
EE_SK equ 1 shl 16 ; serial clock
|
|
EE_CS equ 1 shl 17 ; chip select
|
|
EE_DI equ 1 shl 18 ; data in
|
|
EE_DO equ 1 shl 19 ; data out
|
|
|
|
EE_READ equ 110b
|
|
EE_WRITE equ 101b
|
|
EE_ERASE equ 111b
|
|
|
|
; The SCB accepts the following controls for the Tx and Rx units:
|
|
|
|
CU_START equ 0x0010
|
|
CU_RESUME equ 0x0020
|
|
CU_STATSADDR equ 0x0040
|
|
CU_SHOWSTATS equ 0x0050 ; Dump statistics counters.
|
|
CU_CMD_BASE equ 0x0060 ; Base address to add to add CU commands.
|
|
CU_DUMPSTATS equ 0x0070 ; Dump then reset stats counters.
|
|
|
|
RX_START equ 0x0001
|
|
RX_RESUME equ 0x0002
|
|
RX_ABORT equ 0x0004
|
|
RX_ADDR_LOAD equ 0x0006
|
|
RX_RESUMENR equ 0x0007
|
|
INT_MASK equ 0x0100
|
|
DRVR_INT equ 0x0200 ; Driver generated interrupt
|
|
|
|
CmdIASetup equ 0x0001
|
|
CmdConfigure equ 0x0002
|
|
CmdTx equ 0x0004 ;;;;
|
|
CmdTxFlex equ 0x0008 ;;;
|
|
Cmdsuspend equ 0x4000
|
|
|
|
|
|
reg_scb_status equ 0
|
|
reg_scb_cmd equ 2
|
|
reg_scb_ptr equ 4
|
|
reg_port equ 8
|
|
reg_eeprom_ctrl equ 12
|
|
reg_eeprom equ 14
|
|
reg_mdi_ctrl equ 16
|
|
|
|
|
|
macro delay {
|
|
push eax
|
|
in eax, dx
|
|
in eax, dx
|
|
in eax, dx
|
|
in eax, dx
|
|
in eax, dx
|
|
in eax, dx
|
|
in eax, dx
|
|
in eax, dx
|
|
in eax, dx
|
|
in eax, dx
|
|
pop eax
|
|
}
|
|
|
|
section '.flat' code readable align 16
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; proc START ;;
|
|
;; ;;
|
|
;; (standard driver proc) ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
proc START stdcall, state:dword
|
|
|
|
cmp [state], 1
|
|
jne .exit
|
|
|
|
.entry:
|
|
|
|
DEBUGF 1,"Loading i8255x driver\n"
|
|
stdcall RegService, my_service, service_proc
|
|
ret
|
|
|
|
.fail:
|
|
.exit:
|
|
xor eax, eax
|
|
ret
|
|
|
|
endp
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; proc SERVICE_PROC ;;
|
|
;; ;;
|
|
;; (standard driver proc) ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
proc service_proc stdcall, ioctl:dword
|
|
|
|
mov edx, [ioctl]
|
|
mov eax, [IOCTL.io_code]
|
|
|
|
;------------------------------------------------------
|
|
|
|
cmp eax, 0 ;SRV_GETVERSION
|
|
jne @F
|
|
|
|
cmp [IOCTL.out_size], 4
|
|
jl .fail
|
|
mov eax, [IOCTL.output]
|
|
mov [eax], dword API_VERSION
|
|
|
|
xor eax, eax
|
|
ret
|
|
|
|
;------------------------------------------------------
|
|
@@:
|
|
cmp eax, 1 ;SRV_HOOK
|
|
jne .fail
|
|
|
|
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
|
jl .fail
|
|
|
|
mov eax, [IOCTL.input]
|
|
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
|
jne .fail ; other types arent supported for this card yet
|
|
|
|
; check if the device is already listed
|
|
|
|
mov esi, device_list
|
|
mov ecx, [devices]
|
|
test ecx, ecx
|
|
jz .firstdevice
|
|
|
|
; mov eax, [IOCTL.input] ; get the pci bus and device numbers
|
|
mov ax , [eax+1] ;
|
|
.nextdevice:
|
|
mov ebx, [esi]
|
|
cmp ax , word [device.pci_bus] ; compare with pci and device num in device list (notice the usage of word instead of byte)
|
|
je .find_devicenum ; Device is already loaded, let's find it's device number
|
|
add esi, 4
|
|
loop .nextdevice
|
|
|
|
|
|
; This device doesnt have its own eth_device structure yet, lets create one
|
|
.firstdevice:
|
|
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
|
|
jge .fail
|
|
|
|
push edx
|
|
stdcall KernelAlloc, device_size
|
|
pop edx
|
|
test eax, eax
|
|
jz .fail
|
|
mov ebx, eax ; ebx is always used as a pointer to the structure (in driver, but also in kernel code)
|
|
|
|
; Fill in the direct call addresses into the struct
|
|
|
|
mov [device.reset], reset
|
|
mov [device.transmit], transmit
|
|
; mov [device.get_MAC], read_mac
|
|
mov [device.set_MAC], MAC_write
|
|
mov [device.unload], unload
|
|
mov [device.name], my_service
|
|
|
|
; save the pci bus and device numbers
|
|
|
|
mov eax, [IOCTL.input]
|
|
mov cl , [eax+1]
|
|
mov [device.pci_bus], cl
|
|
mov cl , [eax+2]
|
|
mov [device.pci_dev], cl
|
|
|
|
; Now, it's time to find the base io addres of the PCI device
|
|
|
|
find_io [device.pci_bus], [device.pci_dev], [device.io_addr]
|
|
|
|
; We've found the io address, find IRQ now
|
|
|
|
find_irq [device.pci_bus], [device.pci_dev], [device.irq_line]
|
|
|
|
DEBUGF 2,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\
|
|
[device.pci_dev]:1,[device.pci_bus]:1,[device.irq_line]:1,[device.io_addr]:4
|
|
|
|
allocate_and_clear [device.rx_buffer], (4096), .err
|
|
allocate_and_clear [device.tx_buffer], (4096), .err
|
|
|
|
; Ok, the eth_device structure is ready, let's probe the device
|
|
|
|
call probe ; this function will output in eax
|
|
test eax, eax
|
|
jnz .err ; If an error occured, exit
|
|
|
|
mov eax, [devices] ; Add the device structure to our device list
|
|
mov [device_list+4*eax], ebx ; (IRQ handler uses this list to find device)
|
|
inc [devices] ;
|
|
|
|
|
|
mov [device.type], NET_TYPE_ETH
|
|
call NetRegDev
|
|
|
|
cmp eax, -1
|
|
je .err
|
|
|
|
ret
|
|
|
|
; If the device was already loaded, find the device number and return it in eax
|
|
|
|
.find_devicenum:
|
|
DEBUGF 2,"Trying to find device number of already registered device\n"
|
|
call NetPtrToNum ; This kernel procedure converts a pointer to device struct in ebx
|
|
; into a device number in edi
|
|
mov eax, edi ; Application wants it in eax instead
|
|
DEBUGF 2,"Kernel says: %u\n", eax
|
|
ret
|
|
|
|
; If an error occured, remove all allocated data and exit (returning -1 in eax)
|
|
|
|
.err:
|
|
stdcall KernelFree, [device.rx_buffer]
|
|
stdcall KernelFree, [device.tx_buffer]
|
|
stdcall KernelFree, ebx
|
|
|
|
.fail:
|
|
or eax, -1
|
|
ret
|
|
|
|
;------------------------------------------------------
|
|
endp
|
|
|
|
|
|
|
|
|
|
|
|
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
|
|
;; ;;
|
|
;; Actual Hardware dependent code starts here ;;
|
|
;; ;;
|
|
;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;;
|
|
|
|
|
|
unload:
|
|
; TODO: (in this particular order)
|
|
;
|
|
; - Stop the device
|
|
; - Detach int handler
|
|
; - Remove device from local list (device_list)
|
|
; - call unregister function in kernel
|
|
; - Remove all allocated structures and buffers the card used
|
|
|
|
or eax,-1
|
|
|
|
ret
|
|
|
|
|
|
;-------------
|
|
;
|
|
; Probe
|
|
;
|
|
;-------------
|
|
|
|
align 4
|
|
probe:
|
|
|
|
DEBUGF 1,"Probing i8255x\n"
|
|
|
|
make_bus_master [device.pci_bus], [device.pci_dev]
|
|
|
|
;---------------------------
|
|
; First, identify the device
|
|
|
|
movzx ecx, [device.pci_bus]
|
|
movzx edx, [device.pci_dev]
|
|
stdcall PciRead32, ecx ,edx ,0 ; get device/vendor id
|
|
|
|
DEBUGF 1,"Vendor_id=0x%x\n", ax
|
|
|
|
cmp ax, 0x8086
|
|
jne .notfound
|
|
shr eax, 16
|
|
|
|
DEBUGF 1,"Device_id=0x%x\n", ax
|
|
|
|
mov ecx, DEVICE_IDs
|
|
mov edi, device_id_list
|
|
repne scasw
|
|
jne .notfound
|
|
jmp .found
|
|
|
|
.notfound:
|
|
DEBUGF 1,"ERROR: Unsupported device!\n"
|
|
or eax, -1
|
|
ret
|
|
|
|
.found:
|
|
|
|
call ee_get_width
|
|
call MAC_read_eeprom
|
|
|
|
;;; TODO: detect phy
|
|
|
|
|
|
|
|
;----------
|
|
;
|
|
; Reset
|
|
;
|
|
;----------
|
|
|
|
align 4
|
|
reset:
|
|
|
|
;---------------
|
|
; reset the card
|
|
|
|
set_io 0
|
|
set_io reg_port
|
|
xor eax, eax ; Software Reset
|
|
out dx, eax
|
|
|
|
mov esi, 10
|
|
call Sleep ; Give the card time to warm up.
|
|
|
|
;---------------------------------
|
|
; Tell device where to store stats
|
|
|
|
lea eax, [lstats]
|
|
GetRealAddr
|
|
set_io reg_scb_ptr
|
|
out dx, eax
|
|
|
|
mov ax, INT_MASK + CU_STATSADDR
|
|
set_io reg_scb_cmd
|
|
out dx, ax
|
|
call cmd_wait
|
|
|
|
;-----------------
|
|
; Set CU base to 0
|
|
|
|
xor eax, eax
|
|
set_io reg_scb_ptr
|
|
out dx, eax
|
|
|
|
mov ax, INT_MASK + RX_ADDR_LOAD
|
|
set_io reg_scb_cmd
|
|
out dx, ax
|
|
call cmd_wait
|
|
|
|
;---------------------
|
|
; build rxfd structure
|
|
|
|
mov ax, 0x0001
|
|
mov [rxfd.status], ax
|
|
mov ax, 0x0000
|
|
mov [rxfd.command], ax
|
|
|
|
lea eax, [rxfd.status]
|
|
GetRealAddr
|
|
mov [rxfd.link], eax
|
|
|
|
lea eax, [device.rx_buffer]
|
|
GetRealAddr
|
|
mov [rxfd.rx_buf_addr], eax
|
|
|
|
xor ax, ax
|
|
mov [rxfd.count], ax
|
|
|
|
mov ax, 1528
|
|
mov [rxfd.size], ax
|
|
|
|
;-------------------------------
|
|
; Set ptr to first command block
|
|
|
|
set_io reg_scb_ptr
|
|
lea eax, [rxfd]
|
|
GetRealAddr
|
|
out dx, eax
|
|
|
|
set_io reg_scb_cmd
|
|
mov ax, INT_MASK + RX_START
|
|
out dx, ax
|
|
call cmd_wait
|
|
|
|
;-------------------
|
|
; start the receiver
|
|
|
|
mov [rxfd.status], 0
|
|
mov [rxfd.command], 0xc000
|
|
|
|
set_io reg_scb_ptr
|
|
lea eax, [rxfd]
|
|
GetRealAddr
|
|
out dx, eax
|
|
|
|
set_io reg_scb_cmd
|
|
mov ax, INT_MASK + RX_START
|
|
out dx, ax
|
|
call cmd_wait
|
|
|
|
;-----------------
|
|
; set CU base to 0
|
|
|
|
set_io reg_scb_ptr
|
|
xor eax, eax
|
|
out dx, eax
|
|
|
|
set_io reg_scb_cmd
|
|
mov ax, INT_MASK + CU_CMD_BASE
|
|
out dx, ax
|
|
call cmd_wait
|
|
|
|
;--------------------
|
|
; Set TX Base address
|
|
|
|
; First, set up confcmd values
|
|
|
|
mov [txfd.command], CmdIASetup
|
|
mov [txfd.status], 0
|
|
lea eax, [confcmd]
|
|
GetRealAddr
|
|
mov [txfd.link], eax
|
|
|
|
mov word [confcmd.command], Cmdsuspend + CmdConfigure
|
|
mov word [confcmd.status], 0
|
|
lea eax, [txfd]
|
|
GetRealAddr
|
|
mov [confcmd.link], eax
|
|
|
|
mov byte [confcmd.data + 1], 0x88 ; fifo of 8 each
|
|
mov byte [confcmd.data + 4], 0
|
|
mov byte [confcmd.data + 5], 0x80
|
|
mov byte [confcmd.data + 15], 0x48
|
|
mov byte [confcmd.data + 19], 0x80
|
|
mov byte [confcmd.data + 21], 0x05
|
|
|
|
|
|
; CU start
|
|
|
|
; lea eax, [txfd]
|
|
; GetRealAddr
|
|
set_io 0
|
|
set_io reg_scb_ptr
|
|
out dx, eax
|
|
|
|
mov ax, INT_MASK + CU_START
|
|
set_io reg_scb_cmd
|
|
out dx, ax
|
|
call cmd_wait
|
|
|
|
; wait for thing to start
|
|
|
|
; drp004:
|
|
;
|
|
; cmp [txfd.status], 0
|
|
; jz drp004
|
|
|
|
; Indicate that we have successfully reset the card
|
|
|
|
|
|
;;; enable interrupts
|
|
|
|
xor eax, eax
|
|
|
|
ret
|
|
|
|
|
|
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; Transmit ;;
|
|
;; ;;
|
|
;; In: buffer pointer in [esp+4] ;;
|
|
;; size of buffer in [esp+8] ;;
|
|
;; pointer to device structure in ebx ;;
|
|
;; ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
transmit:
|
|
|
|
DEBUGF 1,"Transmitting packet, buffer:%x, size:%u\n",[esp+4],[esp+8]
|
|
mov eax, [esp+4]
|
|
DEBUGF 1,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\
|
|
[eax+00]:2,[eax+01]:2,[eax+02]:2,[eax+03]:2,[eax+04]:2,[eax+05]:2,\
|
|
[eax+06]:2,[eax+07]:2,[eax+08]:2,[eax+09]:2,[eax+10]:2,[eax+11]:2,\
|
|
[eax+13]:2,[eax+12]:2
|
|
|
|
cmp dword [esp+8], 1500
|
|
jg .finish ; packet is too long
|
|
cmp dword [esp+8], 60
|
|
jl .finish ; packet is too short
|
|
|
|
set_io 0
|
|
in ax, dx
|
|
and ax, 0xfc00
|
|
out dx, ax
|
|
|
|
mov [txfd.status], 0
|
|
mov [txfd.command], Cmdsuspend + CmdTx + CmdTxFlex
|
|
lea eax, [txfd]
|
|
GetRealAddr
|
|
mov [txfd.link], eax
|
|
mov [txfd.count], 0x02208000
|
|
lea eax, [txfd.tx_buf_addr0]
|
|
GetRealAddr
|
|
mov [txfd.tx_desc_addr], eax
|
|
|
|
mov eax, [esp+4]
|
|
mov [txfd.tx_buf_addr0], eax
|
|
mov eax, [esp+8]
|
|
mov [txfd.tx_buf_size0], eax
|
|
|
|
; Copy the buffer address and size in
|
|
mov [txfd.tx_buf_addr1], 0
|
|
mov [txfd.tx_buf_size1], 0
|
|
|
|
lea eax, [txfd]
|
|
GetRealAddr
|
|
set_io reg_scb_ptr
|
|
out dx, eax
|
|
|
|
mov ax, INT_MASK + CU_START
|
|
set_io reg_scb_cmd
|
|
out dx, ax
|
|
|
|
call cmd_wait
|
|
|
|
in ax, dx
|
|
|
|
.I8t_001:
|
|
cmp [txfd.status], 0
|
|
je .I8t_001
|
|
|
|
in ax, dx
|
|
|
|
.finish:
|
|
ret 8
|
|
|
|
|
|
|
|
;;;;;;;;;;;;;;;;;;;;;;;
|
|
;; ;;
|
|
;; Interrupt handler ;;
|
|
;; ;;
|
|
;;;;;;;;;;;;;;;;;;;;;;;
|
|
|
|
align 4
|
|
int_handler:
|
|
|
|
DEBUGF 1,"IRQ %x ",eax:2 ; no, you cant replace 'eax:2' with 'al', this must be a bug in FDO
|
|
|
|
; find pointer of device wich made IRQ occur
|
|
|
|
mov esi, device_list
|
|
mov ecx, [devices]
|
|
test ecx, ecx
|
|
jz .fail
|
|
.nextdevice:
|
|
mov ebx, dword [esi]
|
|
|
|
set_io 0
|
|
;; set_io REG_ISR
|
|
;; in ax , dx
|
|
;; out dx , ax ; send it back to ACK
|
|
|
|
add esi, 4
|
|
|
|
test ax , ax
|
|
jnz .got_it
|
|
|
|
dec ecx
|
|
jnz .nextdevice
|
|
|
|
ret ; If no device was found, abort (The irq was probably for a device, not registered to this driver)
|
|
|
|
.got_it:
|
|
|
|
|
|
;;; receive
|
|
|
|
cmp [rxfd.status], 0
|
|
je .nodata
|
|
|
|
mov [rxfd.status], 0
|
|
mov [rxfd.command], 0xc000
|
|
|
|
set_io reg_scb_ptr
|
|
lea eax, [rxfd.status]
|
|
GetRealAddr
|
|
out dx, eax
|
|
|
|
set_io reg_scb_cmd
|
|
mov ax, INT_MASK + RX_START
|
|
out dx, ax
|
|
|
|
call cmd_wait
|
|
|
|
movzx ecx, [rxfd.count]
|
|
and ecx, 0x3fff
|
|
|
|
stdcall KernelAlloc, ecx ; Allocate a buffer to put packet into
|
|
push ecx
|
|
push eax
|
|
|
|
lea esi, [device.rx_buffer]
|
|
|
|
.copy:
|
|
shr ecx, 1
|
|
jnc .nb
|
|
movsb
|
|
.nb:
|
|
shr ecx, 1
|
|
jnc .nw
|
|
movsw
|
|
.nw:
|
|
jz .nd
|
|
rep movsd
|
|
.nd:
|
|
|
|
jmp EthReceiver ; Send it to kernel
|
|
|
|
.nodata:
|
|
.fail:
|
|
|
|
ret
|
|
|
|
|
|
|
|
|
|
align 4
|
|
cmd_wait:
|
|
|
|
in al, dx
|
|
test al, al
|
|
jnz cmd_wait
|
|
|
|
ret
|
|
|
|
|
|
|
|
|
|
|
|
|
|
align 4
|
|
ee_read: ; esi = address to read
|
|
|
|
set_io 0
|
|
set_io reg_eeprom
|
|
|
|
;-----------------------------------------------------
|
|
; Prepend start bit + read opcode to the address field
|
|
; and shift it to the very left bits of esi
|
|
|
|
mov ecx, 32
|
|
sub ecx, [device.ee_bus_width]
|
|
shl esi, cl
|
|
or esi, EE_READ shl 28
|
|
|
|
mov ecx, [device.ee_bus_width]
|
|
add ecx, 3
|
|
|
|
;-----------------------
|
|
; Write this to the chip
|
|
|
|
.loop:
|
|
mov eax, EE_CS
|
|
shl esi, 1
|
|
jnc @f
|
|
or eax, EE_DI
|
|
@@:
|
|
out dx , eax
|
|
delay
|
|
|
|
or eax, EE_SK
|
|
out dx , eax
|
|
delay
|
|
|
|
loop .loop
|
|
|
|
;------------------------------
|
|
; Now read the data from eeprom
|
|
|
|
xor esi, esi
|
|
mov ecx, 16
|
|
|
|
.loop2:
|
|
mov eax, EE_CS + EE_SK
|
|
out dx , eax
|
|
delay
|
|
|
|
in eax, dx
|
|
test eax, EE_DO
|
|
jz @f
|
|
inc esi
|
|
@@:
|
|
shl esi, 1
|
|
|
|
mov eax, EE_CS
|
|
out dx , eax
|
|
delay
|
|
|
|
loop .loop2
|
|
|
|
;-----------------------
|
|
; de-activate the eeprom
|
|
|
|
xor eax, eax
|
|
out dx, eax
|
|
|
|
|
|
DEBUGF 1,"data=%x\n", esi
|
|
ret
|
|
|
|
|
|
|
|
align 4
|
|
ee_write: ; esi = address to write to, di = data
|
|
|
|
set_io 0
|
|
set_io reg_eeprom
|
|
|
|
;-----------------------------------------------------
|
|
; Prepend start bit + write opcode to the address field
|
|
; and shift it to the very left bits of esi
|
|
|
|
mov ecx, 32
|
|
sub ecx, [device.ee_bus_width]
|
|
shl esi, cl
|
|
or esi, EE_WRITE shl 28
|
|
|
|
mov ecx, [device.ee_bus_width]
|
|
add ecx, 3
|
|
|
|
;-----------------------
|
|
; Write this to the chip
|
|
|
|
.loop:
|
|
mov eax, EE_CS
|
|
shl esi, 1
|
|
jnc @f
|
|
or eax, EE_DI
|
|
@@:
|
|
out dx , eax
|
|
delay
|
|
|
|
or eax, EE_SK
|
|
out dx , eax
|
|
delay
|
|
|
|
loop .loop
|
|
|
|
;-----------------------------
|
|
; Now write the data to eeprom
|
|
|
|
mov ecx, 16
|
|
|
|
.loop2:
|
|
mov eax, EE_CS
|
|
shl di , 1
|
|
jnc @f
|
|
or eax, EE_DI
|
|
@@:
|
|
out dx , eax
|
|
delay
|
|
|
|
or eax, EE_SK
|
|
out dx , eax
|
|
delay
|
|
|
|
loop .loop2
|
|
|
|
;-----------------------
|
|
; de-activate the eeprom
|
|
|
|
xor eax, eax
|
|
out dx, eax
|
|
|
|
|
|
ret
|
|
|
|
|
|
|
|
align 4
|
|
ee_get_width:
|
|
|
|
set_io 0
|
|
set_io reg_eeprom
|
|
|
|
mov esi, EE_READ shl 28
|
|
xor ecx, ecx
|
|
|
|
.loop:
|
|
mov eax, EE_CS
|
|
out dx , eax
|
|
delay
|
|
|
|
or eax, EE_SK
|
|
out dx , eax
|
|
delay
|
|
|
|
inc ecx
|
|
|
|
in eax, dx
|
|
test eax, EE_DO
|
|
jnz .loop
|
|
|
|
mov [device.ee_bus_width], ecx
|
|
|
|
;------------------------------
|
|
; Now read the data from eeprom
|
|
|
|
mov ecx, 16
|
|
.loop2:
|
|
mov eax, EE_CS + EE_SK
|
|
out dx , eax
|
|
delay
|
|
|
|
mov eax, EE_CS
|
|
out dx , eax
|
|
delay
|
|
loop .loop2
|
|
|
|
;-----------------------
|
|
; de-activate the eeprom
|
|
|
|
xor eax, eax
|
|
out dx, eax
|
|
|
|
ret
|
|
|
|
|
|
|
|
; cx = phy addr
|
|
; dx = phy reg addr
|
|
|
|
; ax = data
|
|
|
|
align 4
|
|
mdio_read:
|
|
|
|
shl ecx, 21 ; PHY addr
|
|
shl edx, 16 ; PHY reg addr
|
|
|
|
mov eax, ecx
|
|
or eax, edx
|
|
or eax, 10b shl 26 ; read opcode
|
|
|
|
set_io 0
|
|
set_io reg_mdi_ctrl
|
|
out dx, eax
|
|
|
|
.wait:
|
|
delay
|
|
in eax, dx
|
|
test eax, 1 shl 28 ; ready bit
|
|
jz .wait
|
|
|
|
ret
|
|
|
|
; ax = data
|
|
; cx = phy addr
|
|
; dx = phy reg addr
|
|
|
|
; ax = data
|
|
|
|
align 4
|
|
mdio_write:
|
|
|
|
and eax, 0xffff
|
|
|
|
shl ecx, 21 ; PHY addr
|
|
shl edx, 16 ; PHY reg addr
|
|
|
|
or eax, ecx
|
|
or eax, edx
|
|
or eax, 01b shl 26 ; write opcode
|
|
|
|
set_io 0
|
|
set_io reg_mdi_ctrl
|
|
out dx, eax
|
|
|
|
.wait:
|
|
delay
|
|
in eax, dx
|
|
test eax, 1 shl 28 ; ready bit
|
|
jz .wait
|
|
|
|
ret
|
|
|
|
|
|
|
|
align 4
|
|
MAC_read_eeprom:
|
|
|
|
;;;;
|
|
|
|
ret
|
|
|
|
|
|
align 4
|
|
MAC_write:
|
|
|
|
;;;;
|
|
|
|
ret
|
|
|
|
|
|
|
|
|
|
; End of code
|
|
|
|
align 4 ; Place all initialised data here
|
|
|
|
devices dd 0 ; number of currently running devices
|
|
version dd (DRIVER_VERSION shl 16) or (API_VERSION and 0xFFFF)
|
|
my_service db 'i8255x',0 ; max 16 chars include zero
|
|
devicename db 'Intel Etherexpress pro/100',0
|
|
|
|
|
|
device_id_list:
|
|
|
|
dw 0x1029
|
|
dw 0x1030
|
|
dw 0x1031
|
|
dw 0x1032
|
|
dw 0x1033
|
|
dw 0x1034
|
|
dw 0x1038
|
|
dw 0x1039
|
|
dw 0x103A
|
|
dw 0x103B
|
|
dw 0x103C
|
|
dw 0x103D
|
|
dw 0x103E
|
|
dw 0x1050
|
|
dw 0x1051
|
|
dw 0x1052
|
|
dw 0x1053
|
|
dw 0x1054
|
|
dw 0x1055
|
|
dw 0x1056
|
|
dw 0x1057
|
|
dw 0x1059
|
|
dw 0x1064
|
|
dw 0x1065
|
|
dw 0x1066
|
|
dw 0x1067
|
|
dw 0x1068
|
|
dw 0x1069
|
|
dw 0x106A
|
|
dw 0x106B
|
|
dw 0x1091
|
|
dw 0x1092
|
|
dw 0x1093
|
|
dw 0x1094
|
|
dw 0x1095
|
|
dw 0x10fe
|
|
dw 0x1209
|
|
dw 0x1229
|
|
dw 0x2449
|
|
dw 0x2459
|
|
dw 0x245D
|
|
dw 0x27DC
|
|
|
|
DEVICE_IDs = ($ - device_id_list) / 2
|
|
|
|
mac_82557_D100_A = 0
|
|
mac_82557_D100_B = 1
|
|
mac_82557_D100_C = 2
|
|
mac_82558_D101_A4 = 4
|
|
mac_82558_D101_B0 = 5
|
|
mac_82559_D101M = 8
|
|
mac_82559_D101S = 9
|
|
mac_82550_D102 = 12
|
|
mac_82550_D102_C = 13
|
|
mac_82551_E = 14
|
|
mac_82551_F = 15
|
|
mac_82551_10 = 16
|
|
mac_unknown = 0xFF
|
|
|
|
phy_100a = 0x000003E0
|
|
phy_100c = 0x035002A8
|
|
phy_82555_tx = 0x015002A8
|
|
phy_nsc_tx = 0x5C002000
|
|
phy_82562_et = 0x033002A8
|
|
phy_82562_em = 0x032002A8
|
|
phy_82562_ek = 0x031002A8
|
|
phy_82562_eh = 0x017002A8
|
|
phy_82552_v = 0xd061004d
|
|
phy_unknown = 0xFFFFFFFF
|
|
|
|
|
|
include_debug_strings ; All data wich FDO uses will be included here
|
|
|
|
section '.data' data readable writable align 16 ; place all uninitialized data place here
|
|
|
|
device_list rd MAX_DEVICES ; This list contains all pointers to device structures the driver is handling
|
|
|