kolibrios/contrib/sdk/sources/ffmpeg/doc/ffmpeg-devices.pod

1475 lines
30 KiB
Plaintext
Raw Normal View History

=head1 NAME
ffmpeg-devices - FFmpeg devices
=head1 DESCRIPTION
This document describes the input and output devices provided by the
libavdevice library.
=head1 DEVICE OPTIONS
The libavdevice library provides the same interface as
libavformat. Namely, an input device is considered like a demuxer, and
an output device like a muxer, and the interface and generic device
options are the same provided by libavformat (see the ffmpeg-formats
manual).
In addition each input or output device may support so-called private
options, which are specific for that component.
Options may be set by specifying -I<option> I<value> in the
FFmpeg tools, or by setting the value explicitly in the device
C<AVFormatContext> options or using the F<libavutil/opt.h> API
for programmatic use.
=head1 INPUT DEVICES
Input devices are configured elements in FFmpeg which allow to access
the data coming from a multimedia device attached to your system.
When you configure your FFmpeg build, all the supported input devices
are enabled by default. You can list all available ones using the
configure option "--list-indevs".
You can disable all the input devices using the configure option
"--disable-indevs", and selectively enable an input device using the
option "--enable-indev=I<INDEV>", or you can disable a particular
input device using the option "--disable-indev=I<INDEV>".
The option "-formats" of the ff* tools will display the list of
supported input devices (amongst the demuxers).
A description of the currently available input devices follows.
=head2 alsa
ALSA (Advanced Linux Sound Architecture) input device.
To enable this input device during configuration you need libasound
installed on your system.
This device allows capturing from an ALSA device. The name of the
device to capture has to be an ALSA card identifier.
An ALSA identifier has the syntax:
hw:<CARD>[,<DEV>[,<SUBDEV>]]
where the I<DEV> and I<SUBDEV> components are optional.
The three arguments (in order: I<CARD>,I<DEV>,I<SUBDEV>)
specify card number or identifier, device number and subdevice number
(-1 means any).
To see the list of cards currently recognized by your system check the
files F</proc/asound/cards> and F</proc/asound/devices>.
For example to capture with B<ffmpeg> from an ALSA device with
card id 0, you may run the command:
ffmpeg -f alsa -i hw:0 alsaout.wav
For more information see:
E<lt>B<http://www.alsa-project.org/alsa-doc/alsa-lib/pcm.html>E<gt>
=head2 bktr
BSD video input device.
=head2 dshow
Windows DirectShow input device.
DirectShow support is enabled when FFmpeg is built with the mingw-w64 project.
Currently only audio and video devices are supported.
Multiple devices may be opened as separate inputs, but they may also be
opened on the same input, which should improve synchronism between them.
The input name should be in the format:
<TYPE>=<NAME>[:<TYPE>=<NAME>]
where I<TYPE> can be either I<audio> or I<video>,
and I<NAME> is the device's name.
=head3 Options
If no options are specified, the device's defaults are used.
If the device does not support the requested options, it will
fail to open.
=over 4
=item B<video_size>
Set the video size in the captured video.
=item B<framerate>
Set the frame rate in the captured video.
=item B<sample_rate>
Set the sample rate (in Hz) of the captured audio.
=item B<sample_size>
Set the sample size (in bits) of the captured audio.
=item B<channels>
Set the number of channels in the captured audio.
=item B<list_devices>
If set to B<true>, print a list of devices and exit.
=item B<list_options>
If set to B<true>, print a list of selected device's options
and exit.
=item B<video_device_number>
Set video device number for devices with same name (starts at 0,
defaults to 0).
=item B<audio_device_number>
Set audio device number for devices with same name (starts at 0,
defaults to 0).
=item B<pixel_format>
Select pixel format to be used by DirectShow. This may only be set when
the video codec is not set or set to rawvideo.
=item B<audio_buffer_size>
Set audio device buffer size in milliseconds (which can directly
impact latency, depending on the device).
Defaults to using the audio device's
default buffer size (typically some multiple of 500ms).
Setting this value too low can degrade performance.
See also
E<lt>B<http://msdn.microsoft.com/en-us/library/windows/desktop/dd377582(v=vs.85).aspx>E<gt>
=back
=head3 Examples
=over 4
=item *
Print the list of DirectShow supported devices and exit:
$ ffmpeg -list_devices true -f dshow -i dummy
=item *
Open video device I<Camera>:
$ ffmpeg -f dshow -i video="Camera"
=item *
Open second video device with name I<Camera>:
$ ffmpeg -f dshow -video_device_number 1 -i video="Camera"
=item *
Open video device I<Camera> and audio device I<Microphone>:
$ ffmpeg -f dshow -i video="Camera":audio="Microphone"
=item *
Print the list of supported options in selected device and exit:
$ ffmpeg -list_options true -f dshow -i video="Camera"
=back
=head2 dv1394
Linux DV 1394 input device.
=head2 fbdev
Linux framebuffer input device.
The Linux framebuffer is a graphic hardware-independent abstraction
layer to show graphics on a computer monitor, typically on the
console. It is accessed through a file device node, usually
F</dev/fb0>.
For more detailed information read the file
Documentation/fb/framebuffer.txt included in the Linux source tree.
To record from the framebuffer device F</dev/fb0> with
B<ffmpeg>:
ffmpeg -f fbdev -r 10 -i /dev/fb0 out.avi
You can take a single screenshot image with the command:
ffmpeg -f fbdev -frames:v 1 -r 1 -i /dev/fb0 screenshot.jpeg
See also E<lt>B<http://linux-fbdev.sourceforge.net/>E<gt>, and fbset(1).
=head2 iec61883
FireWire DV/HDV input device using libiec61883.
To enable this input device, you need libiec61883, libraw1394 and
libavc1394 installed on your system. Use the configure option
C<--enable-libiec61883> to compile with the device enabled.
The iec61883 capture device supports capturing from a video device
connected via IEEE1394 (FireWire), using libiec61883 and the new Linux
FireWire stack (juju). This is the default DV/HDV input method in Linux
Kernel 2.6.37 and later, since the old FireWire stack was removed.
Specify the FireWire port to be used as input file, or "auto"
to choose the first port connected.
=head3 Options
=over 4
=item B<dvtype>
Override autodetection of DV/HDV. This should only be used if auto
detection does not work, or if usage of a different device type
should be prohibited. Treating a DV device as HDV (or vice versa) will
not work and result in undefined behavior.
The values B<auto>, B<dv> and B<hdv> are supported.
=item B<dvbuffer>
Set maxiumum size of buffer for incoming data, in frames. For DV, this
is an exact value. For HDV, it is not frame exact, since HDV does
not have a fixed frame size.
=item B<dvguid>
Select the capture device by specifying it's GUID. Capturing will only
be performed from the specified device and fails if no device with the
given GUID is found. This is useful to select the input if multiple
devices are connected at the same time.
Look at /sys/bus/firewire/devices to find out the GUIDs.
=back
=head3 Examples
=over 4
=item *
Grab and show the input of a FireWire DV/HDV device.
ffplay -f iec61883 -i auto
=item *
Grab and record the input of a FireWire DV/HDV device,
using a packet buffer of 100000 packets if the source is HDV.
ffmpeg -f iec61883 -i auto -hdvbuffer 100000 out.mpg
=back
=head2 jack
JACK input device.
To enable this input device during configuration you need libjack
installed on your system.
A JACK input device creates one or more JACK writable clients, one for
each audio channel, with name I<client_name>:input_I<N>, where
I<client_name> is the name provided by the application, and I<N>
is a number which identifies the channel.
Each writable client will send the acquired data to the FFmpeg input
device.
Once you have created one or more JACK readable clients, you need to
connect them to one or more JACK writable clients.
To connect or disconnect JACK clients you can use the B<jack_connect>
and B<jack_disconnect> programs, or do it through a graphical interface,
for example with B<qjackctl>.
To list the JACK clients and their properties you can invoke the command
B<jack_lsp>.
Follows an example which shows how to capture a JACK readable client
with B<ffmpeg>.
# Create a JACK writable client with name "ffmpeg".
$ ffmpeg -f jack -i ffmpeg -y out.wav
# Start the sample jack_metro readable client.
$ jack_metro -b 120 -d 0.2 -f 4000
# List the current JACK clients.
$ jack_lsp -c
system:capture_1
system:capture_2
system:playback_1
system:playback_2
ffmpeg:input_1
metro:120_bpm
# Connect metro to the ffmpeg writable client.
$ jack_connect metro:120_bpm ffmpeg:input_1
For more information read:
E<lt>B<http://jackaudio.org/>E<gt>
=head2 lavfi
Libavfilter input virtual device.
This input device reads data from the open output pads of a libavfilter
filtergraph.
For each filtergraph open output, the input device will create a
corresponding stream which is mapped to the generated output. Currently
only video data is supported. The filtergraph is specified through the
option B<graph>.
=head3 Options
=over 4
=item B<graph>
Specify the filtergraph to use as input. Each video open output must be
labelled by a unique string of the form "outI<N>", where I<N> is a
number starting from 0 corresponding to the mapped input stream
generated by the device.
The first unlabelled output is automatically assigned to the "out0"
label, but all the others need to be specified explicitly.
If not specified defaults to the filename specified for the input
device.
=item B<graph_file>
Set the filename of the filtergraph to be read and sent to the other
filters. Syntax of the filtergraph is the same as the one specified by
the option I<graph>.
=back
=head3 Examples
=over 4
=item *
Create a color video stream and play it back with B<ffplay>:
ffplay -f lavfi -graph "color=c=pink [out0]" dummy
=item *
As the previous example, but use filename for specifying the graph
description, and omit the "out0" label:
ffplay -f lavfi color=c=pink
=item *
Create three different video test filtered sources and play them:
ffplay -f lavfi -graph "testsrc [out0]; testsrc,hflip [out1]; testsrc,negate [out2]" test3
=item *
Read an audio stream from a file using the amovie source and play it
back with B<ffplay>:
ffplay -f lavfi "amovie=test.wav"
=item *
Read an audio stream and a video stream and play it back with
B<ffplay>:
ffplay -f lavfi "movie=test.avi[out0];amovie=test.wav[out1]"
=back
=head2 libdc1394
IIDC1394 input device, based on libdc1394 and libraw1394.
=head2 openal
The OpenAL input device provides audio capture on all systems with a
working OpenAL 1.1 implementation.
To enable this input device during configuration, you need OpenAL
headers and libraries installed on your system, and need to configure
FFmpeg with C<--enable-openal>.
OpenAL headers and libraries should be provided as part of your OpenAL
implementation, or as an additional download (an SDK). Depending on your
installation you may need to specify additional flags via the
C<--extra-cflags> and C<--extra-ldflags> for allowing the build
system to locate the OpenAL headers and libraries.
An incomplete list of OpenAL implementations follows:
=over 4
=item B<Creative>
The official Windows implementation, providing hardware acceleration
with supported devices and software fallback.
See E<lt>B<http://openal.org/>E<gt>.
=item B<OpenAL Soft>
Portable, open source (LGPL) software implementation. Includes
backends for the most common sound APIs on the Windows, Linux,
Solaris, and BSD operating systems.
See E<lt>B<http://kcat.strangesoft.net/openal.html>E<gt>.
=item B<Apple>
OpenAL is part of Core Audio, the official Mac OS X Audio interface.
See E<lt>B<http://developer.apple.com/technologies/mac/audio-and-video.html>E<gt>
=back
This device allows to capture from an audio input device handled
through OpenAL.
You need to specify the name of the device to capture in the provided
filename. If the empty string is provided, the device will
automatically select the default device. You can get the list of the
supported devices by using the option I<list_devices>.
=head3 Options
=over 4
=item B<channels>
Set the number of channels in the captured audio. Only the values
B<1> (monaural) and B<2> (stereo) are currently supported.
Defaults to B<2>.
=item B<sample_size>
Set the sample size (in bits) of the captured audio. Only the values
B<8> and B<16> are currently supported. Defaults to
B<16>.
=item B<sample_rate>
Set the sample rate (in Hz) of the captured audio.
Defaults to B<44.1k>.
=item B<list_devices>
If set to B<true>, print a list of devices and exit.
Defaults to B<false>.
=back
=head3 Examples
Print the list of OpenAL supported devices and exit:
$ ffmpeg -list_devices true -f openal -i dummy out.ogg
Capture from the OpenAL device F<DR-BT101 via PulseAudio>:
$ ffmpeg -f openal -i 'DR-BT101 via PulseAudio' out.ogg
Capture from the default device (note the empty string '' as filename):
$ ffmpeg -f openal -i '' out.ogg
Capture from two devices simultaneously, writing to two different files,
within the same B<ffmpeg> command:
$ ffmpeg -f openal -i 'DR-BT101 via PulseAudio' out1.ogg -f openal -i 'ALSA Default' out2.ogg
Note: not all OpenAL implementations support multiple simultaneous capture -
try the latest OpenAL Soft if the above does not work.
=head2 oss
Open Sound System input device.
The filename to provide to the input device is the device node
representing the OSS input device, and is usually set to
F</dev/dsp>.
For example to grab from F</dev/dsp> using B<ffmpeg> use the
command:
ffmpeg -f oss -i /dev/dsp /tmp/oss.wav
For more information about OSS see:
E<lt>B<http://manuals.opensound.com/usersguide/dsp.html>E<gt>
=head2 pulse
PulseAudio input device.
To enable this output device you need to configure FFmpeg with C<--enable-libpulse>.
The filename to provide to the input device is a source device or the
string "default"
To list the PulseAudio source devices and their properties you can invoke
the command B<pactl list sources>.
More information about PulseAudio can be found on E<lt>B<http://www.pulseaudio.org>E<gt>.
=head3 Options
=over 4
=item B<server>
Connect to a specific PulseAudio server, specified by an IP address.
Default server is used when not provided.
=item B<name>
Specify the application name PulseAudio will use when showing active clients,
by default it is the C<LIBAVFORMAT_IDENT> string.
=item B<stream_name>
Specify the stream name PulseAudio will use when showing active streams,
by default it is "record".
=item B<sample_rate>
Specify the samplerate in Hz, by default 48kHz is used.
=item B<channels>
Specify the channels in use, by default 2 (stereo) is set.
=item B<frame_size>
Specify the number of bytes per frame, by default it is set to 1024.
=item B<fragment_size>
Specify the minimal buffering fragment in PulseAudio, it will affect the
audio latency. By default it is unset.
=back
=head3 Examples
Record a stream from default device:
ffmpeg -f pulse -i default /tmp/pulse.wav
=head2 sndio
sndio input device.
To enable this input device during configuration you need libsndio
installed on your system.
The filename to provide to the input device is the device node
representing the sndio input device, and is usually set to
F</dev/audio0>.
For example to grab from F</dev/audio0> using B<ffmpeg> use the
command:
ffmpeg -f sndio -i /dev/audio0 /tmp/oss.wav
=head2 video4linux2, v4l2
Video4Linux2 input video device.
"v4l2" can be used as alias for "video4linux2".
If FFmpeg is built with v4l-utils support (by using the
C<--enable-libv4l2> configure option), it is possible to use it with the
C<-use_libv4l2> input device option.
The name of the device to grab is a file device node, usually Linux
systems tend to automatically create such nodes when the device
(e.g. an USB webcam) is plugged into the system, and has a name of the
kind F</dev/videoI<N>>, where I<N> is a number associated to
the device.
Video4Linux2 devices usually support a limited set of
I<width>xI<height> sizes and frame rates. You can check which are
supported using B<-list_formats all> for Video4Linux2 devices.
Some devices, like TV cards, support one or more standards. It is possible
to list all the supported standards using B<-list_standards all>.
The time base for the timestamps is 1 microsecond. Depending on the kernel
version and configuration, the timestamps may be derived from the real time
clock (origin at the Unix Epoch) or the monotonic clock (origin usually at
boot time, unaffected by NTP or manual changes to the clock). The
B<-timestamps abs> or B<-ts abs> option can be used to force
conversion into the real time clock.
Some usage examples of the video4linux2 device with B<ffmpeg>
and B<ffplay>:
=over 4
=item *
Grab and show the input of a video4linux2 device:
ffplay -f video4linux2 -framerate 30 -video_size hd720 /dev/video0
=item *
Grab and record the input of a video4linux2 device, leave the
frame rate and size as previously set:
ffmpeg -f video4linux2 -input_format mjpeg -i /dev/video0 out.mpeg
=back
For more information about Video4Linux, check E<lt>B<http://linuxtv.org/>E<gt>.
=head3 Options
=over 4
=item B<standard>
Set the standard. Must be the name of a supported standard. To get a
list of the supported standards, use the B<list_standards>
option.
=item B<channel>
Set the input channel number. Default to -1, which means using the
previously selected channel.
=item B<video_size>
Set the video frame size. The argument must be a string in the form
I<WIDTH>xI<HEIGHT> or a valid size abbreviation.
=item B<pixel_format>
Select the pixel format (only valid for raw video input).
=item B<input_format>
Set the preferred pixel format (for raw video) or a codec name.
This option allows to select the input format, when several are
available.
=item B<framerate>
Set the preferred video frame rate.
=item B<list_formats>
List available formats (supported pixel formats, codecs, and frame
sizes) and exit.
Available values are:
=over 4
=item B<all>
Show all available (compressed and non-compressed) formats.
=item B<raw>
Show only raw video (non-compressed) formats.
=item B<compressed>
Show only compressed formats.
=back
=item B<list_standards>
List supported standards and exit.
Available values are:
=over 4
=item B<all>
Show all supported standards.
=back
=item B<timestamps, ts>
Set type of timestamps for grabbed frames.
Available values are:
=over 4
=item B<default>
Use timestamps from the kernel.
=item B<abs>
Use absolute timestamps (wall clock).
=item B<mono2abs>
Force conversion from monotonic to absolute timestamps.
=back
Default value is C<default>.
=back
=head2 vfwcap
VfW (Video for Windows) capture input device.
The filename passed as input is the capture driver number, ranging from
0 to 9. You may use "list" as filename to print a list of drivers. Any
other filename will be interpreted as device number 0.
=head2 x11grab
X11 video input device.
This device allows to capture a region of an X11 display.
The filename passed as input has the syntax:
[<hostname>]:<display_number>.<screen_number>[+<x_offset>,<y_offset>]
I<hostname>:I<display_number>.I<screen_number> specifies the
X11 display name of the screen to grab from. I<hostname> can be
omitted, and defaults to "localhost". The environment variable
B<DISPLAY> contains the default display name.
I<x_offset> and I<y_offset> specify the offsets of the grabbed
area with respect to the top-left border of the X11 screen. They
default to 0.
Check the X11 documentation (e.g. man X) for more detailed information.
Use the B<dpyinfo> program for getting basic information about the
properties of your X11 display (e.g. grep for "name" or "dimensions").
For example to grab from F<:0.0> using B<ffmpeg>:
ffmpeg -f x11grab -framerate 25 -video_size cif -i :0.0 out.mpg
Grab at position C<10,20>:
ffmpeg -f x11grab -framerate 25 -video_size cif -i :0.0+10,20 out.mpg
=head3 Options
=over 4
=item B<draw_mouse>
Specify whether to draw the mouse pointer. A value of C<0> specify
not to draw the pointer. Default value is C<1>.
=item B<follow_mouse>
Make the grabbed area follow the mouse. The argument can be
C<centered> or a number of pixels I<PIXELS>.
When it is specified with "centered", the grabbing region follows the mouse
pointer and keeps the pointer at the center of region; otherwise, the region
follows only when the mouse pointer reaches within I<PIXELS> (greater than
zero) to the edge of region.
For example:
ffmpeg -f x11grab -follow_mouse centered -framerate 25 -video_size cif -i :0.0 out.mpg
To follow only when the mouse pointer reaches within 100 pixels to edge:
ffmpeg -f x11grab -follow_mouse 100 -framerate 25 -video_size cif -i :0.0 out.mpg
=item B<framerate>
Set the grabbing frame rate. Default value is C<ntsc>,
corresponding to a frame rate of C<30000/1001>.
=item B<show_region>
Show grabbed region on screen.
If I<show_region> is specified with C<1>, then the grabbing
region will be indicated on screen. With this option, it is easy to
know what is being grabbed if only a portion of the screen is grabbed.
For example:
ffmpeg -f x11grab -show_region 1 -framerate 25 -video_size cif -i :0.0+10,20 out.mpg
With I<follow_mouse>:
ffmpeg -f x11grab -follow_mouse centered -show_region 1 -framerate 25 -video_size cif -i :0.0 out.mpg
=item B<video_size>
Set the video frame size. Default value is C<vga>.
=back
=head1 OUTPUT DEVICES
Output devices are configured elements in FFmpeg that can write
multimedia data to an output device attached to your system.
When you configure your FFmpeg build, all the supported output devices
are enabled by default. You can list all available ones using the
configure option "--list-outdevs".
You can disable all the output devices using the configure option
"--disable-outdevs", and selectively enable an output device using the
option "--enable-outdev=I<OUTDEV>", or you can disable a particular
input device using the option "--disable-outdev=I<OUTDEV>".
The option "-formats" of the ff* tools will display the list of
enabled output devices (amongst the muxers).
A description of the currently available output devices follows.
=head2 alsa
ALSA (Advanced Linux Sound Architecture) output device.
=head2 caca
CACA output device.
This output device allows to show a video stream in CACA window.
Only one CACA window is allowed per application, so you can
have only one instance of this output device in an application.
To enable this output device you need to configure FFmpeg with
C<--enable-libcaca>.
libcaca is a graphics library that outputs text instead of pixels.
For more information about libcaca, check:
E<lt>B<http://caca.zoy.org/wiki/libcaca>E<gt>
=head3 Options
=over 4
=item B<window_title>
Set the CACA window title, if not specified default to the filename
specified for the output device.
=item B<window_size>
Set the CACA window size, can be a string of the form
I<width>xI<height> or a video size abbreviation.
If not specified it defaults to the size of the input video.
=item B<driver>
Set display driver.
=item B<algorithm>
Set dithering algorithm. Dithering is necessary
because the picture being rendered has usually far more colours than
the available palette.
The accepted values are listed with C<-list_dither algorithms>.
=item B<antialias>
Set antialias method. Antialiasing smoothens the rendered
image and avoids the commonly seen staircase effect.
The accepted values are listed with C<-list_dither antialiases>.
=item B<charset>
Set which characters are going to be used when rendering text.
The accepted values are listed with C<-list_dither charsets>.
=item B<color>
Set color to be used when rendering text.
The accepted values are listed with C<-list_dither colors>.
=item B<list_drivers>
If set to B<true>, print a list of available drivers and exit.
=item B<list_dither>
List available dither options related to the argument.
The argument must be one of C<algorithms>, C<antialiases>,
C<charsets>, C<colors>.
=back
=head3 Examples
=over 4
=item *
The following command shows the B<ffmpeg> output is an
CACA window, forcing its size to 80x25:
ffmpeg -i INPUT -vcodec rawvideo -pix_fmt rgb24 -window_size 80x25 -f caca -
=item *
Show the list of available drivers and exit:
ffmpeg -i INPUT -pix_fmt rgb24 -f caca -list_drivers true -
=item *
Show the list of available dither colors and exit:
ffmpeg -i INPUT -pix_fmt rgb24 -f caca -list_dither colors -
=back
=head2 fbdev
Linux framebuffer output device.
The Linux framebuffer is a graphic hardware-independent abstraction
layer to show graphics on a computer monitor, typically on the
console. It is accessed through a file device node, usually
F</dev/fb0>.
For more detailed information read the file
F<Documentation/fb/framebuffer.txt> included in the Linux source tree.
=head3 Options
=over 4
=item B<xoffset>
=item B<yoffset>
Set x/y coordinate of top left corner. Default is 0.
=back
=head3 Examples
Play a file on framebuffer device F</dev/fb0>.
Required pixel format depends on current framebuffer settings.
ffmpeg -re -i INPUT -vcodec rawvideo -pix_fmt bgra -f fbdev /dev/fb0
See also E<lt>B<http://linux-fbdev.sourceforge.net/>E<gt>, and fbset(1).
=head2 oss
OSS (Open Sound System) output device.
=head2 pulse
PulseAudio output device.
To enable this output device you need to configure FFmpeg with C<--enable-libpulse>.
More information about PulseAudio can be found on E<lt>B<http://www.pulseaudio.org>E<gt>
=head3 Options
=over 4
=item B<server>
Connect to a specific PulseAudio server, specified by an IP address.
Default server is used when not provided.
=item B<name>
Specify the application name PulseAudio will use when showing active clients,
by default it is the C<LIBAVFORMAT_IDENT> string.
=item B<stream_name>
Specify the stream name PulseAudio will use when showing active streams,
by default it is set to the specified output name.
=item B<device>
Specify the device to use. Default device is used when not provided.
List of output devices can be obtained with command B<pactl list sinks>.
=back
=head3 Examples
Play a file on default device on default server:
ffmpeg -i INPUT -f pulse "stream name"
=head2 sdl
SDL (Simple DirectMedia Layer) output device.
This output device allows to show a video stream in an SDL
window. Only one SDL window is allowed per application, so you can
have only one instance of this output device in an application.
To enable this output device you need libsdl installed on your system
when configuring your build.
For more information about SDL, check:
E<lt>B<http://www.libsdl.org/>E<gt>
=head3 Options
=over 4
=item B<window_title>
Set the SDL window title, if not specified default to the filename
specified for the output device.
=item B<icon_title>
Set the name of the iconified SDL window, if not specified it is set
to the same value of I<window_title>.
=item B<window_size>
Set the SDL window size, can be a string of the form
I<width>xI<height> or a video size abbreviation.
If not specified it defaults to the size of the input video,
downscaled according to the aspect ratio.
=item B<window_fullscreen>
Set fullscreen mode when non-zero value is provided.
Zero is a default.
=back
=head3 Examples
The following command shows the B<ffmpeg> output is an
SDL window, forcing its size to the qcif format:
ffmpeg -i INPUT -vcodec rawvideo -pix_fmt yuv420p -window_size qcif -f sdl "SDL output"
=head2 sndio
sndio audio output device.
=head2 xv
XV (XVideo) output device.
This output device allows to show a video stream in a X Window System
window.
=head3 Options
=over 4
=item B<display_name>
Specify the hardware display name, which determines the display and
communications domain to be used.
The display name or DISPLAY environment variable can be a string in
the format I<hostname>[:I<number>[.I<screen_number>]].
I<hostname> specifies the name of the host machine on which the
display is physically attached. I<number> specifies the number of
the display server on that host machine. I<screen_number> specifies
the screen to be used on that server.
If unspecified, it defaults to the value of the DISPLAY environment
variable.
For example, C<dual-headed:0.1> would specify screen 1 of display
0 on the machine named ``dual-headed''.
Check the X11 specification for more detailed information about the
display name format.
=item B<window_size>
Set the created window size, can be a string of the form
I<width>xI<height> or a video size abbreviation. If not
specified it defaults to the size of the input video.
=item B<window_x>
=item B<window_y>
Set the X and Y window offsets for the created window. They are both
set to 0 by default. The values may be ignored by the window manager.
=item B<window_title>
Set the window title, if not specified default to the filename
specified for the output device.
=back
For more information about XVideo see E<lt>B<http://www.x.org/>E<gt>.
=head3 Examples
=over 4
=item *
Decode, display and encode video input with B<ffmpeg> at the
same time:
ffmpeg -i INPUT OUTPUT -f xv display
=item *
Decode and display the input video to multiple X11 windows:
ffmpeg -i INPUT -f xv normal -vf negate -f xv negated
=back
=head1 SEE ALSO
ffmpeg(1), ffplay(1), ffprobe(1), ffserver(1), libavdevice(3)
=head1 AUTHORS
The FFmpeg developers.
For details about the authorship, see the Git history of the project
(git://source.ffmpeg.org/ffmpeg), e.g. by typing the command
B<git log> in the FFmpeg source directory, or browsing the
online repository at E<lt>B<http://source.ffmpeg.org>E<gt>.
Maintainers for the specific components are listed in the file
F<MAINTAINERS> in the source code tree.