;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; Copyright (C) KolibriOS team 2004-2021. All rights reserved. ;; ;; Distributed under terms of the GNU General Public License ;; ;; ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; $Revision$ PCI_REG_STATUS_COMMAND = 0x0004 PCI_REG_BAR5 = 0x0024 AHCI_DBGLVL = 0 ; debug output verbosity level. 0 - less verbose, 1 - more verbose ; different SATA device signatures SATA_SIG_ATA = 0x00000101 ; SATA drive SATA_SIG_ATAPI = 0xEB140101 ; SATAPI drive SATA_SIG_SEMB = 0xC33C0101 ; Enclosure management bridge SATA_SIG_PM = 0x96690101 ; Port multiplier ; Device type constants AHCI_DEV_NULL = 0 AHCI_DEV_SATA = 1 AHCI_DEV_SEMB = 2 AHCI_DEV_PM = 3 AHCI_DEV_SATAPI = 4 ; ATA commands ATA_IDENTIFY = 0xEC ATA_CMD_READ_DMA_EX = 0x25 ATA_CMD_WRITE_DMA_EX = 0x35 ; ATA constants ATA_DEV_BUSY = 0x80 ATA_DEV_DRQ = 0x08 ; ATAPI commands ATAPI_IDENTIFY = 0xA1 PRDT_MAX_ENTRIES = 16 ;65535 ; bit_ prefix means that its index of bit ; format: bit_AHCI_STR_REG_BIT bit_AHCI_HBA_CAP2_BOH = 0 ; Supports BIOS/OS Handoff bit_AHCI_HBA_BOHC_BOS = 0 ; BIOS-Owned Semaphore (BIOS owns controller) bit_AHCI_HBA_BOHC_OOS = 1 ; OS-Owned Semaphore (OS owns controller) bit_AHCI_HBA_BOHC_BB = 4 ; BIOS Busy (polling bit while BIOS cleans up bit_AHCI_HBA_GHC_AHCI_ENABLE = 31 ; Enable AHCI mode bit_AHCI_HBA_GHC_RESET = 0 ; Reset HBA bit_AHCI_HBA_GHC_INTERRUPT_ENABLE = 1 ; Enable interrupts from the HBA bit_AHCI_HBA_PxCMD_ST = 0 bit_AHCI_HBA_PxCMD_FRE = 4 bit_AHCI_HBA_PxCMD_FR = 14 bit_AHCI_HBA_PxCMD_CR = 15 bit_AHCI_HBA_PxIS_TFES = 30 AHCI_HBA_PxCMD_ST = 1 shl 0 AHCI_HBA_PxCMD_FRE = 1 shl 4 AHCI_HBA_PxCMD_FR = 1 shl 14 AHCI_HBA_PxCMD_CR = 1 shl 15 bit_AHCI_H2D_FLAG_CMD = 7 AHCI_HBA_PxSSTS_DET = 0xF AHCI_HBA_PORT_IPM_ACTIVE = 1 AHCI_HBA_PxSSTS_DET_PRESENT = 3 AHCI_MAX_PORTS = 32 ; ;HBA_MEMORY_SIZE = 0x1100 AHCI_PORT_TIMEOUT = 1000000 ; Frame Information Structure Types FIS_TYPE_REG_H2D = 0x27 ; Register FIS - host to device FIS_TYPE_REG_D2H = 0x34 ; Register FIS - device to host FIS_TYPE_DMA_ACT = 0x39 ; DMA activate FIS - device to host FIS_TYPE_DMA_SETUP = 0x41 ; DMA setup FIS - bidirectional FIS_TYPE_DATA = 0x46 ; Data FIS - bidirectional FIS_TYPE_BIST = 0x58 ; BIST activate FIS - bidirectional FIS_TYPE_PIO_SETUP = 0x5F ; PIO setup FIS - device to host FIS_TYPE_DEV_BITS = 0xA1 ; Set device bits FIS - device to host struct AHCI_DATA abar dd ? ; pointer to HBA Memory (BAR5) mapped to virtual kernelspace memory pcidev dd ? ; pointer to corresponding PCIDEV structure ends ; Generic Host Control registers struct HBA_MEM cap dd ? ; 0x00, Host capabilities ghc dd ? ; 0x04, Global host control is dd ? ; 0x08, Interrupt status pi dd ? ; 0x0C, Port implemented version dd ? ; 0x10, Version ccc_ctl dd ? ; 0x14, Command completion coalescing control ccc_pts dd ? ; 0x18, Command completion coalescing ports em_loc dd ? ; 0x1C, Enclosure management location em_ctl dd ? ; 0x20, Enclosure management control cap2 dd ? ; 0x24, Host capabilities extended bohc dd ? ; 0x28, BIOS/OS handoff control and status reserved rb (0xA0-HBA_MEM.reserved) ; 0x2C - 0x9F, Reserved vendor rb (0x100-HBA_MEM.vendor) ; 0xA0 - 0xFF, Vendor specific ports rb (sizeof.HBA_PORT*AHCI_MAX_PORTS) ; 0x100 - 0x10FF, Port control registers, max AHCI_MAX_PORTS ends ; Port Control registers struct HBA_PORT command_list_base_l dd ? ; 0x00, command list base address, 1K-byte aligned command_list_base_h dd ? ; 0x04, command list base address upper 32 bits, used on 64 bit systems fis_base_l dd ? ; 0x08, FIS base address, 256-byte aligned fis_base_h dd ? ; 0x0C, FIS base address upper 32 bits, used on 64 bit systems interrupt_status dd ? ; 0x10 interrupt_enable dd ? ; 0x14 command dd ? ; 0x18, command and status reserved0 dd ? ; 0x1C task_file_data dd ? ; 0x20 signature dd ? ; 0x24 sata_status dd ? ; 0x28, SATA status (SCR0:SStatus) sata_control dd ? ; 0x2C, SATA control (SCR2:SControl) sata_error dd ? ; 0x30, SATA error (SCR1:SError) sata_active dd ? ; 0x34, SATA active (SCR3:SActive) command_issue dd ? ; 0x38 sata_notification dd ? ; 0x3C, SATA notification (SCR4:SNotification) fis_based_switch_control dd ? ; 0x40 reserved1 rd 11 ; 0x44 - 0x6F vendor rd 4 ; 0x70 - 0x7F, vendor specific ends ; Command header structure, size = 32 bytes struct HBA_CMD_HDR flags1 db ? ; 0bPWACCCCC, P - Prefetchable, W - Write (1: H2D, 0: D2H) ; A - ATAPI, C - Command FIS length in DWORDS, 2 ~ 16 flags2 db ? ; 0bPPPPRCB(Re), P - Port multiplier port, R - Reserved, ; C - Clear busy upon R_OK, B - BIST, Re - Reset prdtl dw ? ; Physical region descriptor table length in entries prdbc dd ? ; Physical region descriptor byte count transferred ctba dd ? ; Command table descriptor base address ctbau dd ? ; Command table descriptor base address upper 32 bits rd 4 ; Reserved ends ; Physical region descriptor table entry, size = 16 bytes struct HBA_PRDT_ENTRY dba dd ? ; Data base address dbau dd ? ; Data base address upper 32 bits dd ? ; Reserved flags dd ? ; 0bIR..RD..D, I (1 bit) - Interrupt on completion, ; R (9 bits) - Reserved, D (22 bits) - Byte count, 4M max ends struct HBA_CMD_TBL cfis rb 64 ; 0x00, Command FIS acmd rb 16 ; 0x40, ATAPI command, 12 or 16 bytes rb 48 ; 0x50, Reserved prdt_entry HBA_PRDT_ENTRY ; 0x80, Physical region descriptor table entries, 0 ~ 65535 ; so, this structure is variable-length ends ; Contains virtual mappings for port phys memory regions struct PORT_DATA clb dd ? ; Command list base fb dd ? ; FIS base ctba_arr rd 32 ; ctba_arr[0] = clb[0].ctba, ... and so on. port dd ? ; address of correspoding HBA_PORT structure portno dd ? ; port index, 0..31 drive_type db ? ; drive type sector_count dq ? ; number of sectors ends ; Register FIS – Host to Device struct FIS_REG_H2D fis_type db ? ; FIS_TYPE_REG_H2D flags db ? ; 0bCRRRPPPP, C - 1: Command, 0: Control ; R - Reserved, P - Port multiplier command db ? ; Command register featurel db ? ; Feature register, 7:0 lba0 db ? ; LBA low register, 7:0 lba1 db ? ; LBA mid register, 15:8 lba2 db ? ; LBA high register, 23:16 device db ? ; Device register lba3 db ? ; LBA register, 31:24 lba4 db ? ; LBA register, 39:32 lba5 db ? ; LBA register, 47:40 featureh db ? ; Feature register, 15:8 countl db ? ; Count register, 7:0 counth db ? ; Count register, 15:8 icc db ? ; Isochronous command completion control db ? ; Control register rb 4 ; Reserved ends ; Register FIS – Device to Host struct FIS_REG_D2H fis_type db ? ; FIS_TYPE_REG_D2H flags db ? ; 0bRIRPPPP, P - Port multiplier, R - Reserved ; I - Interrupt bit status db ? ; Status register error db ? ; Error register lba0 db ? ; LBA low register, 7:0 lba1 db ? ; LBA mid register, 15:8 lba2 db ? ; LBA high register, 23:16 device db ? ; Device register lba3 db ? ; LBA register, 31:24 lba4 db ? ; LBA register, 39:32 lba5 db ? ; LBA register, 47:40 db ? ; Reserved countl db ? ; Count register, 7:0 counth db ? ; Count register, 15:8 rb 2 ; Reserved rb 4 ; Reserved ends ; Data FIS – Bidirectional struct FIS_DATA fis_type db ? ; FIS_TYPE_DATA flags db ? ; 0bRRRRPPPP, R - Reserved, P - Port multiplier rb 2 ; Reserved ; DWORD 1 ~ N (?) data rd 1 ; Payload ends ; PIO Setup – Device to Host struct FIS_PIO_SETUP fis_type db ? ; FIS_TYPE_PIO_SETUP flags db ? ; 0bRIDRPPPP, P - Port multiplier, R - Reserved ; I - Interrupt bit, D - Data transfer direction, 1 - device to host status db ? ; Status register error db ? ; Error register lba0 db ? ; LBA low register, 7:0 lba1 db ? ; LBA mid register, 15:8 lba2 db ? ; LBA high register, 23:16 device db ? ; Device register lba3 db ? ; LBA register, 31:24 lba4 db ? ; LBA register, 39:32 lba5 db ? ; LBA register, 47:40 db ? ; Reserved countl db ? ; Count register, 7:0 counth db ? ; Count register, 15:8 db ? ; Reserved e_status db ? ; New value of status register tc dw ? ; Transfer count rb 2 ; Reserved ends ; DMA Setup – Device to Host struct FIS_DMA_SETUP fis_type db ? ; FIS_TYPE_DMA_SETUP flags db ? ; 0bAIDRPPPP, A - Auto-activate. Specifies if DMA Activate FIS is needed, ; I - Interrupt bit, D - Data transfer direction, 1 - device to host, ; R - Reserved, P - Port multiplier rb 2 ; Reserved DMAbufferID dq ? ; DMA Buffer Identifier. ; Used to Identify DMA buffer in host memory. ; SATA Spec says host specific and not in Spec. ; Trying AHCI spec might work. dd ? ; Reserved DMAbufOffset dd ? ; Byte offset into buffer. First 2 bits must be 0 TransferCount dd ? ; Number of bytes to transfer. Bit 0 must be 0 dd ? ; Reserved ends ; Set device bits FIS - device to host struct FIS_DEV_BITS fis_type db ? ; FIS_TYPE_DEV_BITS flags db ? ; 0bNIRRPPPP, N - Notification, I - Interrupt, ; R - Reserved, P - Port multiplier status db ? ; Status register error db ? ; Error register protocol dd ? ; Protocol ends struct HBA_FIS dsfis FIS_DMA_SETUP ; 0x00, DMA Setup FIS rb 4 ; padding psfis FIS_PIO_SETUP ; 0x20, PIO Setup FIS rb 12 ; padding rfis FIS_REG_D2H ; 0x40, Register - Device to Host FIS rb 4 ; padding sdbfis FIS_DEV_BITS ; 0x58, Set Device Bit FIS ufis rb 64 ; 0x60 rb (0x100 - 0xA0) ; 0xA0, Reserved ends ; -------------------------------------------------- uglobal align 4 struct SD_DATA ahci_controller AHCI_DATA port_data_arr rb (sizeof.PORT_DATA*AHCI_MAX_PORTS) ahci_mutex MUTEX ends sd1_data SD_DATA sd2_data SD_DATA sd3_data SD_DATA sd4_data SD_DATA sd5_data SD_DATA sd6_data SD_DATA sd7_data SD_DATA sd8_data SD_DATA sd_data dd ? endg iglobal align 4 ahci_callbacks: dd ahci_callbacks.end - ahci_callbacks dd 0 ; no close function dd 0 ; no closemedia function dd ahci_querymedia dd ahci_read dd ahci_write dd 0 ; no flush function dd 0 ; use default cache size .end: hd_name db 'sd', 0, 0, 0 sd_counter dd 0 controllers_counter dd 0 endg ; ----------------------------------------------------------------------- ; detect ahci controller and initialize align 4 ahci_init: mov ecx, sd1_data.ahci_controller mov esi, pcidev_list mov [sd_data], sd1_data mov [sd_counter], 0 .find_ahci_ctr: mov esi, [esi + PCIDEV.fd] cmp esi, pcidev_list jz .ahci_ctr_not_found mov eax, [esi + PCIDEV.class] ;DEBUGF 1, "K: device class = %x\n", eax shr eax, 8 ; shift right because lowest 8 bits if ProgIf field cmp eax, 0x0106 ; 0x01 - Mass Storage Controller class, 0x06 - Serial ATA Controller subclass jz .ahci_ctr_found jmp .find_ahci_ctr .ahci_ctr_not_found: DEBUGF 1, "K: AHCI controller not found\n" ret .ahci_ctr_found: push esi mov ecx, [sd_data] add ecx, SD_DATA.ahci_mutex call mutex_init mov ecx, [sd_data] add ecx, SD_DATA.ahci_controller mov [ecx + AHCI_DATA.pcidev], esi mov eax, [esi+PCIDEV.class] movzx ebx, byte [esi+PCIDEV.bus] movzx ecx, byte [esi+PCIDEV.devfn] shr ecx, 3 ; get rid of 3 lowest bits (function code), the rest bits is device code movzx edx, byte [esi+PCIDEV.devfn] and edx, 00000111b ; get only 3 lowest bits (function code) DEBUGF 1, "K: found AHCI controller, (class, subcl, progif) = %x, bus = %x, device = %x, function = %x\n", eax, ebx, ecx, edx ; get BAR5 value, it is physical address movzx ebx, [esi + PCIDEV.bus] movzx ebp, [esi + PCIDEV.devfn] stdcall pci_read32, ebx, ebp, PCI_REG_BAR5 DEBUGF 1, "K: AHCI controller MMIO = %x\n", eax mov edi, eax ; get the size of MMIO region stdcall pci_write32, ebx, ebp, PCI_REG_BAR5, 0xFFFFFFFF stdcall pci_read32, ebx, ebp, PCI_REG_BAR5 not eax inc eax DEBUGF 1, "K: AHCI: MMIO region size = 0x%x bytes\n", eax ; Map MMIO region to virtual memory stdcall map_io_mem, edi, eax, PG_SWR + PG_NOCACHE push ecx mov ecx, [sd_data] add ecx, SD_DATA.ahci_controller mov [ecx + AHCI_DATA.abar], eax pop ecx DEBUGF 1, "K: AHCI controller BAR5 mapped to virtual addr %x\n", eax ; Restore the original BAR5 value stdcall pci_write32, ebx, ebp, PCI_REG_BAR5, edi ; Enable dma bus mastering, memory space access, clear the "disable interrupts" bit ; Usually, it is already done before us movzx ebx, [esi + PCIDEV.bus] movzx ebp, [esi + PCIDEV.devfn] stdcall pci_read32, ebx, ebp, PCI_REG_STATUS_COMMAND DEBUGF 1, "K: AHCI: pci_status_command = %x\nEnabling interrupts, DMA bus mastering and memory space access\n", eax or eax, 0x06 ; pci.command |= 0x06 (dma bus mastering + memory space access) btr eax, 10 ; clear the "disable interrupts" bit DEBUGF 1, "K: AHCI: pci_status_command = %x\n", eax stdcall pci_write32, ebx, ebp, PCI_REG_STATUS_COMMAND, eax ; ; Print some register values to debug board ; mov esi, [[sd_data].ahci_controller + AHCI_DATA.abar] ; DEBUGF 1, "K: AHCI: HBA.cap = %x, HBA.ghc = %x, HBA_MEM.version = %x\n", [esi + HBA_MEM.cap], [esi + HBA_MEM.ghc], [esi + HBA_MEM.version] ;------------------------------------------------------- ; Request BIOS/OS ownership handoff, if supported. (TODO check correctness) push ecx mov ecx, [sd_data] add ecx, SD_DATA.ahci_controller mov esi, [ecx + AHCI_DATA.abar] pop ecx ;mov ebx, [esi + HBA_MEM.cap2] ;DEBUGF 1, "K: AHCI: HBA_MEM.cap2 = %x\n", ebx bt [esi + HBA_MEM.cap2], bit_AHCI_HBA_CAP2_BOH jnc .end_handoff DEBUGF 1, "K: AHCI: requesting AHCI ownership change...\n" bts [esi + HBA_MEM.bohc], bit_AHCI_HBA_BOHC_OOS .wait_not_bos: bt [esi + HBA_MEM.bohc], bit_AHCI_HBA_BOHC_BOS jc .wait_not_bos mov ebx, 3 call delay_hs ; if Bios Busy is still set after 30 mS, wait 2 seconds. bt [esi + HBA_MEM.bohc], bit_AHCI_HBA_BOHC_BB jnc @f mov ebx, 200 call delay_hs @@: DEBUGF 1, "K: AHCI: ownership change completed.\n" .end_handoff: ;------------------------------------------------------- ; enable the AHCI and reset it bts [esi + HBA_MEM.ghc], bit_AHCI_HBA_GHC_AHCI_ENABLE bts [esi + HBA_MEM.ghc], bit_AHCI_HBA_GHC_RESET ; wait for reset to complete .wait_reset: bt [esi + HBA_MEM.ghc], bit_AHCI_HBA_GHC_RESET jc .wait_reset ; enable the AHCI and interrupts bts [esi + HBA_MEM.ghc], bit_AHCI_HBA_GHC_AHCI_ENABLE bts [esi + HBA_MEM.ghc], bit_AHCI_HBA_GHC_INTERRUPT_ENABLE mov ebx, 2 call delay_hs DEBUGF 1, "K: AHCI: caps: %x %x, ver: %x, ghc: %x, pi: %x\n", [esi + HBA_MEM.cap], [esi + HBA_MEM.cap2], [esi + HBA_MEM.version], [esi + HBA_MEM.ghc], [esi + HBA_MEM.pi] ; TODO: ; calculate irq line ; ahciHBA->ghc |= AHCI_GHC_IE; ; IDT::RegisterInterruptHandler(irq, InterruptHandler); ; ahciHBA->is = 0xffffffff; xor ebx, ebx .detect_drives: cmp ebx, AHCI_MAX_PORTS jae .end_detect_drives ; if port with index ebx is not implemented then go to next mov ecx, [esi + HBA_MEM.pi] bt ecx, ebx jnc .continue_detect_drives mov edi, ebx imul edi, sizeof.HBA_PORT add edi, HBA_MEM.ports add edi, esi ; now edi - base of HBA_MEM.ports[ebx] DEBUGF 1, "K: AHCI: port %d, cmd = %x, ssts = %x\n", ebx, [edi + HBA_PORT.command], [edi + HBA_PORT.sata_status] ; If port is not idle force it to be idle mov eax, [edi + HBA_PORT.command] and eax, (AHCI_HBA_PxCMD_ST or AHCI_HBA_PxCMD_CR or AHCI_HBA_PxCMD_FRE or AHCI_HBA_PxCMD_FR) test eax, eax jz @f mov eax, edi DEBUGF 1, "ahci_stop_cmd..\n" call ahci_stop_cmd @@: ; TODO: what is purpose of this block of code ? ; Reset port, disable slumber and partial state ; mov [edi + HBA_PORT.sata_control], 0x301 ; push ebx ; mov ebx, 5 ; wait 50 ms ; call delay_hs ; pop ebx ; mov [edi + HBA_PORT.sata_control], 0x300 ; if(abar->cap & HBA_MEM_CAP_SSS) ; { ; abar->ports[i].cmd |= (HBA_PxCMD_SUD | HBA_PxCMD_POD | HBA_PxCMD_ICC); ; Sleep(10); ; } ; rewritten to: bt [esi + HBA_MEM.cap], 27 ; check Supports Staggered Spin-up bit in capabilities jnc @f DEBUGF 1, "Supports Staggered Spin-up, spinning up the port..\n" or [edi + HBA_PORT.command], (0x0002 or 0x0004 or 0x10000000) push ebx mov ebx, 10 ; wait 100 ms call delay_hs pop ebx @@: ; Clear interrupt status and error status mov [edi + HBA_PORT.sata_error], 0xFFFFFFFF mov [edi + HBA_PORT.interrupt_status], 0xFFFFFFFF ; ------------------------------------------ mov ecx, [edi + HBA_PORT.sata_status] shr ecx, 8 and ecx, 0x0F cmp ecx, AHCI_HBA_PORT_IPM_ACTIVE jne .continue_detect_drives mov ecx, [edi + HBA_PORT.sata_status] and ecx, AHCI_HBA_PxSSTS_DET cmp ecx, AHCI_HBA_PxSSTS_DET_PRESENT jne .continue_detect_drives ; DEBUGF 1, "K: AHCI: found drive at port %d, cmd = 0x%x, ssts = 0x%x, signature = 0x%x\n", ebx, [edi + HBA_PORT.command], [edi + HBA_PORT.sata_status], [edi + HBA_PORT.signature] mov ecx, ebx imul ecx, sizeof.PORT_DATA mov ecx, [sd_data] add ecx, SD_DATA.port_data_arr stdcall ahci_port_rebase, edi, ebx, ecx ; DEBUGF 1, "K: AHCI: After REBASING, signature = 0x%x\n", [edi + HBA_PORT.signature] ; Determine drive type by checking port signature .switch_sig: cmp [edi + HBA_PORT.signature], SATA_SIG_ATA mov eax, AHCI_DEV_SATA jz .end_switch_sig cmp [edi + HBA_PORT.signature], SATA_SIG_ATAPI mov eax, AHCI_DEV_SATAPI jz .end_switch_sig cmp [edi + HBA_PORT.signature], SATA_SIG_SEMB mov eax, AHCI_DEV_SEMB jz .end_switch_sig cmp [edi + HBA_PORT.signature], SATA_SIG_PM mov eax, AHCI_DEV_PM jz .end_switch_sig DEBUGF 1, "Unknown device signature\n" mov eax, AHCI_DEV_NULL .end_switch_sig: mov [ecx + PORT_DATA.drive_type], al DEBUGF 1, "K: AHCI: found drive on port %u: TYPE = %u\n", ebx, [ecx + PORT_DATA.drive_type] stdcall ahci_port_identify, ecx cmp [ecx + PORT_DATA.drive_type], AHCI_DEV_SATA jne .after_add_disk ; skip adding disk code ; register disk in system: ;stdcall ahci_read_first_sector, ecx push ecx mov eax, [sd_counter] inc [sd_counter] xor edx, edx mov ecx, 10 div ecx ; eax = sd_counter / 10, edx = sd_counter % 10 test eax, eax jz .concat_one add al, '0' mov byte [hd_name + 2], al add dl, '0' mov byte [hd_name + 3], dl jmp .endif1 .concat_one: add dl, '0' mov byte [hd_name + 2], dl .endif1: pop ecx DEBUGF 1, "adding '%s'\n", hd_name push ecx stdcall disk_add, ahci_callbacks, hd_name, ecx, 0 pop ecx test eax, eax jz .disk_add_fail push ecx stdcall disk_media_changed, eax, 1 ; system will scan for partitions on disk pop ecx jmp .after_add_disk .disk_add_fail: DEBUGF 1, "Failed to add disk\n" .after_add_disk: .continue_detect_drives: inc ebx jmp .detect_drives .end_detect_drives: pop esi add [sd_data], sizeof.SD_DATA inc [controllers_counter] cmp [controllers_counter], 8 jnz .find_ahci_ctr DEBUGF 1, "AHCI: reached controllers number limit\n" ret ; ------------------------------------------------- modelstr rb 42 ; Identify drive on port ; TODO check ; in: pdata - address of PORT_DATA structure proc ahci_port_identify stdcall, pdata: dword locals cmdslot dd ? cmdheader dd ? cmdtable dd ? buf_phys dd ? buf_virt dd ? endl pushad mov esi, [pdata] ; esi - address of PORT_DATA struct of port mov edi, [esi + PORT_DATA.port] ; edi - address of HBA_PORT struct of port mov eax, edi call ahci_find_cmdslot cmp eax, -1 jne .cmdslot_found DEBUGF 1, "No free cmdslot on port %u\n", [esi + PORT_DATA.portno] jmp .ret .cmdslot_found: mov [cmdslot], eax ; DEBUGF 1, "Found free cmdslot %u on port %u\n", [cmdslot], [esi + PORT_DATA.portno] shl eax, BSF sizeof.HBA_CMD_HDR add eax, [esi + PORT_DATA.clb] mov [cmdheader], eax ; address of virtual mapping of command header mov eax, [cmdslot] mov eax, [esi + eax*4 + PORT_DATA.ctba_arr] mov [cmdtable], eax ; address of virtual mapping of command table of command header stdcall _memset, eax, 0, sizeof.HBA_CMD_TBL call alloc_page mov [buf_phys], eax stdcall map_io_mem, eax, 4096, PG_NOCACHE + PG_SWR ; map to virt memory so we can work with it mov [buf_virt], eax mov eax, [cmdtable] mov ebx, [buf_phys] mov dword [eax + HBA_CMD_TBL.prdt_entry + HBA_PRDT_ENTRY.dba], ebx mov dword [eax + HBA_CMD_TBL.prdt_entry + HBA_PRDT_ENTRY.dbau], 0 and [eax + HBA_CMD_TBL.prdt_entry + HBA_PRDT_ENTRY.flags], not 0x3FFFFF ; zero out lower 22 bits, they used for byte count or [eax + HBA_CMD_TBL.prdt_entry + HBA_PRDT_ENTRY.flags], 512 - 1 ; reason why -1 see in spec on this field ; or [eax + HBA_CMD_TBL.prdt_entry + HBA_PRDT_ENTRY.flags], 1 shl 31 ; enable interrupt on completion mov eax, [cmdheader] and [eax + HBA_CMD_HDR.flags1], not 0x1F ; zero out lower 5 bits, they will be used for cfl or [eax + HBA_CMD_HDR.flags1], (sizeof.FIS_REG_H2D / 4) ; set command fis length in dwords movzx bx, [eax + HBA_CMD_HDR.flags1] btr bx, 6 ; flag W = 0 mov [eax + HBA_CMD_HDR.flags1], bl movzx bx, [eax + HBA_CMD_HDR.flags2] btr bx, 2 ; flag C = 0 mov [eax + HBA_CMD_HDR.flags2], bl mov [eax + HBA_CMD_HDR.prdtl], 1 mov eax, [cmdtable] mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.fis_type], FIS_TYPE_REG_H2D movzx ebx, byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.flags] bts ebx, bit_AHCI_H2D_FLAG_CMD ; Set Command bit in H2D FIS. mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.flags], bl mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.command], ATA_IDENTIFY cmp [esi + PORT_DATA.drive_type], AHCI_DEV_SATAPI jne @f mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.command], ATAPI_IDENTIFY @@: mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.device], 0 ; Wait on previous command to complete, before issuing new command. stdcall ahci_port_wait, edi, AHCI_PORT_TIMEOUT ; DEBUGF 1, "eax = %x\n", eax ; TODO check eax error value mov eax, [cmdslot] bts [edi + HBA_PORT.command_issue], eax ; Issue the command ; Wait for command completion stdcall ahci_port_cmd_wait, edi, eax;, AHCI_PORT_CMD_TIMEOUT ; DEBUGF 1, " eax = %x\n", eax ; TODO check eax error value ; DEBUGF 1, "sata_error register = 0x%x\n", [edi + HBA_PORT.sata_error] mov esi, [buf_virt] add esi, 27*2 mov edi, modelstr mov ecx, ((46-27)+1)*2 cld rep movsb mov byte [edi], 0 stdcall swap_bytes_in_words, modelstr, (46-27)+1 DEBUGF 1, "IDENTIFICATION RESULT: MODEL = %s\n", modelstr mov esi, [buf_virt] mov eax, [esi + 200] mov edx, [esi + 200 + 4] DEBUGF 1, "lba48 mode sector count = 0x%x:%x\n", edx, eax mov ebx, [pdata] mov dword [ebx + PORT_DATA.sector_count], eax mov dword [ebx + PORT_DATA.sector_count + 4], edx shrd eax, edx, 11 ; i.e *512 / 1024 / 1024, 512 - sector size DEBUGF 1, "disk capacity = %u MiB ", eax shrd eax, edx, 10 ; / 1024 DEBUGF 1, "= %u GiB\n", eax .ret: popad ret endp proc ahci_querymedia stdcall, pdata, mediainfo push ecx edx mov eax, [mediainfo] mov edx, [pdata] mov [eax + DISKMEDIAINFO.Flags], 0 mov [eax + DISKMEDIAINFO.SectorSize], 512 mov ecx, dword[edx + PORT_DATA.sector_count] mov dword [eax + DISKMEDIAINFO.Capacity], ecx mov ecx, dword[edx + PORT_DATA.sector_count + 4] mov dword [eax + DISKMEDIAINFO.Capacity + 4], ecx pop edx ecx xor eax, eax ret endp ; Read/write sectors ; return value: 0 = success, otherwise = error proc ahci_rw_sectors stdcall pdata: dword, vbuf: dword, startsector: qword, numsectors: dword, is_write: dword locals cmdslot dd ? cmdheader dd ? cmdtable dd ? vbuf_orig dd ? vbuf_len dd ? phys_region_start dd ? new_phys_region_start dd ? cur_prd dd ? cur_phys dd ? dbc dd ? cur_phys_page dd ? next_phys_page dd ? cur_antioffset dd ? prdt_bytes_total dd ? endl pushad DEBUGF AHCI_DBGLVL, " ahci_rw_sectors: buffer = 0x%x, startsector = 0x%x:%x, numsectors = %u, is_write = %u\n", [vbuf], [startsector], [startsector + 4], [numsectors], [is_write]:1 mov esi, [pdata] ; esi - address of PORT_DATA struct of port mov edi, [esi + PORT_DATA.port] ; edi - address of HBA_PORT struct of port mov eax, edi call ahci_find_cmdslot cmp eax, -1 jne .cmdslot_found DEBUGF AHCI_DBGLVL, "No free cmdslot on port %u\n", [esi + PORT_DATA.portno] jmp .fail .cmdslot_found: mov [cmdslot], eax DEBUGF AHCI_DBGLVL, "Found free cmdslot %u on port %u\n", [cmdslot], [esi + PORT_DATA.portno] shl eax, BSF sizeof.HBA_CMD_HDR add eax, [esi + PORT_DATA.clb] mov [cmdheader], eax ; address of virtual mapping of command header mov eax, [cmdslot] mov eax, [esi + eax*4 + PORT_DATA.ctba_arr] mov [cmdtable], eax ; address of virtual mapping of command table of command header mov eax, [cmdheader] and [eax + HBA_CMD_HDR.flags1], not 0x1F ; zero out lower 5 bits, they will be used for cfl or [eax + HBA_CMD_HDR.flags1], (sizeof.FIS_REG_H2D / 4) ; set command fis length in dwords movzx bx, [eax + HBA_CMD_HDR.flags1] btr bx, 6 ; flag W = 0 cmp [is_write], 1 ; if is_write then set W flag jne @f bts bx, 6 @@: mov [eax + HBA_CMD_HDR.flags1], bl movzx bx, [eax + HBA_CMD_HDR.flags2] btr bx, 2 ; flag C = 0 mov [eax + HBA_CMD_HDR.flags2], bl mov eax, [vbuf] mov [vbuf_orig], eax mov ebx, [numsectors] shl ebx, 9 ; *= 512 mov [vbuf_len], ebx DEBUGF AHCI_DBGLVL, "vbuf_len = %u bytes\n", ebx mov ebx, [vbuf] and ebx, 0xFFF mov eax, [vbuf] call get_pg_addr add eax, ebx mov [phys_region_start], eax mov [prdt_bytes_total], 0 mov [cur_prd], 0 .fill_prdt: cmp [vbuf_len], 0 jbe .fill_prdt_end mov eax, [vbuf] call get_pg_addr mov [cur_phys_page], eax mov eax, [vbuf] add eax, 4096 call get_pg_addr mov [next_phys_page], eax mov eax, 4096 mov ebx, [vbuf] and ebx, 0xFFF sub eax, ebx mov [cur_antioffset], eax mov eax, [cur_phys_page] add eax, ebx mov [cur_phys], eax .check_if1: mov eax, [vbuf_len] cmp eax, [cur_antioffset] ja .check_if2 mov eax, [cur_phys] sub eax, [phys_region_start] add eax, [vbuf_len] dec eax mov [dbc], eax mov eax, [next_phys_page] mov [new_phys_region_start], eax jmp .add_prd .check_if2: mov eax, [cur_phys] add eax, [cur_antioffset] cmp eax, [next_phys_page] je .check_if3 mov eax, [cur_phys] add eax, [cur_antioffset] sub eax, [phys_region_start] dec eax mov [dbc], eax mov eax, [next_phys_page] mov [new_phys_region_start], eax jmp .add_prd .check_if3: mov eax, [cur_phys] add eax, [cur_antioffset] sub eax, [phys_region_start] cmp eax, 4*1024*1024 jb .after_ifs mov [dbc], 4*1024*1024 - 1 mov eax, [phys_region_start] add eax, 4*1024*1024 jmp .add_prd .after_ifs: jmp .step_next .add_prd: mov ebx, [cur_prd] shl ebx, BSF sizeof.HBA_PRDT_ENTRY add ebx, [cmdtable] add ebx, HBA_CMD_TBL.prdt_entry ; now ebx - address of 'th prdt_entry DEBUGF AHCI_DBGLVL, "Added PRDT entry: dba = 0x%x, dbc = %u\n", [phys_region_start], [dbc] mov eax, [phys_region_start] mov [ebx + HBA_PRDT_ENTRY.dba], eax mov [ebx + HBA_PRDT_ENTRY.dbau], 0 and [ebx + HBA_PRDT_ENTRY.flags], not 0x3FFFFF ; zero out lower 22 bits, they used for byte count mov eax, [dbc] or [ebx + HBA_PRDT_ENTRY.flags], eax inc [cur_prd] mov eax, [dbc] inc eax add [prdt_bytes_total], eax mov eax, [new_phys_region_start] mov [phys_region_start], eax cmp [cur_prd], PRDT_MAX_ENTRIES jne @f jmp .fill_prdt_end @@: .step_next: mov eax, [vbuf_len] cmp eax, [cur_antioffset] jbe @f mov eax, [cur_antioffset] @@: add [vbuf], eax sub [vbuf_len], eax jmp .fill_prdt .fill_prdt_end: mov eax, [cmdheader] mov ebx, [cur_prd] DEBUGF AHCI_DBGLVL, " PRDTL = %u\n", ebx mov [eax + HBA_CMD_HDR.prdtl], bx mov eax, [prdt_bytes_total] DEBUGF AHCI_DBGLVL, " prdt_bytes_total = %u\n", eax shr eax, 9 ; /= 512 mov [numsectors], eax mov eax, [cmdtable] mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.fis_type], FIS_TYPE_REG_H2D movzx ebx, byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.flags] bts ebx, bit_AHCI_H2D_FLAG_CMD ; Set Command bit in H2D FIS. mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.flags], bl mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.command], ATA_CMD_READ_DMA_EX cmp [is_write], 1 jne @f mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.command], ATA_CMD_WRITE_DMA_EX @@: mov ebx, dword [startsector] mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.lba0], bl shr ebx, 8 mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.lba1], bl shr ebx, 8 mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.lba2], bl mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.device], 1 shl 6 ; LBA mode shr ebx, 8 mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.lba3], bl mov ebx, dword [startsector + 4] mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.lba4], bl shr ebx, 8 mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.lba5], bl mov ebx, [numsectors] mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.countl], bl shr ebx, 8 mov byte [eax + HBA_CMD_TBL.cfis + FIS_REG_H2D.counth], bl ; Wait on previous command to complete, before issuing new command. stdcall ahci_port_wait, edi, AHCI_PORT_TIMEOUT mov eax, [cmdslot] bts [edi + HBA_PORT.command_issue], eax ; Issue the command ; Wait for command completion stdcall ahci_port_cmd_wait, edi, eax;, AHCI_PORT_CMD_TIMEOUT DEBUGF AHCI_DBGLVL, "sata_error register = 0x%x\n", [edi + HBA_PORT.sata_error] DEBUGF AHCI_DBGLVL, "R/W completed\n" ; xor ecx, ecx ; mov esi, [vbuf_orig] ; .print_data: ; cmp ecx, 512 ; jae .end_print_data ; mov al, byte [esi + ecx] ; mov byte [tmpstr], al ; mov byte [tmpstr + 1], 0 ; DEBUGF 1, "0x%x(%s) ", al:2, tmpstr ; inc ecx ; jmp .print_data ; .end_print_data: ; DEBUGF 1, "\n" popad ;mov eax, [cmdheader] ;mov eax, [eax + HBA_CMD_HDR.prdbc] mov eax, [numsectors] shl eax, 9 ; *= 512 ret .fail: popad xor eax, eax ret endp tmpstr rb 16 ; Read sectors ; return value: 0 = success, otherwise = error proc ahci_read stdcall pdata: dword, buffer: dword, startsector: qword, numsectors_ptr:dword locals numsectors dd ? endl pushad mov ecx, sd1_data.ahci_mutex call mutex_lock mov eax, [numsectors_ptr] mov eax, [eax] mov [numsectors], eax DEBUGF AHCI_DBGLVL, " ahci_read: buffer = 0x%x, startsector = 0x%x:%x, numsectors = %u\n", [buffer], [startsector], [startsector + 4], eax xor ecx, ecx ; how many sectors have been read .read_loop: cmp ecx, [numsectors] jae .read_loop_end ; mov eax, [buffer] ; call get_pg_addr ; DEBUGF 1, "buf phys = 0x%x\n", eax ; mov eax, [buffer] ; add eax, 4096 ; call get_pg_addr ; DEBUGF 1, "buf + 4096 phys = 0x%x\n", eax mov ebx, [numsectors] sub ebx, ecx ; DEBUGF 1, "buffer = 0x%x\n", [buffer] stdcall ahci_rw_sectors, [pdata], [buffer], dword [startsector], dword [startsector + 4], ebx, 0 ;; TODO check if eax == 0 ? DEBUGF AHCI_DBGLVL, " EAX = 0x%x\n", eax add [buffer], eax shr eax, 9 ; /= 512 add ecx, eax add dword [startsector], eax adc dword [startsector + 4], 0 jmp .read_loop .read_loop_end: mov ecx, sd1_data.ahci_mutex call mutex_unlock popad xor eax, eax ret endp ; Write sectors ; return value: 0 = success, otherwise = error proc ahci_write stdcall pdata: dword, buffer: dword, startsector: qword, numsectors_ptr:dword locals numsectors dd ? endl pushad mov ecx, sd1_data.ahci_mutex call mutex_lock mov eax, [numsectors_ptr] mov eax, [eax] mov [numsectors], eax DEBUGF AHCI_DBGLVL, " ahci_write: buffer = 0x%x, startsector = 0x%x:%x, numsectors = %u\n", [buffer], [startsector], [startsector + 4], eax xor ecx, ecx ; how many sectors have been read .write_loop: cmp ecx, [numsectors] jae .write_loop_end mov ebx, [numsectors] sub ebx, ecx stdcall ahci_rw_sectors, [pdata], [buffer], dword [startsector], dword [startsector + 4], ebx, 1 ;; TODO check if eax == 0 ? DEBUGF AHCI_DBGLVL, " EAX = 0x%x\n", eax add [buffer], eax shr eax, 9 ; /= 512 add ecx, eax add dword [startsector], eax adc dword [startsector + 4], 0 jmp .write_loop .write_loop_end: mov ecx, sd1_data.ahci_mutex call mutex_unlock popad xor eax, eax ret endp ; Start command engine ; in: eax - address of HBA_PORT structure ahci_start_cmd: .wait_cr: ; Wait until CR (bit15) is cleared bt [eax + HBA_PORT.command], bit_AHCI_HBA_PxCMD_CR jc .wait_cr ; Set FRE (bit4) and ST (bit0) bts [eax + HBA_PORT.command], bit_AHCI_HBA_PxCMD_FRE bts [eax + HBA_PORT.command], bit_AHCI_HBA_PxCMD_ST ; maybe here call ahci flush cmd ? TODO (see seakernel) ret ; Stop command engine ; in: eax - address of HBA_PORT structure ahci_stop_cmd: btr [eax + HBA_PORT.command], bit_AHCI_HBA_PxCMD_ST ; Clear ST (bit0) btr [eax + HBA_PORT.command], bit_AHCI_HBA_PxCMD_FRE ; Clear FRE (bit4) .wait_fr_cr: ; Wait until FR (bit14), CR (bit15) are cleared bt [eax + HBA_PORT.command], bit_AHCI_HBA_PxCMD_FR jc .wait_fr_cr bt [eax + HBA_PORT.command], bit_AHCI_HBA_PxCMD_CR jc .wait_fr_cr ret ; waits until the port is no longer busy before issuing a new command ; in: [port] - address of HBA_PORT structure ; [timeout] - timeout (in iterations) ; out: eax = 0 if success, 1 if timeout expired proc ahci_port_wait stdcall, port: dword, timeout: dword push ebx ecx mov ebx, [port] xor ecx, ecx .wait: cmp ecx, [timeout] jae .wait_end mov eax, [ebx + HBA_PORT.task_file_data] and eax, ATA_DEV_BUSY or ATA_DEV_DRQ test eax, eax jz .wait_end inc ecx jmp .wait .wait_end: xor eax, eax DEBUGF AHCI_DBGLVL, "port wait counter = %u\n", ecx cmp ecx, [timeout] ; if they equal it means port is hung setz al pop ecx ebx ret endp ; Wait for command completion ; in: [port] - address of HBA_PORT structure ; [cmdslot] - number of command slot ; out: eax = 0 if success, 1 if error proc ahci_port_cmd_wait stdcall, port: dword, cmdslot: dword ;, timeout: dword push ebx ecx edx mov ebx, [port] mov edx, [cmdslot] xor eax, eax xor ecx, ecx .wait: bt [ebx + HBA_PORT.command_issue], edx jnc .wait_end bt [ebx + HBA_PORT.interrupt_status], bit_AHCI_HBA_PxIS_TFES ; check for Task File Error jc .error inc ecx jmp .wait .wait_end: DEBUGF AHCI_DBGLVL, "port cmd wait counter = %u\n", ecx bt [ebx + HBA_PORT.interrupt_status], bit_AHCI_HBA_PxIS_TFES ; check for Task File Error jc .error jmp .ret .error: mov eax, 1 .ret: pop edx ecx ebx ret endp ; ; The commands may not take effect until the command ; ; register is read again by software, because reasons. ; ; in: eax - address of HBA_PORT structure ; ; out: eax - command register value ; ahci_flush_cmd: ; mov eax, [eax + HBA_PORT.command] ; ret ; ; Send command to port ; ; in: eax - address of HBA_PORT structure ; ; ebx - index of command slot ; ahci_send_cmd: ; push ecx ; mov [eax + HBA_PORT.interrupt_status], 0xFFFFFFFF ; mov cl, bl ; mov [eax + HBA_PORT.command_issue], 1 ; shl [eax + HBA_PORT.command_issue], cl ; call ahci_flush_cmd ; pop ecx ; ret ; --------------------------------------------------------------------------- ; in: port - address of HBA_PORT structure ; portno - port index (0..31) ; pdata - address of PORT_DATA structure proc ahci_port_rebase stdcall, port: dword, portno: dword, pdata: dword locals phys_page1 dd ? virt_page1 dd ? phys_page23 dd ? virt_page23 dd ? tmp dd ? endl pushad DEBUGF 1, "Rebasing port %u\n", [portno] mov eax, [port] call ahci_stop_cmd ; Command list entry size = 32 ; Command list entry maxim count = 32 ; Command list maxim size = 32*32 = 1K per port call alloc_page mov [phys_page1], eax stdcall map_io_mem, eax, 4096, PG_NOCACHE + PG_SWR ; map to virt memory so we can work with it mov [virt_page1], eax mov esi, [port] mov ebx, [phys_page1] mov [esi + HBA_PORT.command_list_base_l], ebx ; set the command list base mov [esi + HBA_PORT.command_list_base_h], 0 ; zero upper 32 bits of addr cause we are 32 bit os mov edi, [pdata] mov ebx, [virt_page1] mov [edi + PORT_DATA.clb], ebx ; set pdata->clb mov eax, [port] mov [edi + PORT_DATA.port], eax ; set pdata->port mov eax, [portno] ; set pdata->portno mov [edi + PORT_DATA.portno], eax stdcall _memset, ebx, 0, 1024 ; zero out the command list ; FIS entry size = 256 bytes per port mov eax, [phys_page1] add eax, 1024 mov [esi + HBA_PORT.fis_base_l], eax mov [esi + HBA_PORT.fis_base_h], 0 mov eax, [virt_page1] add eax, 1024 mov [edi + PORT_DATA.fb], eax ; set pdata->fb stdcall _memset, eax, 0, 256 ; zero out stdcall alloc_pages, 32*(64 + 16 + 48 + PRDT_MAX_ENTRIES*16)/4096 mov [phys_page23], eax stdcall map_io_mem, eax, 32*(64 + 16 + 48 + PRDT_MAX_ENTRIES*16), PG_NOCACHE + PG_SWR mov [virt_page23], eax ; Command table size = N*32 per port mov edx, [edi + PORT_DATA.clb] ; cmdheader array base xor ecx, ecx .for1: cmp ecx, 32 jae .for1_end mov ebx, ecx shl ebx, BSF sizeof.HBA_CMD_HDR add ebx, edx ; ebx = cmdheader[ecx] mov [ebx + HBA_CMD_HDR.prdtl], PRDT_MAX_ENTRIES ; prdt entries per command table ; bytes per command table = 64+16+48+PRDT_MAX_ENTRIES*16 = N push edx ; cmdheader[ecx].ctba = phys_page23 + ecx*N mov [ebx + HBA_CMD_HDR.ctba], ecx mov edx, [ebx + HBA_CMD_HDR.ctba] imul edx, (64+16+48+PRDT_MAX_ENTRIES*16) ; *= N mov [ebx + HBA_CMD_HDR.ctba], edx mov eax, [ebx + HBA_CMD_HDR.ctba] mov edx, [phys_page23] add [ebx + HBA_CMD_HDR.ctba], edx add eax, [virt_page23] mov [tmp], eax ; tmp = virt_page23 + ecx*N lea eax, [ecx*4 + edi + PORT_DATA.ctba_arr] ; eax = pdata->ctba_arr[ecx] mov edx, [tmp] mov [eax], edx ; pdata->ctba_arr[ecx] = virt_page23 + ecx*N pop edx mov [ebx + HBA_CMD_HDR.ctbau], 0 stdcall _memset, [eax], 0, 64+16+48+PRDT_MAX_ENTRIES*16 ; zero out inc ecx jmp .for1 .for1_end: mov eax, [port] call ahci_start_cmd DEBUGF 1, "End rebasing port %u\n", [portno] popad ret endp ; ----------------------------------------------------------- ; TODO check ; Find a free command list slot ; in: eax - address of HBA_PORT structure ; out: eax - if not found -1, else slot index ahci_find_cmdslot: push ebx ecx edx esi ; If not set in SACT and CI, the slot is free mov ebx, [eax + HBA_PORT.sata_active] or ebx, [eax + HBA_PORT.command_issue] ; ebx = slots mov esi, [sd1_data.ahci_controller + AHCI_DATA.abar] mov edx, [esi + HBA_MEM.cap] shr edx, 8 and edx, 0xf ; DEBUGF 1, "Number of Command Slots on each port = %u\n", edx xor ecx, ecx .for1: cmp ecx, edx jae .for1_end ; if ((slots&1) == 0) return i; bt ebx, 0 jc .cont1 mov eax, ecx jmp .ret .cont1: shr ebx, 1 inc ecx jmp .for1 .for1_end: DEBUGF 1, "Cannot find free command list entry\n" mov eax, -1 .ret: pop esi edx ecx ebx ret proc _memset stdcall, dest:dword, val:byte, cnt:dword ; doesnt clobber any registers ;DEBUGF DBG_INFO, "memset(%x, %u, %u)\n", [dest], [val], [cnt] push eax ecx edi mov edi, dword [dest] mov al, byte [val] mov ecx, dword [cnt] rep stosb pop edi ecx eax ret endp ; Swaps byte order in words ; base - address of first word ; len - how many words to swap bytes in ; doesnt clobber any registers proc swap_bytes_in_words stdcall, base: dword, len: dword push eax ebx ecx xor ecx, ecx mov ebx, [base] .loop: cmp ecx, [len] jae .loop_end mov ax, word [ebx + ecx*2] xchg ah, al mov word [ebx + ecx*2], ax inc ecx jmp .loop .loop_end: pop ecx ebx eax ret endp