;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; Copyright (C) KolibriOS team 2004-2015. All rights reserved. ;; ;; Distributed under terms of the GNU General Public License ;; ;; ;; ;; R6040 driver for KolibriOS ;; ;; ;; ;; based on R6040.c from linux ;; ;; ;; ;; Written by Asper (asper.85@mail.ru) ;; ;; and hidnplayr (hidnplayr@gmail.com) ;; ;; ;; ;; GNU GENERAL PUBLIC LICENSE ;; ;; Version 2, June 1991 ;; ;; ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; format PE DLL native entry START CURRENT_API = 0x0200 COMPATIBLE_API = 0x0100 API_VERSION = (COMPATIBLE_API shl 16) + CURRENT_API MAX_DEVICES = 16 __DEBUG__ = 1 __DEBUG_LEVEL__ = 2 W_MAX_TIMEOUT = 0x0FFF ; max time out delay time TX_TIMEOUT = 6000 ; Time before concluding the transmitter is hung, in ms TX_RING_SIZE = 4 ; RING sizes must be a power of 2 RX_RING_SIZE = 4 RX_BUF_LEN_IDX = 3 ; 0==8K, 1==16K, 2==32K, 3==64K ; Threshold is bytes transferred to chip before transmission starts. TX_FIFO_THRESH = 256 ; In bytes, rounded down to 32 byte units. ; The following settings are log_2(bytes)-4: 0 == 16 bytes .. 6==1024. RX_FIFO_THRESH = 4 ; Rx buffer level before first PCI xfer. RX_DMA_BURST = 4 ; Maximum PCI burst, '4' is 256 bytes TX_DMA_BURST = 4 section '.flat' readable writable executable include '../proc32.inc' include '../struct.inc' include '../macros.inc' include '../fdo.inc' include '../netdrv.inc' ; Operational parameters that usually are not changed. PHY1_ADDR = 1 ; For MAC1 PHY2_ADDR = 3 ; For MAC2 PHY_MODE = 0x3100 ; PHY CHIP Register 0 PHY_CAP = 0x01E1 ; PHY CHIP Register 4 ;************************************************************************** ; RDC R6040 Register Definitions ;************************************************************************** MCR0 = 0x00 ; Control register 0 MCR0_RCVEN = 0x0002 ; Receive enable MCR0_PROMISC = 0x0020 ; Promiscuous mode MCR0_HASH_EN = 0x0100 ; Enable multicast hash table function MCR0_XMTEN = 0x1000 ; Transmission enable MCR0_FD = 0x8000 ; Full/Half Duplex mode MCR1 = 0x01 ; Control register 1 MAC_RST = 0x0001 ; Reset the MAC MBCR = 0x08 ; Bus control MT_ICR = 0x0C ; TX interrupt control MR_ICR = 0x10 ; RX interrupt control MTPR = 0x14 ; TX poll command register MR_BSR = 0x18 ; RX buffer size MR_DCR = 0x1A ; RX descriptor control MLSR = 0x1C ; Last status MMDIO = 0x20 ; MDIO control register MDIO_WRITE = 0x4000 ; MDIO write MDIO_READ = 0x2000 ; MDIO read MMRD = 0x24 ; MDIO read data register MMWD = 0x28 ; MDIO write data register MTD_SA0 = 0x2C ; TX descriptor start address 0 MTD_SA1 = 0x30 ; TX descriptor start address 1 MRD_SA0 = 0x34 ; RX descriptor start address 0 MRD_SA1 = 0x38 ; RX descriptor start address 1 MISR = 0x3C ; Status register MIER = 0x40 ; INT enable register MSK_INT = 0x0000 ; Mask off interrupts RX_FINISH = 0x0001 ; RX finished RX_NO_DESC = 0x0002 ; No RX descriptor available RX_FIFO_FULL = 0x0004 ; RX FIFO full RX_EARLY = 0x0008 ; RX early TX_FINISH = 0x0010 ; TX finished TX_EARLY = 0x0080 ; TX early EVENT_OVRFL = 0x0100 ; Event counter overflow LINK_CHANGED = 0x0200 ; PHY link changed ME_CISR = 0x44 ; Event counter INT status ME_CIER = 0x48 ; Event counter INT enable MR_CNT = 0x50 ; Successfully received packet counter ME_CNT0 = 0x52 ; Event counter 0 ME_CNT1 = 0x54 ; Event counter 1 ME_CNT2 = 0x56 ; Event counter 2 ME_CNT3 = 0x58 ; Event counter 3 MT_CNT = 0x5A ; Successfully transmit packet counter ME_CNT4 = 0x5C ; Event counter 4 MP_CNT = 0x5E ; Pause frame counter register MAR0 = 0x60 ; Hash table 0 MAR1 = 0x62 ; Hash table 1 MAR2 = 0x64 ; Hash table 2 MAR3 = 0x66 ; Hash table 3 MID_0L = 0x68 ; Multicast address MID0 Low MID_0M = 0x6A ; Multicast address MID0 Medium MID_0H = 0x6C ; Multicast address MID0 High MID_1L = 0x70 ; MID1 Low MID_1M = 0x72 ; MID1 Medium MID_1H = 0x74 ; MID1 High MID_2L = 0x78 ; MID2 Low MID_2M = 0x7A ; MID2 Medium MID_2H = 0x7C ; MID2 High MID_3L = 0x80 ; MID3 Low MID_3M = 0x82 ; MID3 Medium MID_3H = 0x84 ; MID3 High PHY_CC = 0x88 ; PHY status change configuration register PHY_ST = 0x8A ; PHY status register MAC_SM = 0xAC ; MAC status machine MAC_ID = 0xBE ; Identifier register MAX_BUF_SIZE = 0x600 ; 1536 MBCR_DEFAULT = 0x012A ; MAC Bus Control Register MCAST_MAX = 3 ; Max number multicast addresses to filter ;Descriptor status DSC_OWNER_MAC = 0x8000 ; MAC is the owner of this descriptor DSC_RX_OK = 0x4000 ; RX was successfull DSC_RX_ERR = 0x0800 ; RX PHY error DSC_RX_ERR_DRI = 0x0400 ; RX dribble packet DSC_RX_ERR_BUF = 0x0200 ; RX length exceeds buffer size DSC_RX_ERR_LONG = 0x0100 ; RX length > maximum packet length DSC_RX_ERR_RUNT = 0x0080 ; RX packet length < 64 byte DSC_RX_ERR_CRC = 0x0040 ; RX CRC error DSC_RX_BCAST = 0x0020 ; RX broadcast (no error) DSC_RX_MCAST = 0x0010 ; RX multicast (no error) DSC_RX_MCH_HIT = 0x0008 ; RX multicast hit in hash table (no error) DSC_RX_MIDH_HIT = 0x0004 ; RX MID table hit (no error) DSC_RX_IDX_MID_MASK = 3 ; RX mask for the index of matched MIDx ;PHY settings ICPLUS_PHY_ID = 0x0243 RX_INTS = RX_FIFO_FULL or RX_NO_DESC or RX_FINISH TX_INTS = TX_FINISH INT_MASK = RX_INTS or TX_INTS RX_BUF_LEN equ (8192 << RX_BUF_LEN_IDX) ; Size of the in-memory receive ring. IO_SIZE = 256 ; RDC MAC I/O Size MAX_MAC = 2 ; MAX RDC MAC struct x_head status dw ? ;0-1 len dw ? ;2-3 buf dd ? ;4-7 ndesc dd ? ;8-B rev1 dd ? ;C-F vbufp dd ? ;10-13 vndescp dd ? ;14-17 skb_ptr dd ? ;18-1B rev2 dd ? ;1C-1F ends struct device ETH_DEVICE io_addr dd ? pci_bus dd ? pci_dev dd ? irq_line db ? rb 3 ; align 4 cur_rx dw ? cur_tx dw ? last_tx dw ? phy_addr dd ? phy_mode dw ? mcr0 dw ? mcr1 dw ? switch_sig dw ? rb 0x100 - ($ and 0xff) ; align 256 tx_ring rb ((TX_RING_SIZE*sizeof.x_head+32) and 0xfffffff0) rx_ring rb ((RX_RING_SIZE*sizeof.x_head+32) and 0xfffffff0) ends ;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; proc START ;; ;; ;; ;; (standard driver proc) ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;; proc START c, reason:dword, cmdline:dword cmp [reason], DRV_ENTRY jne .fail DEBUGF 2,"Loading driver\n" invoke RegService, my_service, service_proc ret .fail: xor eax, eax ret endp ;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; proc SERVICE_PROC ;; ;; ;; ;; (standard driver proc) ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;; proc service_proc stdcall, ioctl:dword mov edx, [ioctl] mov eax, [edx + IOCTL.io_code] ;------------------------------------------------------ cmp eax, 0 ;SRV_GETVERSION jne @F cmp [edx + IOCTL.out_size], 4 jb .fail mov eax, [edx + IOCTL.output] mov [eax], dword API_VERSION xor eax, eax ret ;------------------------------------------------------ @@: cmp eax, 1 ;SRV_HOOK jne .fail cmp [edx + IOCTL.inp_size], 3 ; Data input must be at least 3 bytes jb .fail mov eax, [edx + IOCTL.input] cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given jne .fail ; other types arent supported for this card yet ; check if the device is already listed mov esi, device_list mov ecx, [devices] test ecx, ecx jz .firstdevice ; mov eax, [edx + IOCTL.input] ; get the pci bus and device numbers mov ax , [eax+1] ; .nextdevice: mov ebx, [esi] cmp al, byte[ebx + device.pci_bus] jne @f cmp ah, byte[ebx + device.pci_dev] je .find_devicenum ; Device is already loaded, let's find it's device number @@: add esi, 4 loop .nextdevice ; This device doesnt have its own eth_device structure yet, lets create one .firstdevice: cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card jae .fail allocate_and_clear ebx, sizeof.device, .fail ; Allocate the buffer for device structure ; Fill in the direct call addresses into the struct mov [ebx + device.reset], reset mov [ebx + device.transmit], transmit mov [ebx + device.unload], unload mov [ebx + device.name], my_service ; save the pci bus and device numbers mov eax, [edx + IOCTL.input] movzx ecx, byte[eax+1] mov [ebx + device.pci_bus], ecx movzx ecx, byte[eax+2] mov [ebx + device.pci_dev], ecx ; Now, it's time to find the base io addres of the PCI device stdcall PCI_find_io, [ebx + device.pci_bus], [ebx + device.pci_dev] mov [ebx + device.io_addr], eax ; We've found the io address, find IRQ now invoke PciRead8, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.interrupt_line mov [ebx + device.irq_line], al DEBUGF 1,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\ [ebx + device.pci_dev]:1,[ebx + device.pci_bus]:1,[ebx + device.irq_line]:1,[ebx + device.io_addr]:8 ; Ok, the eth_device structure is ready, let's probe the device mov eax, [devices] ; Add the device structure to our device list mov [device_list+4*eax], ebx ; (IRQ handler uses this list to find device) inc [devices] ; call probe ; this function will output in eax test eax, eax jnz .err2 DEBUGF 2,"Initialised OK\n" mov [ebx + device.type], NET_TYPE_ETH invoke NetRegDev cmp eax, -1 je .destroy ret ; If the device was already loaded, find the device number and return it in eax .find_devicenum: DEBUGF 2,"Trying to find device number of already registered device\n" invoke NetPtrToNum ; This kernel procedure converts a pointer to device struct in ebx ; into a device number in edi mov eax, edi ; Application wants it in eax instead DEBUGF 2,"Kernel says: %u\n", eax ret ; If an error occured, remove all allocated data and exit (returning -1 in eax) .destroy: ; todo: reset device into virgin state .err2: dec [devices] .err: invoke KernelFree, ebx .fail: DEBUGF 2, "Failed to load\n" or eax, -1 ret ;------------------------------------------------------ endp ;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;; ;; ;; ;; Actual Hardware dependent code starts here ;; ;; ;; ;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;; ;mdio_read: ; stdcall phy_read, [ebx + device.io_addr], [ebx + device.phy_addr], ecx ; ret ;mdio_write: ; stdcall phy_write, [ebx + device.io_addr], [ebx + device.phy_addr], ecx, eax ; ret align 4 unload: ; TODO: (in this particular order) ; ; - Stop the device ; - Detach int handler ; - Remove device from local list (RTL8139_LIST) ; - call unregister function in kernel ; - Remove all allocated structures and buffers the card used or eax,-1 ret ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; probe: enables the device (if it really is R6040) ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; align 4 probe: DEBUGF 1,"Probing\n" ; Make the device a bus master invoke PciRead32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command or al, PCI_CMD_MASTER invoke PciWrite32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command, eax ; If PHY status change register is still set to zero ; it means the bootloader didn't initialize it set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], PHY_CC in ax, dx test ax, ax jnz @f mov ax, 0x9F07 out dx, ax @@: call read_mac ; Some bootloaders/BIOSes do not initialize MAC address, warn about that and eax, 0xFF or eax, dword [ebx + device.mac] test eax, eax jnz @f DEBUGF 2, "MAC address not initialized!\n" @@: ; Init RDC private data mov [ebx + device.mcr0], MCR0_XMTEN or MCR0_RCVEN mov [ebx + device.phy_addr], PHY1_ADDR mov [ebx + device.switch_sig], 0 ; Check the vendor ID on the PHY, if 0xFFFF assume none attached stdcall phy_read, [ebx + device.phy_addr], 2 cmp ax, 0xFFFF jne @f DEBUGF 2, "Failed to detect an attached PHY!\n" mov eax, -1 ret @@: ; Set MAC address call init_mac_regs ; Initialize and alloc RX/TX buffers call init_txbufs call init_rxbufs ; Read the PHY ID mov [ebx + device.phy_mode], MCR0_FD stdcall phy_read, 0, 2 mov [ebx + device.switch_sig], ax cmp ax, ICPLUS_PHY_ID jne @f stdcall phy_write, 29, 31, 0x175C ; Enable registers jmp .phy_readen @@: ; PHY Mode Check stdcall phy_write, [ebx + device.phy_addr], 4, PHY_CAP stdcall phy_write, [ebx + device.phy_addr], 0, PHY_MODE if PHY_MODE = 0x3100 call phy_mode_chk mov [ebx + device.phy_mode], ax jmp .phy_readen end if if not (PHY_MODE and 0x0100) mov [ebx + device.phy_mode], 0 end if .phy_readen: ; Set duplex mode mov ax, [ebx + device.phy_mode] or [ebx + device.mcr0], ax ; improve performance (by RDC guys) stdcall phy_read, 30, 17 or ax, 0x4000 stdcall phy_write, 30, 17, eax stdcall phy_read, 30, 17 and ax, not 0x2000 stdcall phy_write, 30, 17, eax stdcall phy_write, 0, 19, 0x0000 stdcall phy_write, 0, 30, 0x01F0 ; Initialize all Mac registers call init_mac_regs align 4 reset: DEBUGF 1,"Resetting\n" ; Mask off Interrupt xor ax, ax set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], MIER out dx, ax ; attach int handler movzx eax, [ebx + device.irq_line] DEBUGF 1,"Attaching int handler to irq %x\n", eax:1 invoke AttachIntHandler, eax, int_handler, ebx test eax, eax jnz @f DEBUGF 2,"Could not attach int handler!\n" or eax, -1 ret @@: ;Reset RDC MAC mov eax, MAC_RST set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], MCR1 out dx, ax mov ecx, 2048 ;limit .read: in ax, dx test ax, 0x1 jnz @f dec ecx test ecx, ecx jnz .read @@: ;Reset internal state machine mov ax, 2 set_io [ebx + device.io_addr], MAC_SM out dx, ax xor ax, ax out dx, ax mov esi, 5 invoke Sleep ;MAC Bus Control Register mov ax, MBCR_DEFAULT set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], MBCR out dx, ax ;Buffer Size Register mov ax, MAX_BUF_SIZE set_io [ebx + device.io_addr], MR_BSR out dx, ax ;Write TX ring start address lea eax, [ebx + device.tx_ring] invoke GetPhysAddr set_io [ebx + device.io_addr], MTD_SA0 out dx, ax shr eax, 16 set_io [ebx + device.io_addr], MTD_SA1 out dx, ax ;Write RX ring start address lea eax, [ebx + device.rx_ring] invoke GetPhysAddr set_io [ebx + device.io_addr], MRD_SA0 out dx, ax shr eax, 16 set_io [ebx + device.io_addr], MRD_SA1 out dx, ax ;Set interrupt waiting time and packet numbers xor ax, ax set_io [ebx + device.io_addr], MT_ICR out dx, ax ;Enable interrupts mov ax, INT_MASK set_io [ebx + device.io_addr], MIER out dx, ax ;Enable RX mov ax, [ebx + device.mcr0] or ax, MCR0_RCVEN set_io [ebx + device.io_addr], 0 out dx, ax ;Let TX poll the descriptors ;we may got called by tx_timeout which has left some unset tx buffers xor ax, ax inc ax set_io [ebx + device.io_addr], MTPR out dx, ax ; Set the mtu, kernel will be able to send now mov [ebx + device.mtu], 1514 ; Set link state to unknown mov [ebx + device.state], ETH_LINK_UNKNOWN DEBUGF 1,"Reset ok\n" xor eax, eax ret align 4 init_txbufs: DEBUGF 1,"Init TxBufs\n" lea esi, [ebx + device.tx_ring] lea eax, [ebx + device.tx_ring + sizeof.x_head] invoke GetPhysAddr mov ecx, TX_RING_SIZE .next_desc: mov [esi + x_head.ndesc], eax mov [esi + x_head.skb_ptr], 0 mov [esi + x_head.status], DSC_OWNER_MAC add eax, sizeof.x_head add esi, sizeof.x_head dec ecx jnz .next_desc lea eax, [ebx + device.tx_ring] invoke GetPhysAddr mov dword[ebx + device.tx_ring + sizeof.x_head*(TX_RING_SIZE-1) + x_head.ndesc], eax ret align 4 init_rxbufs: DEBUGF 1,"Init RxBufs\n" lea esi, [ebx + device.rx_ring] lea eax, [ebx + device.rx_ring + sizeof.x_head] invoke GetPhysAddr mov edx, eax mov ecx, RX_RING_SIZE .next_desc: mov [esi + x_head.ndesc], edx push esi ecx edx invoke KernelAlloc, MAX_BUF_SIZE pop edx ecx esi mov [esi + x_head.skb_ptr], eax invoke GetPhysAddr mov [esi + x_head.buf], eax mov [esi + x_head.status], DSC_OWNER_MAC add edx, sizeof.x_head add esi, sizeof.x_head dec ecx jnz .next_desc ; complete the ring by linking the last to the first lea eax, [ebx + device.rx_ring] invoke GetPhysAddr mov dword[ebx + device.rx_ring + sizeof.x_head*(RX_RING_SIZE-1) + x_head.ndesc], eax ret align 4 phy_mode_chk: DEBUGF 1,"Checking PHY mode\n" ; PHY Link Status Check stdcall phy_read, [ebx + device.phy_addr], MII_BMSR test ax, BMSR_LSTATUS jz .ret_0x8000 ; PHY Chip Auto-Negotiation Status test ax, BMSR_ANEGCOMPLETE jnz .auto_nego ; Force Mode stdcall phy_read, [ebx + device.phy_addr], MII_BMCR test ax, BMCR_FULLDPLX jnz .ret_0x8000 .auto_nego: ; Auto Negotiation Mode stdcall phy_read, [ebx + device.phy_addr], MII_LPA mov cx, ax stdcall phy_read, [ebx + device.phy_addr], MII_ADVERTISE and ax, cx test ax, ADVERTISE_10FULL + ADVERTISE_100FULL jnz .ret_0x8000 xor eax, eax ret .ret_0x8000: mov eax, 0x8000 ret ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; Transmit ;; ;; ;; ;; In: pointer to device structure in ebx ;; ;; ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; proc transmit stdcall bufferptr, buffersize pushf cli DEBUGF 1,"Transmitting packet, buffer:%x, size:%u\n", [bufferptr], [buffersize] mov eax, [bufferptr] DEBUGF 1,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\ [eax+00]:2,[eax+01]:2,[eax+02]:2,[eax+03]:2,[eax+04]:2,[eax+05]:2,\ [eax+06]:2,[eax+07]:2,[eax+08]:2,[eax+09]:2,[eax+10]:2,[eax+11]:2,\ [eax+13]:2,[eax+12]:2 cmp [buffersize], 1514 ja .fail cmp [buffersize], 60 jb .fail movzx edi, [ebx + device.cur_tx] shl edi, 5 add edi, ebx add edi, device.tx_ring DEBUGF 1,"TX buffer status: 0x%x\n", [edi + x_head.status]:4 test [edi + x_head.status], DSC_OWNER_MAC ; check if buffer is available jnz .wait_to_send .do_send: DEBUGF 1,"Sending now\n" mov eax, [bufferptr] mov [edi + x_head.skb_ptr], eax invoke GetPhysAddr mov [edi + x_head.buf], eax mov ecx, [buffersize] mov [edi + x_head.len], cx mov [edi + x_head.status], DSC_OWNER_MAC ; Trigger the MAC to check the TX descriptor mov ax, 0x01 set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], MTPR out dx, ax inc [ebx + device.cur_tx] and [ebx + device.cur_tx], TX_RING_SIZE - 1 ; Update stats inc [ebx + device.packets_tx] mov eax, [buffersize] add dword[ebx + device.bytes_tx], eax adc dword[ebx + device.bytes_tx + 4], 0 popf xor eax, eax ret .wait_to_send: DEBUGF 1,"Waiting for TX buffer\n" invoke GetTimerTicks ; returns in eax lea edx, [eax + 100] .l2: test [edi + x_head.status], DSC_OWNER_MAC jz .do_send mov esi, 10 invoke Sleep invoke GetTimerTicks cmp edx, eax jb .l2 DEBUGF 2,"Send timeout\n" .fail: DEBUGF 2,"Send failed\n" invoke KernelFree, [bufferptr] popf or eax, -1 ret endp ;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; Interrupt handler ;; ;; ;; ;;;;;;;;;;;;;;;;;;;;;;; align 4 int_handler: push ebx esi edi DEBUGF 1,"int\n" ; Find pointer of device wich made IRQ occur mov ecx, [devices] test ecx, ecx jz .nothing mov esi, device_list .nextdevice: mov ebx, [esi] set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], MISR in ax, dx out dx, ax ; send it back to ACK test ax, ax jnz .got_it .continue: add esi, 4 dec ecx jnz .nextdevice .nothing: pop edi esi ebx xor eax, eax ret ; If no device was found, abort ; At this point, test for all possible reasons, and handle accordingly .got_it: DEBUGF 1,"Device: %x Status: %x\n", ebx, ax push ax test word[esp], RX_FINISH jz .no_RX push ebx .more_RX: pop ebx ; Find the current RX descriptor movzx edx, [ebx + device.cur_rx] shl edx, 5 lea edx, [ebx + device.rx_ring + edx] ; Check the descriptor status mov cx, [edx + x_head.status] test cx, DSC_OWNER_MAC jnz .no_RX DEBUGF 1,"packet status=0x%x\n", cx test cx, DSC_RX_ERR ; Global error status set jnz .no_RX ; Packet successfully received movzx ecx, [edx + x_head.len] and ecx, 0xFFF sub ecx, 4 ; Do not count the CRC ; Update stats add dword[ebx + device.bytes_rx], ecx adc dword[ebx + device.bytes_rx + 4], 0 inc dword[ebx + device.packets_rx] ; Push packet size and pointer, kernel will need it.. push ebx push .more_RX push ecx push [edx + x_head.skb_ptr] DEBUGF 1,"packet ptr=0x%x\n", [edx + x_head.skb_ptr] ; reset the RX descriptor push edx invoke KernelAlloc, MAX_BUF_SIZE pop edx mov [edx + x_head.skb_ptr], eax invoke GetPhysAddr mov [edx + x_head.buf], eax mov [edx + x_head.status], DSC_OWNER_MAC ; Use next descriptor next time inc [ebx + device.cur_rx] and [ebx + device.cur_rx], RX_RING_SIZE - 1 ; At last, send packet to kernel jmp [Eth_input] .no_RX: test word[esp], TX_FINISH jz .no_TX .loop_tx: movzx edi, [ebx + device.last_tx] shl edi, 5 lea edi, [ebx + device.tx_ring + edi] test [edi + x_head.status], DSC_OWNER_MAC jnz .no_TX cmp [edi + x_head.skb_ptr], 0 je .no_TX DEBUGF 1,"Freeing buffer 0x%x\n", [edi + x_head.skb_ptr] push [edi + x_head.skb_ptr] mov [edi + x_head.skb_ptr], 0 invoke KernelFree inc [ebx + device.last_tx] and [ebx + device.last_tx], TX_RING_SIZE - 1 jmp .loop_tx .no_TX: test word[esp], RX_NO_DESC jz .no_rxdesc DEBUGF 2, "No more RX descriptors!\n" .no_rxdesc: test word[esp], RX_FIFO_FULL jz .no_rxfifo DEBUGF 2, "RX FIFO full!\n" .no_rxfifo: test word[esp], RX_EARLY jz .no_rxearly DEBUGF 2, "RX early\n" .no_rxearly: test word[esp], TX_EARLY jz .no_txearly DEBUGF 2, "TX early\n" .no_txearly: test word[esp], EVENT_OVRFL jz .no_ovrfl DEBUGF 2, "Event counter overflow!\n" .no_ovrfl: test word[esp], LINK_CHANGED jz .no_link DEBUGF 2, "Link changed\n" .no_link: pop ax pop edi esi ebx ret align 4 init_mac_regs: DEBUGF 1,"initializing MAC regs\n" ; MAC operation register mov ax, 1 set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], MCR1 out dx, ax ; Reset MAC mov ax, 2 set_io [ebx + device.io_addr], MAC_SM out dx, ax ; Reset internal state machine xor ax, ax out dx, ax mov esi, 5 invoke Sleep call read_mac ret ; Read a word data from PHY Chip align 4 proc phy_read stdcall, phy_addr:dword, reg:dword DEBUGF 1,"PHY read, addr=0x%x reg=0x%x\n", [phy_addr]:8, [reg]:8 mov eax, [phy_addr] shl eax, 8 add eax, [reg] add eax, MDIO_READ set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], MMDIO out dx, ax ;Wait for the read bit to be cleared. mov ecx, 2048 ;limit .read: in ax, dx test ax, MDIO_READ jz @f dec ecx jnz .read @@: set_io [ebx + device.io_addr], MMRD in ax, dx and eax, 0xFFFF DEBUGF 1,"PHY read, val=0x%x\n", eax:4 ret endp ; Write a word data to PHY Chip align 4 proc phy_write stdcall, phy_addr:dword, reg:dword, val:dword DEBUGF 1,"PHY write, addr=0x%x reg=0x%x val=0x%x\n", \ [phy_addr]:8, [reg]:8, [val]:8 mov eax, [val] set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], MMWD out dx, ax ;Write the command to the MDIO bus mov eax, [phy_addr] shl eax, 8 add eax, [reg] add eax, MDIO_WRITE set_io [ebx + device.io_addr], MMDIO out dx, ax ;Wait for the write bit to be cleared. mov ecx, 2048 ;limit .write: in ax, dx test ax, MDIO_WRITE jz @f dec ecx jnz .write @@: DEBUGF 1,"PHY write ok\n" ret endp align 4 read_mac: DEBUGF 1,"Reading MAC:\n" mov cx, 3 lea edi, [ebx + device.mac] set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], MID_0L .mac: in ax, dx stosw inc dx inc dx dec cx jnz .mac DEBUGF 1,"%x-%x-%x-%x-%x-%x\n",\ [edi-6]:2, [edi-5]:2, [edi-4]:2, [edi-3]:2, [edi-2]:2, [edi-1]:2 ret ; End of code data fixups end data include '../peimport.inc' my_service db 'R6040',0 ; max 16 chars include zero include_debug_strings align 4 devices dd 0 device_list rd MAX_DEVICES ; This list contains all pointers to device structures the driver is handling