forked from KolibriOS/kolibrios
Replaced signed relative jumps with unsigned ones were needed.
(I must lose this bad habbit in 2013...) git-svn-id: svn://kolibrios.org@3155 a494cfbc-eb01-0410-851d-a64ba20cac60
This commit is contained in:
hidnplayr
parent
1dfb449935
commit
efb37b3598
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2010. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; 3Com network driver for KolibriOS ;;
|
||||
@ -374,7 +374,7 @@ proc START stdcall, state:dword
|
||||
|
||||
.entry:
|
||||
|
||||
DEBUGF 1,"Loading 3com network driver\n"
|
||||
DEBUGF 1,"Loading %s driver\n", my_service
|
||||
stdcall RegService, my_service, service_proc
|
||||
ret
|
||||
|
||||
@ -408,7 +408,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -421,7 +421,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne .fail
|
||||
|
||||
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
||||
@ -465,7 +465,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
mov ecx, [BOOMERANG_DEVICES]
|
||||
add ecx, [VORTEX_DEVICES]
|
||||
cmp ecx, MAX_DEVICES ; First check if the driver can handle one more card
|
||||
jge .fail
|
||||
jae .fail
|
||||
|
||||
allocate_and_clear ebx, device.size, .fail ; Allocate the buffer for device structure
|
||||
|
||||
@ -2270,7 +2270,7 @@ boomerang_transmit:
|
||||
[eax+13]:2,[eax+12]:2
|
||||
|
||||
cmp dword [esp+8], MAX_ETH_FRAME_SIZE
|
||||
jg .fail
|
||||
ja .fail
|
||||
|
||||
call check_tx_status
|
||||
|
||||
@ -2280,7 +2280,7 @@ boomerang_transmit:
|
||||
add esi, dpd.size
|
||||
lea ecx, [device.dpd_buffer + (NUM_TX_DESC)*dpd.size]
|
||||
cmp esi, ecx
|
||||
jl @f
|
||||
jb @f
|
||||
lea esi, [device.dpd_buffer] ; Wrap if needed
|
||||
@@:
|
||||
DEBUGF 1,"Found a free DPD: %x\n", esi
|
||||
@ -2740,7 +2740,7 @@ int_boomerang:
|
||||
add esi, upd.size
|
||||
lea ecx, [device.upd_buffer+(NUM_RX_DESC)*upd.size]
|
||||
cmp esi, ecx
|
||||
jl @f
|
||||
jb @f
|
||||
lea esi, [device.upd_buffer]
|
||||
@@:
|
||||
mov [device.curr_upd], esi
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2011. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; R6040 driver for KolibriOS ;;
|
||||
@ -224,7 +224,7 @@ proc START stdcall, state:dword
|
||||
|
||||
.entry:
|
||||
|
||||
DEBUGF 2,"Loading R6040 driver\n"
|
||||
DEBUGF 2,"Loading %s driver\n", my_service
|
||||
stdcall RegService, my_service, service_proc
|
||||
ret
|
||||
|
||||
@ -255,7 +255,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -268,7 +268,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne .fail
|
||||
|
||||
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
||||
@ -294,7 +294,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
; This device doesnt have its own eth_device structure yet, lets create one
|
||||
.firstdevice:
|
||||
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
|
||||
jge .fail
|
||||
jae .fail
|
||||
|
||||
allocate_and_clear ebx, device.size, .fail ; Allocate the buffer for device structure
|
||||
|
||||
@ -756,9 +756,9 @@ transmit:
|
||||
[eax+13]:2,[eax+12]:2
|
||||
|
||||
cmp dword [esp+8], 1514
|
||||
jg .fail
|
||||
ja .fail
|
||||
cmp dword [esp+8], 60
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
movzx edi, [device.cur_tx]
|
||||
shl edi, 5
|
||||
@ -813,7 +813,7 @@ transmit:
|
||||
call Sleep
|
||||
call GetTimerTicks
|
||||
cmp edx, eax
|
||||
jl .l2
|
||||
jb .l2
|
||||
|
||||
DEBUGF 1,"Send timeout\n"
|
||||
xor eax, eax
|
||||
|
||||
@ -198,7 +198,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F ;---------------
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -215,12 +215,12 @@ proc service_proc stdcall, ioctl:dword
|
||||
mov eax, [IOCTL.input]
|
||||
|
||||
cmp [IOCTL.inp_size], 3
|
||||
jl .fail
|
||||
jb .fail
|
||||
cmp byte [eax], 1
|
||||
je .pci
|
||||
|
||||
cmp [IOCTL.inp_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
cmp byte [eax], 0
|
||||
je .isa
|
||||
|
||||
@ -674,9 +674,9 @@ transmit:
|
||||
[esi+0]:2,[esi+1]:2,[esi+2]:2,[esi+3]:2,[esi+4]:2,[esi+5]:2,[esi+6]:2,[esi+7]:2,[esi+8]:2,[esi+9]:2,[esi+10]:2,[esi+11]:2,[esi+13]:2,[esi+12]:2
|
||||
|
||||
cmp ecx, ETH_FRAME_LEN
|
||||
jg .err ; packet is too long
|
||||
ja .err ; packet is too long
|
||||
cmp ecx, ETH_ZLEN
|
||||
jl .err ; packet is too short
|
||||
jb .err ; packet is too short
|
||||
|
||||
movzx edi, [device.tx_start]
|
||||
shl edi, 8
|
||||
@ -1171,11 +1171,11 @@ devices dd 0
|
||||
version dd (DRIVER_VERSION shl 16) or (API_VERSION and 0xFFFF)
|
||||
my_service db 'RTL8029/ne2000',0 ;max 16 chars include zero
|
||||
|
||||
device_1 db 'Realtek 8029',0
|
||||
device_2 db 'Realtek 8019',0
|
||||
device_3 db 'Realtek 8019AS',0
|
||||
device_4 db 'ne2000',0
|
||||
device_5 db 'DP8390',0
|
||||
;device_1 db 'Realtek 8029',0
|
||||
;device_2 db 'Realtek 8019',0
|
||||
;device_3 db 'Realtek 8019AS',0
|
||||
;device_4 db 'ne2000',0
|
||||
;device_5 db 'DP8390',0
|
||||
|
||||
include_debug_strings
|
||||
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2010. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; Realtek 8139 driver for KolibriOS ;;
|
||||
@ -23,14 +23,16 @@ format MS COFF
|
||||
MAX_DEVICES = 16
|
||||
|
||||
RBLEN = 3 ; Receive buffer size: 0==8K 1==16k 2==32k 3==64k
|
||||
NUM_TX_DESC = 4
|
||||
|
||||
DEBUG = 1
|
||||
__DEBUG__ = 1
|
||||
__DEBUG_LEVEL__ = 2
|
||||
__DEBUG_LEVEL__ = 1
|
||||
|
||||
include 'proc32.inc'
|
||||
include 'imports.inc'
|
||||
include 'fdo.inc'
|
||||
include '../struct.inc'
|
||||
include 'netdrv.inc'
|
||||
|
||||
public START
|
||||
@ -135,8 +137,7 @@ public version
|
||||
(1 shl BIT_AM) ; Accept multicast packets
|
||||
|
||||
RX_BUFFER_SIZE = (8192 shl RBLEN);+16
|
||||
MAX_ETH_FRAME_SIZE = 1516 ; exactly 1514 wthout CRC
|
||||
NUM_TX_DESC = 4
|
||||
MAX_ETH_FRAME_SIZE = 1514
|
||||
|
||||
EE_93C46_REG_ETH_ID = 7 ; MAC offset
|
||||
EE_93C46_READ_CMD = (6 shl 6) ; 110b + 6bit address
|
||||
@ -237,7 +238,7 @@ proc START stdcall, state:dword
|
||||
|
||||
.entry:
|
||||
|
||||
DEBUGF 2,"Loading rtl8139 driver\n"
|
||||
DEBUGF 2, "Loading %s driver\n", my_service
|
||||
stdcall RegService, my_service, service_proc
|
||||
ret
|
||||
|
||||
@ -268,7 +269,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -281,7 +282,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne .fail
|
||||
|
||||
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
||||
@ -306,7 +307,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
; This device doesnt have its own eth_device structure yet, lets create one
|
||||
.firstdevice:
|
||||
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
|
||||
jge .fail
|
||||
jae .fail
|
||||
|
||||
allocate_and_clear ebx, device.size, .fail ; Allocate the buffer for device structure
|
||||
|
||||
@ -322,9 +323,9 @@ proc service_proc stdcall, ioctl:dword
|
||||
; save the pci bus and device numbers
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
mov cl , [eax+1]
|
||||
mov cl, [eax+1]
|
||||
mov [device.pci_bus], cl
|
||||
mov cl , [eax+2]
|
||||
mov cl, [eax+2]
|
||||
mov [device.pci_dev], cl
|
||||
|
||||
; Now, it's time to find the base io addres of the PCI device
|
||||
@ -335,7 +336,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
|
||||
find_irq [device.pci_bus], [device.pci_dev], [device.irq_line]
|
||||
|
||||
DEBUGF 2,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\
|
||||
DEBUGF 2, "Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\
|
||||
[device.pci_dev]:1,[device.pci_bus]:1,[device.irq_line]:1,[device.io_addr]:4
|
||||
|
||||
; Allocate the receive buffer
|
||||
@ -366,11 +367,11 @@ proc service_proc stdcall, ioctl:dword
|
||||
; If the device was already loaded, find the device number and return it in eax
|
||||
|
||||
.find_devicenum:
|
||||
DEBUGF 2,"Trying to find device number of already registered device\n"
|
||||
DEBUGF 2, "Trying to find device number of already registered device\n"
|
||||
call NetPtrToNum ; This kernel procedure converts a pointer to device struct in ebx
|
||||
; into a device number in edi
|
||||
mov eax, edi ; Application wants it in eax instead
|
||||
DEBUGF 2,"Kernel says: %u\n", eax
|
||||
DEBUGF 2, "Kernel says: %u\n", eax
|
||||
ret
|
||||
|
||||
; If an error occured, remove all allocated data and exit (returning -1 in eax)
|
||||
@ -379,7 +380,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
; todo: reset device into virgin state
|
||||
|
||||
.err:
|
||||
stdcall KernelFree, dword [device.rx_buffer]
|
||||
stdcall KernelFree, [device.rx_buffer]
|
||||
stdcall KernelFree, ebx
|
||||
|
||||
.fail:
|
||||
@ -406,7 +407,7 @@ unload:
|
||||
; - call unregister function in kernel
|
||||
; - Remove all allocated structures and buffers the card used
|
||||
|
||||
or eax,-1
|
||||
or eax, -1
|
||||
|
||||
ret
|
||||
|
||||
@ -419,7 +420,7 @@ ret
|
||||
|
||||
align 4
|
||||
probe:
|
||||
DEBUGF 2,"Probing rtl8139 device: "
|
||||
DEBUGF 2, "Probing %s device\n", my_service
|
||||
|
||||
make_bus_master [device.pci_bus], [device.pci_dev]
|
||||
|
||||
@ -427,14 +428,14 @@ probe:
|
||||
|
||||
set_io 0
|
||||
set_io REG_TXCONFIG + 2
|
||||
in ax , dx
|
||||
shr ah , 2
|
||||
shr ax , 6
|
||||
and al , 01111111b
|
||||
in ax, dx
|
||||
shr ah, 2
|
||||
shr ax, 6
|
||||
and al, 01111111b
|
||||
|
||||
mov ecx, HW_VER_ARRAY_SIZE-1
|
||||
.chip_ver_loop:
|
||||
cmp al , [hw_ver_array + ecx]
|
||||
cmp al, [hw_ver_array + ecx]
|
||||
je .chip_ver_found
|
||||
dec ecx
|
||||
jns .chip_ver_loop
|
||||
@ -442,65 +443,65 @@ probe:
|
||||
mov ecx, 8
|
||||
.chip_ver_found:
|
||||
cmp ecx, 8
|
||||
jg .unknown
|
||||
ja .unknown
|
||||
|
||||
mov [device.hw_ver_id], cl
|
||||
|
||||
mov ecx, [crosslist + ecx*4]
|
||||
mov ecx, [crosslist+ecx*4]
|
||||
mov [device.name], ecx
|
||||
|
||||
DEBUGF 2,"Chip version: %s\n", ecx
|
||||
DEBUGF 2, "Chip version: %s\n", ecx
|
||||
|
||||
; wake up the chip
|
||||
|
||||
set_io 0
|
||||
set_io REG_HLTCLK
|
||||
mov al , 'R' ; run the clock
|
||||
out dx , al
|
||||
mov al, 'R' ; run the clock
|
||||
out dx, al
|
||||
|
||||
; unlock config and BMCR registers
|
||||
|
||||
set_io REG_9346CR
|
||||
mov al , (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EEM0)
|
||||
out dx , al
|
||||
mov al, (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EEM0)
|
||||
out dx, al
|
||||
|
||||
; enable power management
|
||||
|
||||
set_io REG_CONFIG1
|
||||
in al , dx
|
||||
in al, dx
|
||||
cmp [device.hw_ver_id], IDX_RTL8139B
|
||||
jl .old_chip
|
||||
jb .old_chip
|
||||
|
||||
; set LWAKE pin to active high (default value).
|
||||
; it is for Wake-On-LAN functionality of some motherboards.
|
||||
; this signal is used to inform the motherboard to execute a wake-up process.
|
||||
; only at newer chips.
|
||||
|
||||
or al , (1 shl BIT_PMEn)
|
||||
and al , not (1 shl BIT_LWACT)
|
||||
out dx , al
|
||||
or al, (1 shl BIT_PMEn)
|
||||
and al, not (1 shl BIT_LWACT)
|
||||
out dx, al
|
||||
|
||||
set_io REG_CONFIG4
|
||||
in al , dx
|
||||
and al , not (1 shl BIT_LWPTN)
|
||||
out dx , al
|
||||
in al, dx
|
||||
and al, not (1 shl BIT_LWPTN)
|
||||
out dx, al
|
||||
|
||||
jmp .finish_wake_up
|
||||
.old_chip:
|
||||
|
||||
; wake up older chips
|
||||
|
||||
and al , not ((1 shl BIT_SLEEP) or (1 shl BIT_PWRDWN))
|
||||
out dx , al
|
||||
and al, not ((1 shl BIT_SLEEP) or (1 shl BIT_PWRDWN))
|
||||
out dx, al
|
||||
.finish_wake_up:
|
||||
|
||||
; lock config and BMCR registers
|
||||
|
||||
xor al , al
|
||||
xor al, al
|
||||
set_io 0
|
||||
set_io REG_9346CR
|
||||
out dx , al
|
||||
DEBUGF 2,"done!\n"
|
||||
out dx, al
|
||||
DEBUGF 2, "done!\n"
|
||||
|
||||
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
@ -510,23 +511,23 @@ probe:
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
|
||||
reset:
|
||||
DEBUGF 2,"Resetting rtl8139\n"
|
||||
DEBUGF 2, "Resetting\n"
|
||||
|
||||
; attach int handler
|
||||
|
||||
movzx eax, [device.irq_line]
|
||||
DEBUGF 1,"Attaching int handler to irq %x, ",eax:1
|
||||
DEBUGF 1, "Attaching int handler to irq %x, ", eax:1
|
||||
stdcall AttachIntHandler, eax, int_handler, dword 0
|
||||
test eax, eax
|
||||
jnz @f
|
||||
DEBUGF 1,"\nCould not attach int handler!\n"
|
||||
DEBUGF 1, "\nCould not attach int handler!\n"
|
||||
; or eax, -1
|
||||
; ret
|
||||
@@:
|
||||
|
||||
; reset chip
|
||||
|
||||
DEBUGF 1,"Resetting chip\n"
|
||||
DEBUGF 1, "Resetting chip\n"
|
||||
set_io 0
|
||||
set_io REG_COMMAND
|
||||
mov al , 1 shl BIT_RST
|
||||
@ -543,56 +544,56 @@ reset:
|
||||
; unlock config and BMCR registers
|
||||
|
||||
set_io REG_9346CR
|
||||
mov al , (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EEM0)
|
||||
out dx , al
|
||||
mov al, (1 shl BIT_93C46_EEM1) or (1 shl BIT_93C46_EEM0)
|
||||
out dx, al
|
||||
|
||||
; initialize multicast registers (no filtering)
|
||||
|
||||
mov eax, 0xffffffff
|
||||
set_io REG_MAR0
|
||||
out dx , eax
|
||||
out dx, eax
|
||||
set_io REG_MAR4
|
||||
out dx , eax
|
||||
out dx, eax
|
||||
|
||||
; enable Rx/Tx
|
||||
|
||||
mov al , (1 shl BIT_RE) or (1 shl BIT_TE)
|
||||
mov al, (1 shl BIT_RE) or (1 shl BIT_TE)
|
||||
set_io REG_COMMAND
|
||||
out dx , al
|
||||
out dx, al
|
||||
|
||||
; Rxbuffer size, unlimited dma burst, no wrapping, no rx threshold
|
||||
; accept broadcast packets, accept physical match packets
|
||||
|
||||
mov ax , RX_CONFIG
|
||||
mov ax, RX_CONFIG
|
||||
set_io REG_RXCONFIG
|
||||
out dx , ax
|
||||
out dx, ax
|
||||
|
||||
|
||||
; 1024 bytes DMA burst, total retries = 16 + 8 * 16 = 144
|
||||
|
||||
mov eax , (TX_MXDMA shl BIT_TX_MXDMA) or (TXRR shl BIT_TXRR) or BIT_IFG1 or BIT_IFG0
|
||||
mov eax, (TX_MXDMA shl BIT_TX_MXDMA) or (TXRR shl BIT_TXRR) or BIT_IFG1 or BIT_IFG0
|
||||
set_io REG_TXCONFIG
|
||||
out dx , eax
|
||||
out dx, eax
|
||||
|
||||
; enable auto negotiation
|
||||
|
||||
set_io REG_BMCR
|
||||
in ax , dx
|
||||
or ax , (1 shl BIT_ANE)
|
||||
out dx , ax
|
||||
in ax, dx
|
||||
or ax, (1 shl BIT_ANE)
|
||||
out dx, ax
|
||||
|
||||
; set auto negotiation advertisement
|
||||
|
||||
set_io REG_ANAR
|
||||
in ax , dx
|
||||
or ax , (1 shl BIT_SELECTOR) or (1 shl BIT_10) or (1 shl BIT_10FD) or (1 shl BIT_TX) or (1 shl BIT_TXFD)
|
||||
out dx , ax
|
||||
in ax, dx
|
||||
or ax, (1 shl BIT_SELECTOR) or (1 shl BIT_10) or (1 shl BIT_10FD) or (1 shl BIT_TX) or (1 shl BIT_TXFD)
|
||||
out dx, ax
|
||||
|
||||
; lock config and BMCR registers
|
||||
|
||||
xor eax, eax
|
||||
set_io REG_9346CR
|
||||
out dx , al
|
||||
out dx, al
|
||||
|
||||
; init RX/TX pointers
|
||||
|
||||
@ -600,7 +601,7 @@ reset:
|
||||
mov [device.curr_tx_desc], al
|
||||
|
||||
; set_io REG_CAPR
|
||||
; out dx , ax
|
||||
; out dx, ax
|
||||
|
||||
; clear packet/byte counters
|
||||
|
||||
@ -611,17 +612,17 @@ reset:
|
||||
; clear missing packet counter
|
||||
|
||||
set_io REG_MPC
|
||||
out dx , eax
|
||||
out dx, eax
|
||||
|
||||
; set RxBuffer address, init RX buffer offset
|
||||
|
||||
mov eax, [device.rx_buffer]
|
||||
mov dword[eax], 0
|
||||
DEBUGF 2,"RX buffer: %x\n", eax
|
||||
DEBUGF 2, "RX buffer: %x\n", eax
|
||||
GetRealAddr
|
||||
DEBUGF 2,"RX buffer: %x\n", eax
|
||||
DEBUGF 2, "RX buffer: %x\n", eax
|
||||
set_io REG_RBSTART
|
||||
out dx , eax
|
||||
out dx, eax
|
||||
|
||||
; Read MAC address
|
||||
|
||||
@ -639,7 +640,7 @@ reset:
|
||||
|
||||
; Indicate that we have successfully reset the card
|
||||
|
||||
DEBUGF 2,"Done!\n"
|
||||
DEBUGF 2, "Done!\n"
|
||||
xor eax, eax
|
||||
|
||||
ret
|
||||
@ -656,9 +657,9 @@ reset:
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
align 4
|
||||
transmit:
|
||||
DEBUGF 1,"\nTransmitting packet, buffer:%x, size:%u\n",[esp+4],[esp+8]
|
||||
DEBUGF 1, "\nTransmitting packet, buffer:%x, size:%u\n", [esp+4], [esp+8]
|
||||
mov eax, [esp+4]
|
||||
DEBUGF 1,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\
|
||||
DEBUGF 1, "To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\
|
||||
[eax+00]:2,[eax+01]:2,[eax+02]:2,[eax+03]:2,[eax+04]:2,[eax+05]:2,\
|
||||
[eax+06]:2,[eax+07]:2,[eax+08]:2,[eax+09]:2,[eax+10]:2,[eax+11]:2,\
|
||||
[eax+13]:2,[eax+12]:2
|
||||
@ -687,7 +688,7 @@ transmit:
|
||||
inc [device.packets_tx]
|
||||
mov eax, [esp+8]
|
||||
add dword [device.bytes_tx], eax
|
||||
adc dword [device.bytes_tx + 4], 0
|
||||
adc dword [device.bytes_tx+4], 0
|
||||
|
||||
; Set the buffer address
|
||||
set_io REG_TSAD0
|
||||
@ -702,12 +703,12 @@ transmit:
|
||||
or eax, (ERTXTH shl BIT_ERTXTH) ; Early threshold
|
||||
out dx, eax
|
||||
|
||||
DEBUGF 1,"Packet Sent!\n"
|
||||
DEBUGF 1, "Packet Sent!\n"
|
||||
xor eax, eax
|
||||
ret 8
|
||||
|
||||
.wait_to_send:
|
||||
DEBUGF 1,"Waiting for timeout\n"
|
||||
DEBUGF 1, "Waiting for timeout\n"
|
||||
|
||||
push edx
|
||||
mov esi, 30
|
||||
@ -725,7 +726,7 @@ transmit:
|
||||
jmp .send_packet
|
||||
|
||||
.fail:
|
||||
DEBUGF 1,"failed!\n"
|
||||
DEBUGF 1, "failed!\n"
|
||||
stdcall KernelFree, [esp+4]
|
||||
or eax, -1
|
||||
ret 8
|
||||
@ -743,7 +744,7 @@ transmit:
|
||||
align 4
|
||||
int_handler:
|
||||
|
||||
DEBUGF 1,"\n%s int\n", my_service
|
||||
DEBUGF 1, "\n%s int\n", my_service
|
||||
|
||||
; find pointer of device wich made IRQ occur
|
||||
|
||||
@ -769,7 +770,7 @@ int_handler:
|
||||
|
||||
.got_it:
|
||||
|
||||
DEBUGF 1,"Device: %x Status: %x ", ebx, ax
|
||||
DEBUGF 1, "Device: %x Status: %x\n", ebx, ax
|
||||
|
||||
;----------------------------------------------------
|
||||
; Received packet ok?
|
||||
@ -785,7 +786,7 @@ int_handler:
|
||||
test al , BUFE ; test if RX buffer is empty
|
||||
jnz .finish ;
|
||||
|
||||
DEBUGF 1,"RX: "
|
||||
DEBUGF 1, "RX: "
|
||||
|
||||
mov eax, [device.rx_buffer]
|
||||
add eax, [device.rx_data_offset]
|
||||
@ -802,7 +803,7 @@ int_handler:
|
||||
adc dword [device.bytes_rx + 4], 0
|
||||
inc dword [device.packets_rx]
|
||||
|
||||
DEBUGF 1,"Received %u bytes\n", ecx
|
||||
DEBUGF 1, "Received %u bytes\n", ecx
|
||||
|
||||
push ebx eax ecx
|
||||
stdcall KernelAlloc, ecx ; Allocate a buffer to put packet into
|
||||
@ -842,12 +843,12 @@ int_handler:
|
||||
and eax, not 3 ; dword alignment
|
||||
|
||||
cmp eax, RX_BUFFER_SIZE
|
||||
jl .no_wrap
|
||||
DEBUGF 2,"Wrapping"
|
||||
jb .no_wrap
|
||||
DEBUGF 2, "Wrapping"
|
||||
sub eax, RX_BUFFER_SIZE
|
||||
.no_wrap:
|
||||
mov [device.rx_data_offset], eax
|
||||
DEBUGF 1,"New RX ptr: %d\n", eax
|
||||
DEBUGF 1, "New RX ptr: %d\n", eax
|
||||
|
||||
set_io 0
|
||||
set_io REG_CAPR ; update 'Current Address of Packet Read register'
|
||||
@ -859,27 +860,27 @@ int_handler:
|
||||
.reset_rx:
|
||||
test byte [eax], (1 shl BIT_CRC)
|
||||
jz .no_crc_error
|
||||
DEBUGF 2,"\nCRC error!\n"
|
||||
DEBUGF 2, "\nCRC error!\n"
|
||||
|
||||
.no_crc_error:
|
||||
test byte [eax], (1 shl BIT_FAE)
|
||||
jz .no_fae_error
|
||||
DEBUGF 1,"\nFrame alignment error!\n"
|
||||
DEBUGF 1, "\nFrame alignment error!\n"
|
||||
|
||||
.no_fae_error:
|
||||
DEBUGF 1,"Reset RX\n"
|
||||
in al , dx ; read command register
|
||||
DEBUGF 1, "Reset RX\n"
|
||||
in al, dx ; read command register
|
||||
push ax
|
||||
|
||||
and al , not (1 shl BIT_RE) ; Clear the RE bit
|
||||
out dx , al
|
||||
and al, not (1 shl BIT_RE) ; Clear the RE bit
|
||||
out dx, al
|
||||
|
||||
pop ax
|
||||
out dx , al ; write original command back
|
||||
out dx, al ; write original command back
|
||||
|
||||
add edx, REG_RXCONFIG - REG_COMMAND ; Restore RX configuration
|
||||
mov ax , RX_CONFIG
|
||||
out dx , ax
|
||||
mov ax, RX_CONFIG
|
||||
out dx, ax
|
||||
|
||||
.finish:
|
||||
pop ax
|
||||
@ -891,8 +892,8 @@ int_handler:
|
||||
jz @f
|
||||
|
||||
push ax
|
||||
xor ecx, ecx
|
||||
.txdesloop:
|
||||
mov ecx, (NUM_TX_DESC-1)*4
|
||||
.txdescloop:
|
||||
set_io 0
|
||||
set_io REG_TSD0
|
||||
add edx, ecx
|
||||
@ -926,16 +927,15 @@ int_handler:
|
||||
;
|
||||
; .nocsl:
|
||||
|
||||
DEBUGF 1,"TX OK: free buffer %x\n", [device.TX_DESC+ecx]:8
|
||||
DEBUGF 1, "TX OK: free buffer %x\n", [device.TX_DESC+ecx]:8
|
||||
push ecx ebx
|
||||
stdcall KernelFree, [device.TX_DESC+ecx]
|
||||
pop ebx ecx
|
||||
mov [device.TX_DESC+ecx], 0
|
||||
|
||||
.notthisone:
|
||||
add ecx, 4
|
||||
cmp ecx, 16
|
||||
jl .txdesloop
|
||||
sub ecx, 4
|
||||
ja .txdescloop
|
||||
pop ax
|
||||
|
||||
;----------------------------------------------------
|
||||
@ -945,12 +945,12 @@ int_handler:
|
||||
jz @f
|
||||
|
||||
push ax
|
||||
DEBUGF 2,"RX-buffer overflow!\n"
|
||||
DEBUGF 2, "RX-buffer overflow!\n"
|
||||
|
||||
set_io 0
|
||||
set_io REG_ISR
|
||||
mov ax , ISR_FIFOOVW or ISR_RXOVW
|
||||
out dx , ax
|
||||
mov ax, ISR_FIFOOVW or ISR_RXOVW
|
||||
out dx, ax
|
||||
pop ax
|
||||
|
||||
;----------------------------------------------------
|
||||
@ -959,7 +959,7 @@ int_handler:
|
||||
test ax, ISR_PUN
|
||||
jz @f
|
||||
|
||||
DEBUGF 2,"Packet underrun!\n"
|
||||
DEBUGF 2, "Packet underrun!\n"
|
||||
|
||||
;----------------------------------------------------
|
||||
; Receive FIFO overflow ?
|
||||
@ -968,12 +968,12 @@ int_handler:
|
||||
jz @f
|
||||
|
||||
push ax
|
||||
DEBUGF 2,"RX fifo overflow!\n"
|
||||
DEBUGF 2, "RX fifo overflow!\n"
|
||||
|
||||
set_io 0
|
||||
set_io REG_ISR
|
||||
mov ax , ISR_FIFOOVW or ISR_RXOVW
|
||||
out dx , ax
|
||||
mov ax, ISR_FIFOOVW or ISR_RXOVW
|
||||
out dx, ax
|
||||
pop ax
|
||||
|
||||
;----------------------------------------------------
|
||||
@ -982,10 +982,11 @@ int_handler:
|
||||
test ax, ISR_LENCHG
|
||||
jz .fail
|
||||
|
||||
DEBUGF 2,"Cable changed!\n"
|
||||
DEBUGF 2, "Cable changed!\n"
|
||||
call cable
|
||||
|
||||
.fail:
|
||||
DEBUGF 2, "\n"
|
||||
ret
|
||||
|
||||
|
||||
@ -999,7 +1000,7 @@ int_handler:
|
||||
|
||||
align 4
|
||||
cable:
|
||||
DEBUGF 1,"Checking Cable status: "
|
||||
DEBUGF 1, "Checking Cable status: "
|
||||
|
||||
mov edx, dword [device.io_addr]
|
||||
add edx, REG_MSR
|
||||
@ -1015,7 +1016,7 @@ cable:
|
||||
and al, 3
|
||||
|
||||
mov byte [device.mode+3], al
|
||||
DEBUGF 1,"Done!\n"
|
||||
DEBUGF 1, "Done!\n"
|
||||
ret
|
||||
|
||||
|
||||
@ -1029,47 +1030,47 @@ ret
|
||||
align 4
|
||||
write_mac: ; in: mac pushed onto stack (as 3 words)
|
||||
|
||||
DEBUGF 2,"Writing MAC: "
|
||||
DEBUGF 2, "Writing MAC: "
|
||||
|
||||
; disable all in command registers
|
||||
|
||||
set_io 0
|
||||
set_io REG_9346CR
|
||||
xor eax, eax
|
||||
out dx , al
|
||||
out dx, al
|
||||
|
||||
set_io REG_IMR
|
||||
xor eax, eax
|
||||
out dx , ax
|
||||
out dx, ax
|
||||
|
||||
set_io REG_ISR
|
||||
mov eax, -1
|
||||
out dx , ax
|
||||
out dx, ax
|
||||
|
||||
; enable writing
|
||||
|
||||
set_io REG_9346CR
|
||||
mov eax, REG_9346CR_WE
|
||||
out dx , al
|
||||
out dx, al
|
||||
|
||||
; write the mac ...
|
||||
|
||||
set_io REG_IDR0
|
||||
pop eax
|
||||
out dx , eax
|
||||
out dx, eax
|
||||
|
||||
set_io REG_IDR0+4
|
||||
xor eax, eax
|
||||
pop ax
|
||||
out dx , eax
|
||||
out dx, eax
|
||||
|
||||
; disable writing
|
||||
|
||||
set_io REG_9346CR
|
||||
xor eax, eax
|
||||
out dx , al
|
||||
out dx, al
|
||||
|
||||
DEBUGF 2,"ok!\n"
|
||||
DEBUGF 2, "ok!\n"
|
||||
|
||||
; Notice this procedure does not ret, but continues to read_mac instead.
|
||||
|
||||
@ -1081,7 +1082,7 @@ write_mac: ; in: mac pushed onto stack (as 3 words)
|
||||
;;;;;;;;;;;;;;;;;;;;;;
|
||||
|
||||
read_mac:
|
||||
DEBUGF 2,"Reading MAC: "
|
||||
DEBUGF 2, "Reading MAC: "
|
||||
|
||||
set_io 0
|
||||
lea edi, [device.mac]
|
||||
@ -1091,7 +1092,7 @@ read_mac:
|
||||
in ax, dx
|
||||
stosw
|
||||
|
||||
DEBUGF 2,"%x-%x-%x-%x-%x-%x\n",[edi-6]:2,[edi-5]:2,[edi-4]:2,[edi-3]:2,[edi-2]:2,[edi-1]:2
|
||||
DEBUGF 2, "%x-%x-%x-%x-%x-%x\n",[edi-6]:2,[edi-5]:2,[edi-4]:2,[edi-3]:2,[edi-2]:2,[edi-1]:2
|
||||
|
||||
ret
|
||||
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2010. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; RTL8169 driver for KolibriOS ;;
|
||||
@ -8,9 +8,7 @@
|
||||
;; Copyright 2007 mike.dld, ;;
|
||||
;; mike.dld@gmail.com ;;
|
||||
;; ;;
|
||||
;; Version 0.1 11 February 2007 ;;
|
||||
;; Version 0.2 3 August 2010 - port to net branch by hidnplayr ;;
|
||||
;; Version 0.3 31 Januari 2011 - bugfixes by hidnplayr ;;
|
||||
;; port to net branch by hidnplayr ;;
|
||||
;; ;;
|
||||
;; References: ;;
|
||||
;; r8169.c - linux driver (etherboot project) ;;
|
||||
@ -414,7 +412,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -427,7 +425,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne .fail
|
||||
|
||||
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
||||
@ -453,7 +451,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
; This device doesnt have its own eth_device structure yet, lets create one
|
||||
.firstdevice:
|
||||
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
|
||||
jge .fail
|
||||
jae .fail
|
||||
|
||||
allocate_and_clear ebx, device_size, .fail ; Allocate memory to put the device structure in
|
||||
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2010. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; DEC 21x4x driver for KolibriOS ;;
|
||||
@ -351,7 +351,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -364,7 +364,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne .fail
|
||||
|
||||
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
||||
@ -390,7 +390,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
; This device doesnt have its own eth_device structure yet, lets create one
|
||||
.firstdevice:
|
||||
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
|
||||
jge .fail
|
||||
jae .fail
|
||||
|
||||
push edx
|
||||
stdcall KernelAlloc, dword device.size ; Allocate the buffer for eth_device structure
|
||||
@ -1085,7 +1085,7 @@ int_handler:
|
||||
; inc free desc
|
||||
inc [device.tx_free_des]
|
||||
cmp [device.tx_free_des], TX_DES_COUNT
|
||||
jle @f
|
||||
jbe @f
|
||||
mov [device.tx_free_des], TX_DES_COUNT
|
||||
@@:
|
||||
|
||||
@ -1239,7 +1239,7 @@ read_mac_eeprom:
|
||||
stosw
|
||||
inc esi
|
||||
cmp esi, 26/2
|
||||
jl .loop
|
||||
jb .loop
|
||||
|
||||
DEBUGF 2,"%x-%x-%x-%x-%x-%x\n",[edi-6]:2,[edi-5]:2,[edi-4]:2,[edi-3]:2,[edi-2]:2,[edi-1]:2
|
||||
|
||||
@ -1297,7 +1297,7 @@ SROM_GetWidth: ; should be 6 or 8 according to some manuals (returns in ecx)
|
||||
|
||||
inc ecx
|
||||
cmp ecx, 12
|
||||
jle .loop2
|
||||
jbe .loop2
|
||||
.end_loop2:
|
||||
|
||||
DEBUGF 1,"Srom width=%u\n", ecx
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2012. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; i8254x driver for KolibriOS ;;
|
||||
@ -166,7 +166,7 @@ MDIC_E = 0x40000000 ; Error
|
||||
ICR_TXDW = 0x00000001 ; TX Desc Written back
|
||||
ICR_TXQE = 0x00000002 ; TX Queue Empty
|
||||
ICR_LSC = 0x00000004 ; Link Status Change
|
||||
ICR_RXSEQ = 0x00000008 ; RX S= ence Error
|
||||
ICR_RXSEQ = 0x00000008 ; RX Sence Error
|
||||
ICR_RXDMT0 = 0x00000010 ; RX Desc min threshold reached
|
||||
ICR_RXO = 0x00000040 ; RX Overrun
|
||||
ICR_RXT0 = 0x00000080 ; RX Timer Interrupt
|
||||
@ -324,7 +324,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -337,7 +337,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne .fail
|
||||
|
||||
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
||||
@ -366,7 +366,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
; This device doesnt have its own eth_device structure yet, lets create one
|
||||
.firstdevice:
|
||||
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
|
||||
jge .fail
|
||||
jae .fail
|
||||
|
||||
allocate_and_clear ebx, sizeof.device_struct, .fail ; Allocate the buffer for device structure
|
||||
|
||||
@ -569,6 +569,10 @@ reset_dontstart:
|
||||
xor eax, eax
|
||||
ret
|
||||
|
||||
align 4
|
||||
reset:
|
||||
call reset_dontstart
|
||||
|
||||
start_i8254x:
|
||||
|
||||
xor eax, eax
|
||||
@ -584,12 +588,6 @@ start_i8254x:
|
||||
xor eax, eax
|
||||
ret
|
||||
|
||||
align 4
|
||||
reset:
|
||||
call reset_dontstart
|
||||
call start_i8254x
|
||||
|
||||
ret
|
||||
|
||||
|
||||
|
||||
@ -652,9 +650,9 @@ transmit:
|
||||
[eax+13]:2,[eax+12]:2
|
||||
|
||||
cmp dword [esp + 8], 1514
|
||||
jg .fail
|
||||
ja .fail
|
||||
cmp dword [esp + 8], 60
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
|
||||
; Program the descriptor (use legacy mode)
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2012. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; i8255x (Intel eepro 100) driver for KolibriOS ;;
|
||||
@ -217,7 +217,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -230,7 +230,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne .fail
|
||||
|
||||
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
||||
@ -594,9 +594,9 @@ transmit:
|
||||
[eax+13]:2,[eax+12]:2
|
||||
|
||||
cmp dword [esp+8], 1500
|
||||
jg .error ; packet is too long
|
||||
ja .error ; packet is too long
|
||||
cmp dword [esp+8], 60
|
||||
jl .error ; packet is too short
|
||||
jb .error ; packet is too short
|
||||
|
||||
set_io 0
|
||||
in ax, dx
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2010. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; MTD80x driver for KolibriOS ;;
|
||||
@ -325,7 +325,7 @@ proc START stdcall, state:dword
|
||||
|
||||
.entry:
|
||||
|
||||
DEBUGF 2,"Loading mtd80x driver\n"
|
||||
DEBUGF 2,"Loading %s driver\n", my_service
|
||||
stdcall RegService, my_service, service_proc
|
||||
ret
|
||||
|
||||
@ -356,7 +356,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -369,7 +369,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne .fail
|
||||
|
||||
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
||||
@ -395,7 +395,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
; This device doesnt have its own eth_device structure yet, lets create one
|
||||
.firstdevice:
|
||||
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
|
||||
jge .fail
|
||||
jae .fail
|
||||
|
||||
allocate_and_clear ebx, device_size, .fail
|
||||
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2010. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; PCnet driver for KolibriOS ;;
|
||||
@ -14,7 +14,7 @@
|
||||
;; ;;
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
|
||||
; $Revision$
|
||||
$Revision$
|
||||
|
||||
format MS COFF
|
||||
|
||||
@ -365,7 +365,7 @@ proc START stdcall, state:dword
|
||||
|
||||
.entry:
|
||||
|
||||
DEBUGF 1,"Loading PCnet driver\n"
|
||||
DEBUGF 1,"Loading %s driver\n", my_service
|
||||
stdcall RegService, my_service, service_proc
|
||||
ret
|
||||
|
||||
@ -396,7 +396,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -409,7 +409,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne .fail
|
||||
|
||||
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
||||
@ -435,7 +435,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
|
||||
.firstdevice:
|
||||
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
|
||||
jge .fail
|
||||
jae .fail
|
||||
|
||||
allocate_and_clear ebx, device_size, .fail
|
||||
|
||||
@ -955,9 +955,9 @@ transmit:
|
||||
[eax+13]:2,[eax+12]:2
|
||||
|
||||
cmp dword [esp+8], 1514
|
||||
jg .nospace ; packet is too long
|
||||
ja .nospace ; packet is too long
|
||||
cmp dword [esp+8], 60
|
||||
jl .nospace ; packet is too short
|
||||
jb .nospace ; packet is too short
|
||||
|
||||
; check descriptor
|
||||
movzx eax, [device.cur_tx]
|
||||
@ -1161,7 +1161,7 @@ write_mac: ; in: mac pushed onto stack (as 3 words)
|
||||
DEBUGF 1,"."
|
||||
inc ecx
|
||||
cmp ecx, PCNET_CSR_PAR2
|
||||
jl @r
|
||||
jb @r
|
||||
|
||||
DEBUGF 1,"\n"
|
||||
|
||||
@ -1185,7 +1185,7 @@ read_mac:
|
||||
push ax
|
||||
DEBUGF 1,"."
|
||||
cmp edx, [device.io_addr]
|
||||
jg @r
|
||||
ja @r
|
||||
|
||||
DEBUGF 1," %x-%x-%x-%x-%x-%x\n",[esp+0]:2,[esp+1]:2,[esp+2]:2,[esp+3]:2,[esp+4]:2,[esp+5]:2
|
||||
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2010-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; rhine.asm ;;
|
||||
@ -584,7 +584,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne @F
|
||||
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
|
||||
@ -597,7 +597,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
jne .fail
|
||||
|
||||
cmp [IOCTL.inp_size], 3 ; Data input must be at least 3 bytes
|
||||
jl .fail
|
||||
jb .fail
|
||||
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given
|
||||
@ -623,7 +623,7 @@ proc service_proc stdcall, ioctl:dword
|
||||
; This device doesnt have its own eth_device structure yet, lets create one
|
||||
.firstdevice:
|
||||
cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card
|
||||
jge .fail
|
||||
jae .fail
|
||||
|
||||
allocate_and_clear ebx, device.size, .fail ; Allocate the buffer for device structure
|
||||
|
||||
|
||||
@ -1,6 +1,6 @@
|
||||
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
|
||||
;; ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2012. All rights reserved. ;;
|
||||
;; Copyright (C) KolibriOS team 2004-2013. All rights reserved. ;;
|
||||
;; Distributed under terms of the GNU General Public License ;;
|
||||
;; ;;
|
||||
;; Ethernet driver for KolibriOS ;;
|
||||
@ -271,7 +271,7 @@ service_proc:
|
||||
; 3. This is SRV_GETVERSION request, no input, 4 bytes output, API_VERSION.
|
||||
; 3a. Output size must be at least 4 bytes.
|
||||
cmp [IOCTL.out_size], 4
|
||||
jl .fail
|
||||
jb .fail
|
||||
; 3b. Write result to the output buffer.
|
||||
mov eax, [IOCTL.output]
|
||||
mov [eax], dword API_VERSION
|
||||
@ -285,7 +285,7 @@ service_proc:
|
||||
; 4a. The driver works only with PCI devices,
|
||||
; so input must be at least 3 bytes long.
|
||||
cmp [IOCTL.inp_size], 3
|
||||
jl .fail
|
||||
jb .fail
|
||||
; 4b. First byte of input is bus type, 1 stands for PCI.
|
||||
mov eax, [IOCTL.input]
|
||||
cmp byte [eax], 1
|
||||
@ -313,7 +313,7 @@ service_proc:
|
||||
.firstdevice:
|
||||
; 4f. Check that we have place for new device.
|
||||
cmp [devices], MAX_DEVICES
|
||||
jge .fail
|
||||
jae .fail
|
||||
; 4g. Allocate memory for device descriptor and receive+transmit buffers.
|
||||
; 4h. Zero the structure.
|
||||
allocate_and_clear ebx, device.size, .fail
|
||||
|
||||
Loading…
Reference in New Issue
Block a user