kolibrios/kernel/trunk/network/eth_drv/drivers/r6040.inc

814 lines
19 KiB
PHP
Raw Normal View History

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Copyright (C) KolibriOS team 2004-2011. All rights reserved. ;;
;; Distributed under terms of the GNU General Public License ;;
;; ;;
;; R6040 driver for KolibriOS ;;
;; ;;
;; based on R6040.c from linux ;;
;; ;;
;; Written by Asper (asper.85@mail.ru) ;;
;; and hidnplayr (hidnplayr@gmail.com) ;;
;; ;;
;; GNU GENERAL PUBLIC LICENSE ;;
;; Version 2, June 1991 ;;
;; ;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;********************************************************************
; Interface
; r6040_reset
; r6040_probe
; r6040_poll
; r6040_transmit
;
; These functions are referenced in ethernet.inc
;
;********************************************************************
;; A few user-configurable values.
TX_RING_SIZE equ 4
RX_RING_SIZE equ 4
; ethernet address length
ETH_ALEN equ 6
ETH_HLEN equ (2 * ETH_ALEN + 2)
ETH_ZLEN equ 60 ; 60 + 4bytes auto payload for
; mininmum 64bytes frame length
; system timer frequency
HZ equ 1000
; max time out delay time
W_MAX_TIMEOUT equ 0x0FFF
;; Size of the in-memory receive ring.
RX_BUF_LEN_IDX equ 3 ;; 0==8K, 1==16K, 2==32K, 3==64K
RX_BUF_LEN equ (8192 << RX_BUF_LEN_IDX)
;-; Size of the Tx bounce buffers -- must be at least (dev->mtu+14+4).
;-TX_BUF_SIZE equ 1536
;-RX_BUF_SIZE equ 1536
;; PCI Tuning Parameters
; Threshold is bytes transferred to chip before transmission starts.
TX_FIFO_THRESH equ 256 ;; In bytes, rounded down to 32 byte units.
;; The following settings are log_2(bytes)-4: 0 == 16 bytes .. 6==1024.
RX_FIFO_THRESH equ 4 ;; Rx buffer level before first PCI xfer.
RX_DMA_BURST equ 4 ;; Maximum PCI burst, '4' is 256 bytes
TX_DMA_BURST equ 4
;; Operational parameters that usually are not changed.
PHY1_ADDR equ 1 ;For MAC1
PHY2_ADDR equ 3 ;For MAC2
PHY_MODE equ 0x3100 ;PHY CHIP Register 0
PHY_CAP equ 0x01E1 ;PHY CHIP Register 4
;; Time in jiffies before concluding the transmitter is hung.
TX_TIMEOUT equ ((6000*HZ)/1000)
R6040_IO_SIZE equ 256 ; RDC MAC I/O Size
MAX_MAC equ 2 ; MAX RDC MAC
;**************************************************************************
; RDC R6040 Register Definitions
;**************************************************************************
MCR0 equ 0x00 ;Control register 0
MCR1 equ 0x01 ;Control register 1
MAC_RST equ 0x0001 ;Reset the MAC
MBCR equ 0x08 ;Bus control
MT_ICR equ 0x0C ;TX interrupt control
MR_ICR equ 0x10 ;RX interrupt control
MTPR equ 0x14 ;TX poll command register
MR_BSR equ 0x18 ;RX buffer size
MR_DCR equ 0x1A ;RX descriptor control
MLSR equ 0x1C ;Last status
MMDIO equ 0x20 ;MDIO control register
MDIO_WRITE equ 0x4000 ;MDIO write
MDIO_READ equ 0x2000 ;MDIO read
MMRD equ 0x24 ;MDIO read data register
MMWD equ 0x28 ;MDIO write data register
MTD_SA0 equ 0x2C ;TX descriptor start address 0
MTD_SA1 equ 0x30 ;TX descriptor start address 1
MRD_SA0 equ 0x34 ;RX descriptor start address 0
MRD_SA1 equ 0x38 ;RX descriptor start address 1
MISR equ 0x3C ;Status register
MIER equ 0x40 ;INT enable register
MSK_INT equ 0x0000 ;Mask off interrupts
RX_FINISH equ 0x0001 ;RX finished
RX_NO_DESC equ 0x0002 ;No RX descriptor available
RX_FIFO_FULL equ 0x0004 ;RX FIFO full
RX_EARLY equ 0x0008 ;RX early
TX_FINISH equ 0x0010 ;TX finished
TX_EARLY equ 0x0080 ;TX early
EVENT_OVRFL equ 0x0100 ;Event counter overflow
LINK_CHANGED equ 0x0200 ;PHY link changed
ME_CISR equ 0x44 ;Event counter INT status
ME_CIER equ 0x48 ;Event counter INT enable
MR_CNT equ 0x50 ;Successfully received packet counter
ME_CNT0 equ 0x52 ;Event counter 0
ME_CNT1 equ 0x54 ;Event counter 1
ME_CNT2 equ 0x56 ;Event counter 2
ME_CNT3 equ 0x58 ;Event counter 3
MT_CNT equ 0x5A ;Successfully transmit packet counter
ME_CNT4 equ 0x5C ;Event counter 4
MP_CNT equ 0x5E ;Pause frame counter register
MAR0 equ 0x60 ;Hash table 0
MAR1 equ 0x62 ;Hash table 1
MAR2 equ 0x64 ;Hash table 2
MAR3 equ 0x66 ;Hash table 3
MID_0L equ 0x68 ;Multicast address MID0 Low
MID_0M equ 0x6A ;Multicast address MID0 Medium
MID_0H equ 0x6C ;Multicast address MID0 High
MID_1L equ 0x70 ;MID1 Low
MID_1M equ 0x72 ;MID1 Medium
MID_1H equ 0x74 ;MID1 High
MID_2L equ 0x78 ;MID2 Low
MID_2M equ 0x7A ;MID2 Medium
MID_2H equ 0x7C ;MID2 High
MID_3L equ 0x80 ;MID3 Low
MID_3M equ 0x82 ;MID3 Medium
MID_3H equ 0x84 ;MID3 High
PHY_CC equ 0x88 ;PHY status change configuration register
PHY_ST equ 0x8A ;PHY status register
MAC_SM equ 0xAC ;MAC status machine
MAC_ID equ 0xBE ;Identifier register
MAX_BUF_SIZE equ 0x600 ;1536
MBCR_DEFAULT equ 0x012A ;MAC Bus Control Register
MCAST_MAX equ 3 ;Max number multicast addresses to filter
;Descriptor status
DSC_OWNER_MAC equ 0x8000 ;MAC is the owner of this descriptor
DSC_RX_OK equ 0x4000 ;RX was successfull
DSC_RX_ERR equ 0x0800 ;RX PHY error
DSC_RX_ERR_DRI equ 0x0400 ;RX dribble packet
DSC_RX_ERR_BUF equ 0x0200 ;RX length exceeds buffer size
DSC_RX_ERR_LONG equ 0x0100 ;RX length > maximum packet length
DSC_RX_ERR_RUNT equ 0x0080 ;RX packet length < 64 byte
DSC_RX_ERR_CRC equ 0x0040 ;RX CRC error
DSC_RX_BCAST equ 0x0020 ;RX broadcast (no error)
DSC_RX_MCAST equ 0x0010 ;RX multicast (no error)
DSC_RX_MCH_HIT equ 0x0008 ;RX multicast hit in hash table (no error)
DSC_RX_MIDH_HIT equ 0x0004 ;RX MID table hit (no error)
DSC_RX_IDX_MID_MASK equ 3 ;RX mask for the index of matched MIDx
;PHY settings
ICPLUS_PHY_ID equ 0x0243
RX_INTS equ RX_FIFO_FULL or RX_NO_DESC or RX_FINISH
TX_INTS equ TX_FINISH
INT_MASK equ RX_INTS or TX_INTS
r6040_txb equ (eth_data_start)
r6040_rxb equ ((r6040_txb+(MAX_BUF_SIZE*TX_RING_SIZE)+32) and 0xfffffff0)
r6040_tx_ring equ ((r6040_rxb+(MAX_BUF_SIZE*RX_RING_SIZE)+32) and 0xfffffff0)
r6040_rx_ring equ ((r6040_tx_ring+(r6040_x_head.sizeof*TX_RING_SIZE)+32) and 0xfffffff0)
virtual at ((r6040_rx_ring+(r6040_x_head.sizeof*RX_RING_SIZE)+32) and 0xfffffff0)
r6040_private:
.rx_ring dd ?
.tx_ring dd ?
.cur_rx dw ?
.cur_tx dw ?
.phy_addr dw ?
.phy_mode dw ?
.mcr0 dw ?
.mcr1 dw ?
.switch_sig dw ?
end virtual
virtual at 0
r6040_x_head:
.status dw ? ;0-1
.len dw ? ;2-3
.buf dd ? ;4-7
.ndesc dd ? ;8-B
.rev1 dd ? ;C-F
.vbufp dd ? ;10-13
.vndescp dd ? ;14-17
.skb_ptr dd ? ;18-1B
.rev2 dd ? ;1C-1F
.sizeof:
end virtual
; Read a word data from PHY Chip
proc r6040_phy_read stdcall, phy_addr:dword, reg:dword
push ecx edx
mov eax, [phy_addr]
shl eax, 8
add eax, [reg]
add eax, MDIO_READ
mov edx, [io_addr]
add edx, MMDIO
out dx, ax
;Wait for the read bit to be cleared.
mov ecx, 2048 ;limit
xor eax, eax
.read:
in ax, dx
test ax, MDIO_READ
jz @f
dec ecx
test ecx, ecx
jnz .read
@@:
mov edx, [io_addr]
add edx, MMRD
in ax, dx
and eax, 0xFFFF
pop edx ecx
ret
endp
; Write a word data to PHY Chip
proc r6040_phy_write stdcall, phy_addr:dword, reg:dword, val:dword
push eax ecx edx
mov eax, [val]
mov edx, [io_addr]
add edx, MMWD
out dx, ax
;Write the command to the MDIO bus
mov eax, [phy_addr]
shl eax, 8
add eax, [reg]
add eax, MDIO_WRITE
mov edx, [io_addr]
add edx, MMDIO
out dx, ax
;Wait for the write bit to be cleared.
mov ecx, 2048 ;limit
xor eax, eax
.write:
in ax, dx
test ax, MDIO_WRITE
jz @f
dec ecx
test ecx, ecx
jnz .write
@@:
pop edx ecx eax
ret
endp
macro r6040_mdio_write reg, val {
stdcall r6040_phy_read, [io_addr], [r6040_private.phy_addr], reg
}
macro r6040_mdio_write reg, val {
stdcall r6040_phy_write, [io_addr], [r6040_private.phy_addr], reg, val
}
proc r6040_init_ring_desc stdcall, desc_ring:dword, size:dword
push eax ecx esi
mov ecx, [size]
test ecx, ecx
jz .out
mov esi, [desc_ring]
mov eax, esi
.next_desc:
add eax, r6040_x_head.sizeof - OS_BASE
mov [esi+r6040_x_head.ndesc], eax
add eax, OS_BASE
mov [esi+r6040_x_head.vndescp], eax
mov esi, eax
dec ecx
jnz .next_desc
sub esi, r6040_x_head.sizeof
mov eax, [desc_ring]
mov [esi+r6040_x_head.vndescp], eax
sub eax, OS_BASE
mov [esi+r6040_x_head.ndesc], eax
.out:
pop esi ecx eax
ret
endp
r6040_init_rxbufs:
stdcall r6040_init_ring_desc, r6040_rx_ring, RX_RING_SIZE
; Allocate skbs for the rx descriptors
mov esi, r6040_rx_ring
mov ebx, r6040_rxb
mov ecx, RX_RING_SIZE
mov eax, r6040_rx_ring
.next_desc:
mov [esi+r6040_x_head.skb_ptr], ebx
mov [esi+r6040_x_head.buf], ebx
sub [esi+r6040_x_head.buf], OS_BASE
mov [esi+r6040_x_head.status], DSC_OWNER_MAC
mov eax, [esi+r6040_x_head.vndescp]
mov esi, eax
add ebx, MAX_BUF_SIZE
dec ecx
jnz .next_desc
xor eax, eax
.out:
ret
r6040_probe:
DEBUGF 1, "Probing r6040\n"
call adjust_pci_device
; If PHY status change register is still set to zero
; it means the bootloader didn't initialize it
mov edx, [io_addr]
add edx, PHY_CC
in ax, dx
test ax, ax
jnz @f
mov eax, 0x9F07
out dx, ax
@@:
; Set MAC address
mov ecx, 3
mov edi, node_addr
mov edx, [io_addr]
add edx, MID_0L
.mac:
in ax, dx
stosw
add edx, 2
dec ecx
jnz .mac
; Some bootloaders/BIOSes do not initialize
; MAC address, warn about that
and eax, 0xFF
or eax, [node_addr]
test eax, eax
jnz @f
DEBUGF 1, "K : MAC address not initialized\n" ;, generating random"
;Asper: Add here generate function call!
; Temporary workaround: init by constant adress
mov dword [node_addr], 0x00006000
mov word [node_addr+4], 0x0001
@@:
; Init RDC private data
mov [r6040_private.mcr0], 0x1002
;mov [r6040_private.phy_addr], 1 ; Asper: Only one network card is supported now.
mov [r6040_private.switch_sig], 0
; Check the vendor ID on the PHY, if 0xFFFF assume none attached
stdcall r6040_phy_read, 1, 2
cmp ax, 0xFFFF
jne @f
DEBUGF 1, "K : Failed to detect an attached PHY\n" ;, generating random"
mov eax, -1
ret
@@:
; Set MAC address
call r6040_mac_address
; Initialize and alloc RX/TX buffers
stdcall r6040_init_ring_desc, r6040_tx_ring, TX_RING_SIZE
call r6040_init_rxbufs ;r6040_alloc_rxbufs
test eax, eax
jnz .out
; Read the PHY ID
mov [r6040_private.phy_mode], 0x8000
stdcall r6040_phy_read, 0, 2
mov [r6040_private.switch_sig], ax
cmp ax, ICPLUS_PHY_ID
jne @f
stdcall r6040_phy_write, 29, 31, 0x175C ; Enable registers
jmp .phy_readen
@@:
; PHY Mode Check
movzx eax, [r6040_private.phy_addr]
stdcall r6040_phy_write, eax, 4, PHY_CAP
stdcall r6040_phy_write, eax, 0, PHY_MODE
; if PHY_MODE = 0x3100
call r6040_phy_mode_chk
mov [r6040_private.phy_mode], ax
jmp .phy_readen
; end if
; if not (PHY_MODE and 0x0100)
mov [r6040_private.phy_mode], 0
; end if
.phy_readen:
; Set duplex mode
mov ax, [r6040_private.phy_mode]
or [r6040_private.mcr0], ax
; improve performance (by RDC guys)
stdcall r6040_phy_read, 30, 17
or ax, 0x4000
stdcall r6040_phy_write, 30, 17, eax
stdcall r6040_phy_read, 30, 17
xor ax, -1
or ax, 0x2000
xor ax, -1
stdcall r6040_phy_write, 30, 17, eax
stdcall r6040_phy_write, 0, 19, 0x0000
stdcall r6040_phy_write, 0, 30, 0x01F0
; Initialize all Mac registers
call r6040_reset
xor eax, eax
.out:
ret
align 4
r6040_reset:
DEBUGF 1, "Resetting r6040\n"
push eax ecx edx
; Mask off Interrupt
mov eax, MSK_INT
mov edx, [io_addr]
add edx, MIER
out dx, ax
;Reset RDC MAC
mov eax, MAC_RST
mov edx, [io_addr]
add edx, MCR1
out dx, ax
mov ecx, 2048 ;limit
.read:
in ax, dx
test ax, 0x1
jnz @f
dec ecx
test ecx, ecx
jnz .read
@@:
;Reset internal state machine
mov ax, 2
mov edx, [io_addr]
add edx, MAC_SM
out dx, ax
xor ax, ax
out dx, ax
mov esi, 5
call delay_ms
;MAC Bus Control Register
mov ax, MBCR_DEFAULT
mov edx, [io_addr]
add edx, MBCR
out dx, ax
;Buffer Size Register
mov ax, MAX_BUF_SIZE
mov edx, [io_addr]
add edx, MR_BSR
out dx, ax
;Write TX ring start address
mov eax, r6040_tx_ring - OS_BASE ;Asper: Maybe we can just write dword? Hidnplayr: better use word, as described in datasheet.
mov edx, [io_addr]
add edx, MTD_SA0
out dx, ax
shr eax, 16
add edx, MTD_SA1 - MTD_SA0
out dx, ax
;Write RX ring start address
mov eax, r6040_rx_ring - OS_BASE ;Asper: Maybe we can just write dword?
mov edx, [io_addr]
add edx, MRD_SA0
out dx, ax
shr eax, 16
add edx, MRD_SA1 - MRD_SA0
out dx, ax
;Set interrupt waiting time and packet numbers
xor ax, ax
mov edx, [io_addr]
add edx, MT_ICR
out dx, ax
;Asper: ~ Disable ints ;Enable interrupts
;mov ax, MSK_INT ;INT_MASK ;Asper ~
;mov edx, [io_addr]
;add edx, MIER
;out dx, ax
;Enable TX and RX
mov ax, [r6040_private.mcr0]
or ax, 0x0002
mov edx, [io_addr]
out dx, ax
;Let TX poll the descriptors
;we may got called by r6040_tx_timeout which has left
;some unset tx buffers
xor ax, ax
inc ax
mov edx, [io_addr]
add edx, MTPR
out dx, ax
pop edx ecx eax
DEBUGF 1, "reset ok!\n"
; Indicate that we have successfully reset the card
mov eax, [pci_data]
mov [eth_status], eax
ret
proc r6040_tx_timeout
push eax edx
;...
inc [stats.tx_errors]
;Reset MAC and re-init all registers
call r6040_init_mac_regs
pop edx eax
ret
endp
proc r6040_get_stats
push eax edx
mov edx, [io_addr]
add edx, ME_CNT1
in al, dx
add [stats.rx_crc_errors], al
mov edx, [io_addr]
add edx, ME_CNT0
in al, dx
add [stats.multicast], al
pop edx eax
ret
endp
;...
proc r6040_phy_mode_chk
push ebx
;PHY Link Status Check
movzx eax, [r6040_private.phy_addr]
stdcall r6040_phy_read, eax, 1
test eax, 0x4
jnz @f
mov eax, 0x8000 ;Link Failed, full duplex
@@:
;PHY Chip Auto-Negotiation Status
movzx eax, [r6040_private.phy_addr]
stdcall r6040_phy_read, eax, 1
test eax, 0x0020
jz .force_mode
;Auto Negotuiation Mode
movzx eax, [r6040_private.phy_addr]
stdcall r6040_phy_read, eax, 5
mov ebx, eax
movzx eax, [r6040_private.phy_addr]
stdcall r6040_phy_read, eax, 4
and eax, ebx
test eax, 0x140
jz .ret_0
jmp .ret_0x8000
.force_mode:
;Force Mode
movzx eax, [r6040_private.phy_addr]
stdcall r6040_phy_read, eax, 0
test eax, 0x100
jz .ret_0
.ret_0x8000:
mov eax, 0x8000
pop ebx
ret
.ret_0:
xor eax, eax
pop ebx
ret
endp
;***************************************************************************
; Function
; r6040_rx
; Description
; polls card to see if there is a packet waiting
;
; Currently only supports one descriptor per packet, if packet is fragmented
; between multiple descriptors you will lose part of the packet
;***************************************************************************
r6040_poll:
push ebx ecx esi edi
xor eax, eax
mov [eth_rx_data_len], ax
movzx eax, [r6040_private.cur_rx]
mov ebx, eax
shl ebx, 5
mov cx, [ebx+r6040_rx_ring+r6040_x_head.status] ; Read the descriptor status
test cx, DSC_OWNER_MAC
jnz .out
test cx, DSC_RX_ERR ; Global error status set
jz .no_dsc_rx_err
;...
jmp .out
.no_dsc_rx_err:
; Packet successfully received
movzx ecx, [ebx+r6040_rx_ring+r6040_x_head.len]
and ecx, 0xFFF
sub ecx, 4 ; Do not count the CRC
mov [eth_rx_data_len], cx
mov esi, [ebx+r6040_rx_ring+r6040_x_head.skb_ptr]
push ecx
shr ecx, 2
mov edi, Ether_buffer
cld
rep movsd
pop ecx
and ecx, 3
rep movsb
or [ebx+r6040_rx_ring+r6040_x_head.status], DSC_OWNER_MAC
inc [r6040_private.cur_rx]
and [r6040_private.cur_rx], RX_RING_SIZE-1
xor eax, eax
.out:
pop edi esi ecx ebx
ret
;***************************************************************************
; Function
; r6040_transmit
; Description
; Transmits a packet of data via the ethernet card
; Pointer to 48 bit destination address in edi
; Type of packet in bx
; size of packet in ecx
; pointer to packet data in esi
;
;***************************************************************************
r6040_transmit:
cmp ecx, MAX_BUF_SIZE
jg .out ; packet is too long
push edi esi ebx ecx
movzx eax, [r6040_private.cur_tx]
shl eax, 5
; DEBUGF 1,"R6040: TX buffer status: 0x%x, eax=%u\n", [eax + r6040_tx_ring + r6040_x_head.status]:4, eax
test [r6040_tx_ring + eax + r6040_x_head.status], 0x8000 ; check if buffer is available
jz .l3
push ecx esi
mov ecx, [timer_ticks]
add ecx, 100
.l2:
test [r6040_tx_ring + eax + r6040_x_head.status], 0x8000
jz .l5
cmp ecx, [timer_ticks]
jb .l4
mov esi, 10
call delay_ms
jmp .l2
.l4:
pop esi ecx
DEBUGF 1,"R6040: Send timeout\n"
jmp .out
.l5:
pop esi ecx
.l3:
push eax
mov esi, edi
; point to the current tx buffer
movzx edi, [r6040_private.cur_tx]
imul edi, MAX_BUF_SIZE
add edi, r6040_txb
lea eax, [edi - OS_BASE] ; real buffer address in eax
; copy destination address
movsd
movsw
; copy source address
mov esi, node_addr
movsd
movsw
; copy packet type
mov [edi], bx
add edi, 2
mov esi, [esp+8+4]
mov ecx, [esp+4]
; copy the packet data
push ecx
shr ecx,2
rep movsd
pop ecx
and ecx,3
rep movsb
pop edi
mov ecx, [esp]
add ecx, ETH_HLEN
cmp cx, ETH_ZLEN
jae @f
mov cx, ETH_ZLEN
@@:
mov [r6040_tx_ring + edi + r6040_x_head.len], cx
mov [r6040_tx_ring + edi + r6040_x_head.buf], eax
mov [r6040_tx_ring + edi + r6040_x_head.status], 0x8000
; Trigger the MAC to check the TX descriptor
mov ax, 0x01
mov edx, [io_addr]
add edx, MTPR
out dx, ax
inc [r6040_private.cur_tx]
and [r6040_private.cur_tx], TX_RING_SIZE-1
xor eax, eax
pop ecx ebx esi edi
.out:
ret
r6040_mac_address:
push eax ecx edx esi edi
; MAC operation register
mov ax, 1
mov edx, [io_addr]
add edx, MCR1
out dx, ax
; Reset MAC
mov ax, 2
mov edx, [io_addr]
add edx, MAC_SM
out dx, ax
; Reset internal state machine
xor ax, ax
out dx, ax
mov esi, 5
call delay_ms
; Restore MAC Address
mov ecx, 3
mov edi, node_addr
mov edx, [io_addr]
add edx, MID_0L
.mac:
in ax, dx
stosw
add edx, 2
dec ecx
jnz .mac
pop edi esi edx ecx eax
ret