kolibrios/kernel/branches/Kolibri-A/trunk/docs/apm.txt

519 lines
21 KiB
Plaintext
Raw Normal View History

--------p-155300-----------------------------
INT 15 - Advanced Power Management v1.0+ - INSTALLATION CHECK
AX = 5300h
BX = device ID of system BIOS (0000h)
Return: CF clear if successful
AH = major version (BCD)
AL = minor version (BCD)
BX = 504Dh ("PM")
CX = flags (see #00472)
CF set on error
AH = error code (06h,09h,86h) (see #00473)
BUG: early versions of the Award Modular BIOS with built-in APM support
reportedly do not set BX on return
Bitfields for APM flags:
Bit(s) Description (Table 00472)
0 16-bit protected mode interface supported
1 32-bit protected mode interface supported
2 CPU idle call reduces processor speed
3 BIOS power management disabled
4 BIOS power management disengaged (APM v1.1)
5-7 reserved
(Table 00473)
Values for APM error code:
01h power management functionality disabled
02h interface connection already in effect
03h interface not connected
04h real-mode interface not connected
05h 16-bit protected-mode interface already connected
06h 16-bit protected-mode interface not supported
07h 32-bit protected-mode interface already connected
08h 32-bit protected-mode interface not supported
09h unrecognized device ID
0Ah invalid parameter value in CX
0Bh (APM v1.1) interface not engaged
0Ch (APM v1.2) function not supported
0Dh (APM v1.2) Resume Timer disabled
0Eh-1Fh reserved for other interface and general errors
20h-3Fh reserved for CPU errors
40h-5Fh reserved for device errors
60h can't enter requested state
61h-7Fh reserved for other system errors
80h no power management events pending
81h-85h reserved for other power management event errors
86h APM not present
87h-9Fh reserved for other power management event errors
A0h-FEh reserved
FFh undefined
--------p-155301-----------------------------
INT 15 - Advanced Power Management v1.0+ - CONNECT REAL-MODE INTERFACE
AX = 5301h
BX = device ID of system BIOS (0000h)
Return: CF clear if successful
CF set on error
AH = error code (02h,05h,07h,09h) (see #00473)
Note: on connection, an APM v1.1 or v1.2 BIOS switches to APM v1.0
compatibility mode until it is informed that the user supports a
newer version of APM (see AX=530Eh)
SeeAlso: AX=5302h,AX=5303h,AX=5304h
--------p-155302-----------------------------
INT 15 R - Advanced Power Management v1.0+ - CONNECT 16-BIT PROTMODE INTERFACE
AX = 5302h
BX = device ID of system BIOS (0000h)
Return: CF clear if successful
AX = real-mode segment base address of protected-mode 16-bit code
segment
BX = offset of entry point
CX = real-mode segment base address of protected-mode 16-bit data
segment
---APM v1.1---
SI = APM BIOS code segment length
DI = APM BIOS data segment length
CF set on error
AH = error code (02h,05h,06h,07h,09h) (see #00473)
Notes: the caller must initialize two consecutive descriptors with the
returned segment base addresses; these descriptors must be valid
whenever the protected-mode interface is called, and will have
their limits arbitrarily set to 64K.
the protected mode interface is invoked by making a far call with the
same register values as for INT 15; it must be invoked while CPL=0,
the code segment descriptor must have a DPL of 0, the stack must be
in a 16-bit segment and have enough room for BIOS use and possible
interrupts, and the current I/O permission bit map must allow access
to the I/O ports used for power management.
functions 00h-03h are not available from protected mode
on connection, an APM v1.1 or v1.2 BIOS switches to APM v1.0
compatibility mode until it is informed that the user supports a
newer version of APM (see AX=530Eh)
SeeAlso: AX=5301h,AX=5303h,AX=5304h
--------p-155303-----------------------------
INT 15 - Advanced Power Management v1.0+ - CONNECT 32-BIT PROTMODE INTERFACE
AX = 5303h
BX = device ID of system BIOS (0000h)
Return: CF clear if successful
AX = real-mode segment base address of protected-mode 32-bit code
segment
EBX = offset of entry point
CX = real-mode segment base address of protected-mode 16-bit code
segment
DX = real-mode segment base address of protected-mode 16-bit data
segment
---APM v1.1---
SI = APM BIOS code segment length
DI = APM BIOS data segment length
CF set on error
AH = error code (02h,05h,07h,08h,09h) (see #00473)
Notes: the caller must initialize three consecutive descriptors with the
returned segment base addresses for 32-bit code, 16-bit code, and
16-bit data, respectively; these descriptors must be valid whenever
the protected-mode interface is called, and will have their limits
arbitrarily set to 64K.
the protected mode interface is invoked by making a far call to the
32-bit code segment with the same register values as for INT 15; it
must be invoked while CPL=0, the code segment descriptor must have a
DPL of 0, the stack must be in a 32-bit segment and have enough room
for BIOS use and possible interrupts, and the current I/O permission
bit map must allow access to the I/O ports used for power management.
functions 00h-03h are not available from protected mode
on connection, an APM v1.1 or v1.2 BIOS switches to APM v1.0
compatibility mode until it is informed that the user supports a
newer version of APM (see AX=530Eh)
SeeAlso: AX=5301h,AX=5302h,AX=5304h
--------p-155304-----------------------------
INT 15 - Advanced Power Management v1.0+ - DISCONNECT INTERFACE
AX = 5304h
BX = device ID of system BIOS (0000h)
Return: CF clear if successful
CF set on error
AH = error code (03h,09h) (see #00473)
SeeAlso: AX=5301h,AX=5302h,AX=5303h
--------p-155305-----------------------------
INT 15 - Advanced Power Management v1.0+ - CPU IDLE
AX = 5305h
Return: CF clear if successful (after system leaves idle state)
CF set on error
AH = error code (03h,0Bh) (see #00473)
Notes: call when the system is idle and should be suspended until the next
system event or interrupt
should not be called from within a hardware interrupt handler to avoid
reentrance problems
if an interrupt causes the system to resume normal processing, the
interrupt may or may not have been handled when the BIOS returns
from this call; thus, the caller should allow interrupts on return
interrupt handlers may not retain control if the BIOS allows
interrupts while in idle mode even if they are able to determine
that they were called from idle mode
the caller should issue this call continuously in a loop until it needs
to perform some processing of its own
SeeAlso: AX=1000h,AX=5306h,INT 2F/AX=1680h
--------p-155306-----------------------------
INT 15 - Advanced Power Management v1.0+ - CPU BUSY
AX = 5306h
Return: CF clear if successful
CF set on error
AH = error code (03h,0Bh) (see #00473)
Notes: called to ensure that the system runs at full speed even on systems
where the BIOS is unable to recognize increased activity (especially
if interrupts are hooked by other programs and not chained to the
BIOS)
this call may be made even when the system is already running at full
speed, but it will create unnecessary overhead
should not be called from within a hardware interrupt handler to avoid
reentrance problems
SeeAlso: AX=5305h
--------p-155307-----------------------------
INT 15 - Advanced Power Management v1.0+ - SET POWER STATE
AX = 5307h
BX = device ID (see #00474)
CX = system state ID (see #00475)
Return: CF clear if successful
CF set on error
AH = error code (01h,03h,09h,0Ah,0Bh,60h) (see #00473)
Note: should not be called from within a hardware interrupt handler to avoid
reentrance problems
SeeAlso: AX=530Ch
(Table 00474)
Values for APM device IDs:
0000h system BIOS
0001h all devices for which the system BIOS manages power
01xxh display (01FFh for all attached display devices)
02xxh secondary storage (02FFh for all attached secondary storage devices)
03xxh parallel ports (03FFh for all attached parallel ports)
04xxh serial ports (04FFh for all attached serial ports)
---APM v1.1+ ---
05xxh network adapters (05FFh for all attached network adapters)
06xxh PCMCIA sockets (06FFh for all)
0700h-7FFFh reserved
80xxh system battery devices (APM v1.2)
8100h-DFFFh reserved
Exxxh OEM-defined power device IDs
F000h-FFFFh reserved
(Table 00475)
Values for system state ID:
0000h ready (not supported for device ID 0001h)
0001h stand-by
0002h suspend
0003h off (not supported for device ID 0001h in APM v1.0)
---APM v1.1---
0004h last request processing notification (only for device ID 0001h)
0005h last request rejected (only for device ID 0001h)
0006h-001Fh reserved system states
0020h-003Fh OEM-defined system states
0040h-007Fh OEM-defined device states
0080h-FFFFh reserved device states
--------p-155307CX0001-----------------------
INT 15 - Advanced Power Management v1.0+ - SYSTEM STAND-BY
AX = 5307h
CX = 0001h
BX = 0001h (device ID for all power-managed devices)
Return: CF clear
Notes: puts the entire system into stand-by mode; normally called in response
to a System Stand-by Request notification after any necessary
processing, but may also be invoked at the caller's discretion
should not be called from within a hardware interrupt handler to avoid
reentrance problems
the stand-by state is typically exited on an interrupt
SeeAlso: AX=4280h,AX=5307h/CX=0002h"SUSPEND",AX=5307h/CX=0003h,AX=530Bh
--------p-155307CX0002-----------------------
INT 15 - Advanced Power Management v1.0+ - SUSPEND SYSTEM
AX = 5307h
CX = 0002h
BX = 0001h (device ID for all power-managed devices)
Return: after system is resumed
CF clear
Notes: puts the entire system into a low-power suspended state; normally
called in response to a Suspend System Request notification after
any necessary processing, but may also be invoked at the caller's
discretion
should not be called from within a hardware interrupt handler to avoid
reentrance problems
the caller may need to update its date and time values because the
system could have been suspended for a long period of time
SeeAlso: AX=5307h/CX=0001h"STAND-BY",AX=530Bh
--------p-155307CX0003-----------------------
INT 15 - Advanced Power Management v1.2 - TURN OFF SYSTEM
AX = 5307h
CX = 0003h
BX = 0001h (device ID for all power-managed devices)
Return: after system is resumed
CF clear
Notes: if supported by the system's power supply, turns off the system power
SeeAlso: AX=5307h/CX=0001h"STAND-BY",AX=530Bh
--------p-155308-----------------------------
INT 15 - Advanced Power Management v1.0+ - ENABLE/DISABLE POWER MANAGEMENT
AX = 5308h
BX = device ID for all devices power-managed by APM
0001h (APM v1.1+)
FFFFh (APM v1.0)
CX = new state
0000h disabled
0001h enabled
Return: CF clear if successful
CF set on error
AH = error code (01h,03h,09h,0Ah,0Bh) (see #00473)
Notes: when power management is disabled, the system BIOS will not
automatically power down devices, enter stand-by or suspended mode,
or perform any power-saving actions in response to AX=5305h calls
should not be called from within a hardware interrupt handler to avoid
reentrance problems
the APM BIOS should never be both disabled and disengaged at the same
time
SeeAlso: AX=5309h,AX=530Dh,AX=530Fh
--------p-155309-----------------------------
INT 15 - Advanced Power Management v1.0+ - RESTORE POWER-ON DEFAULTS
AX = 5309h
BX = device ID for all devices power-managed by APM
0001h (APM v1.1)
FFFFh (APM v1.0)
Return: CF clear if successful
CF set on error
AH = error code (03h,09h,0Bh) (see #00473)
Note: should not be called from within a hardware interrupt handler to avoid
reentrance problems
SeeAlso: AX=5308h
--------p-15530A-----------------------------
INT 15 - Advanced Power Management v1.0+ - GET POWER STATUS
AX = 530Ah
BX = device ID
0001h all devices power-managed by APM
80xxh specific battery unit number XXh (01h-FFh) (APM v1.2)
Return: CF clear if successful
BH = AC line status
00h off-line
01h on-line
02h on backup power (APM v1.1)
FFh unknown
other reserved
BL = battery status (see #00476)
CH = battery flag (APM v1.1+) (see #00477)
CL = remaining battery life, percentage
00h-64h (0-100) percentage of full charge
FFh unknown
DX = remaining battery life, time (APM v1.1) (see #00478)
---if specific battery unit specified---
SI = number of battery units currently installed
CF set on error
AH = error code (09h,0Ah) (see #00473)
Notes: should not be called from within a hardware interrupt handler to avoid
reentrance problems
supported in real mode (INT 15) and both 16-bit and 32-bit protected
mode
(Table 00476)
Values for APM v1.0+ battery status:
00h high
01h low
02h critical
03h charging
FFh unknown
other reserved
SeeAlso: #00477,#00478
Bitfields for APM v1.1+ battery flag:
Bit(s) Description (Table 00477)
0 high
1 low
2 critical
3 charging
4 selected battery not present (APM v1.2)
5-6 reserved (0)
7 no system battery
Note: all bits set (FFh) if unknown
SeeAlso: #00476,#00478
Bitfields for APM v1.1+ remaining battery life:
Bit(s) Description (Table 00478)
15 time units: 0=seconds, 1=minutes
14-0 battery life in minutes or seconds
Note: all bits set (FFFFh) if unknown
SeeAlso: #00476,#00477
--------p-15530B-----------------------------
INT 15 - Advanced Power Management v1.0+ - GET POWER MANAGEMENT EVENT
AX = 530Bh
Return: CF clear if successful
BX = event code (see #00479)
CX = event information (APM v1.2) if BX=0003h or BX=0004h
bit 0: PCMCIA socket was powered down in suspend state
CF set on error
AH = error code (03h,0Bh,80h) (see #00473)
Notes: although power management events are often asynchronous, notification
will not be made until polled via this call to permit software to
only receive event notification when it is prepared to process
power management events; since these events are not very time-
critical, it should be sufficient to poll once or twice per second
the critical resume notification is made after the system resumes
from an emergency suspension; normally, the system BIOS only notifies
its partner that it wishes to suspend and relies on the partner to
actually request the suspension, but no notification is made on an
emergency suspension
should not be called from within a hardware interrupt handler to avoid
reentrance problems
SeeAlso: AX=5307h,AX=5307h/CX=0001h"STAND-BY",AX=5307h/CX=0002h"SUSPEND"
(Table 00479)
Values for APM event code:
0001h system stand-by request
0002h system suspend request
0003h normal resume system notification
0004h critical resume system notification
0005h battery low notification
---APM v1.1---
0006h power status change notification
0007h update time notification
0008h critical system suspend notification
0009h user system standby request notification
000Ah user system suspend request notification
000Bh system standby resume notification
---APM v1.2---
000Ch capabilities change notification (see AX=5310h)
------
000Dh-00FFh reserved system events
01xxh reserved device events
02xxh OEM-defined APM events
0300h-FFFFh reserved
--------p-15530C-----------------------------
INT 15 - Advanced Power Management v1.1+ - GET POWER STATE
AX = 530Ch
BX = device ID (see #00474)
Return: CF clear if successful
CX = system state ID (see #00475)
CF set on error
AH = error code (01h,09h) (see #00473)
SeeAlso: AX=5307h
--------p-15530D-----------------------------
INT 15 - Advanced Power Management v1.1+ - EN/DISABLE DEVICE POWER MANAGEMENT
AX = 530Dh
BX = device ID (see #00474)
CX = function
0000h disable power management
0001h enable power management
Return: CF clear if successful
CF set on error
AH = error code (01h,03h,09h,0Ah,0Bh) (see #00473)
Desc: specify whether automatic power management should be active for a
given device
SeeAlso: AX=5308h,AX=530Fh
--------p-15530E-----------------------------
INT 15 - Advanced Power Management v1.1+ - DRIVER VERSION
AX = 530Eh
BX = device ID of system BIOS (0000h)
CH = APM driver major version (BCD)
CL = APM driver minor version (BCD) (02h for APM v1.2)
Return: CF clear if successful
AH = APM connection major version (BCD)
AL = APM connection minor version (BCD)
CF set on error
AH = error code (03h,09h,0Bh) (see #00473)
SeeAlso: AX=5300h,AX=5303h
--------p-15530F-----------------------------
INT 15 - Advanced Power Management v1.1+ - ENGAGE/DISENGAGE POWER MANAGEMENT
AX = 530Fh
BX = device ID (see #00474)
CX = function
0000h disengage power management
0001h engage power management
Return: CF clear if successful
CF set on error
AH = error code (01h,09h) (see #00473)
Notes: unlike AX=5308h, this call does not affect the functioning of the APM
BIOS
when cooperative power management is disengaged, the APM BIOS performs
automatic power management of the system or device
SeeAlso: AX=5308h,AX=530Dh
--------p-155310-----------------------------
INT 15 - Advanced Power Management v1.2 - GET CAPABILITIES
AX = 5310h
BX = device ID (see #00474)
0000h (APM BIOS)
other reserved
Return: CF clear if successful
BL = number of battery units supported (00h if no system batteries)
CX = capabilities flags (see #00480)
CF set on error
AH = error code (01h,09h,86h) (see #00473)
Notes: this function is supported via the INT 15, 16-bit protected mode, and
32-bit protected mode interfaces; it does not require that a
connection be established prior to use
this function will return the capabilities currently in effect, not
any new settings which have been made but do not take effect until
a system restart
SeeAlso: AX=5300h,AX=530Fh,AX=5311h,AX=5312h,AX=5313h
Bitfields for APM v1.2 capabilities flags:
Bit(s) Description (Table 00480)
15-8 reserved
7 PCMCIA Ring Indicator will wake up system from suspend mode
6 PCMCIA Ring Indicator will wake up system from standby mode
5 Resume on Ring Indicator will wake up system from suspend mode
4 Resume on Ring Indicator will wake up system from standby mode
3 resume timer will wake up system from suspend mode
2 resume timer will wake up system from standby mode
1 can enter global suspend state
0 can enter global standby state
--------p-155311-----------------------------
INT 15 - Advanced Power Management v1.2 - GET/SET/DISABLE RESUME TIMER
AX = 5311h
BX = device ID (see #00474)
0000h (APM BIOS)
other reserved
CL = function
00h disable Resume Timer
01h get Resume Timer
02h set Resume Timer
CH = resume time, seconds (BCD)
DL = resume time, minutes (BCD)
DH = resume time, hours (BCD)
SI = resume date (BCD), high byte = month, low byte = day
DI = resume date, year (BCD)
Return: CF clear if successful
---if getting timer---
CH = resume time, seconds (BCD)
DL = resume time, minutes (BCD)
DH = resume time, hours (BCD)
SI = resume date (BCD), high byte = month, low byte = day
DI = resume date, year (BCD)
CF set on error
AH = error code (03h,09h,0Ah,0Bh,0Ch,0Dh,86h) (see #00473)
Notes: this function is supported via the INT 15, 16-bit protected mode, and
32-bit protected mode interfaces
SeeAlso: AX=5300h,AX=5310h,AX=5312h,AX=5313h
--------p-155312-----------------------------
INT 15 - Advanced Power Management v1.2 - ENABLE/DISABLE RESUME ON RING
AX = 5312h
BX = device ID (see #00474)
0000h (APM BIOS)
other reserved
CL = function
00h disable Resume on Ring Indicator
01h enable Resume on Ring Indicator
02h get Resume on Ring Indicator status
Return: CF clear if successful
CX = resume status (0000h disabled, 0001h enabled)
CF set on error
AH = error code (03h,09h,0Ah,0Bh,0Ch,86h) (see #00473)
Notes: this function is supported via the INT 15, 16-bit protected mode, and
32-bit protected mode interfaces
SeeAlso: AX=5300h,AX=5310h,AX=5311h,AX=5313h
--------p-155313-----------------------------
INT 15 - Advanced Power Management v1.2 - ENABLE/DISABLE TIMER-BASED REQUESTS
AX = 5313h
BX = device ID (see #00474)
0000h (APM BIOS)
other reserved
CL = function
00h disable timer-based requests
01h enable timer-based requests
02h get timer-based requests status
Return: CF clear if successful
CX = timer-based requests status (0000h disabled, 0001h enabled)
CF set on error
AH = error code (03h,09h,0Ah,0Bh,86h) (see #00473)
Notes: this function is supported via the INT 15, 16-bit protected mode, and
32-bit protected mode interfaces
some BIOSes set AH on return even when successful
SeeAlso: AX=5300h,AX=5310h,AX=5311h,AX=5312h