;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; Copyright (C) KolibriOS team 2004-2014. All rights reserved. ;; ;; Distributed under terms of the GNU General Public License ;; ;; ;; ;; i8255x (Intel eepro 100) driver for KolibriOS ;; ;; ;; ;; Written by hidnplayr@kolibrios.org ;; ;; ;; ;; GNU GENERAL PUBLIC LICENSE ;; ;; Version 2, June 1991 ;; ;; ;; ;; Some parts of this driver are based on the code of eepro100.c ;; ;; from linux. ;; ;; ;; ;; Intel's programming manual for i8255x: ;; ;; http://www.intel.com/design/network/manuals/8255x_opensdm.htm ;; ;; ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; TODO: use separate descriptors in memory instead of placing them in front of packets! format PE DLL native entry START CURRENT_API = 0x0200 COMPATIBLE_API = 0x0100 API_VERSION = (COMPATIBLE_API shl 16) + CURRENT_API MAX_DEVICES = 16 DEBUG = 1 __DEBUG__ = 1 __DEBUG_LEVEL__ = 2 ; 1 = verbose, 2 = errors only section '.flat' readable writable executable include '../proc32.inc' include '../struct.inc' include '../macros.inc' include '../fdo.inc' include '../netdrv.inc' ; Serial EEPROM EE_SK = 1 shl 0 ; serial clock EE_CS = 1 shl 1 ; chip select EE_DI = 1 shl 2 ; data in EE_DO = 1 shl 3 ; data out EE_MASK = EE_SK + EE_CS + EE_DI + EE_DO ; opcodes, first bit is start bit and must be 1 EE_READ = 110b EE_WRITE = 101b EE_ERASE = 111b ; The SCB accepts the following controls for the Tx and Rx units: CU_START = 0x0010 CU_RESUME = 0x0020 CU_STATSADDR = 0x0040 CU_SHOWSTATS = 0x0050 ; Dump statistics counters. CU_CMD_BASE = 0x0060 ; Base address to add CU commands. CU_DUMPSTATS = 0x0070 ; Dump then reset stats counters. RX_START = 0x0001 RX_RESUME = 0x0002 RX_ABORT = 0x0004 RX_ADDR_LOAD = 0x0006 RX_RESUMENR = 0x0007 INT_MASK = 0x0100 DRVR_INT = 0x0200 ; Driver generated interrupt CmdIASetup = 0x0001 CmdConfigure = 0x0002 CmdTx = 0x0004 CmdTxFlex = 0x0008 Cmdsuspend = 0x4000 reg_scb_status = 0 reg_scb_cmd = 2 reg_scb_ptr = 4 reg_port = 8 reg_eeprom = 14 reg_mdi_ctrl = 16 phy_100a = 0x000003E0 phy_100c = 0x035002A8 phy_82555_tx = 0x015002A8 phy_nsc_tx = 0x5C002000 phy_82562_et = 0x033002A8 phy_82562_em = 0x032002A8 phy_82562_ek = 0x031002A8 phy_82562_eh = 0x017002A8 phy_82552_v = 0xd061004d phy_unknown = 0xFFFFFFFF mac_82557_D100_A = 0 mac_82557_D100_B = 1 mac_82557_D100_C = 2 mac_82558_D101_A4 = 4 mac_82558_D101_B0 = 5 mac_82559_D101M = 8 mac_82559_D101S = 9 mac_82550_D102 = 12 mac_82550_D102_C = 13 mac_82551_E = 14 mac_82551_F = 15 mac_82551_10 = 16 mac_unknown = 0xFF struct rxfd status dw ? command dw ? link dd ? rx_buf_addr dd ? count dw ? size dw ? packet rb 1500 ends struc txfd { .status dw ? .command dw ? .link dd ? .desc_addr dd ? .count dd ? .buf_addr0 dd ? .buf_size0 dd ? } struc confcmd { .status dw ? .command dw ? .link dd ? .data rb 64 } struc lstats { .tx_good_frames dd ? .tx_coll16_errs dd ? .tx_late_colls dd ? .tx_underruns dd ? .tx_lost_carrier dd ? .tx_deferred dd ? .tx_one_colls dd ? .tx_multi_colls dd ? .tx_total_colls dd ? .rx_good_frames dd ? .rx_crc_errs dd ? .rx_align_errs dd ? .rx_resource_errs dd ? .rx_overrun_errs dd ? .rx_colls_errs dd ? .rx_runt_errs dd ? } struct device ETH_DEVICE io_addr dd ? pci_bus dd ? pci_dev dd ? rx_desc dd ? last_tx_buffer dd ? ee_bus_width db ? irq_line db ? rb 0x100 - ($ and 0xff) ; align 256 txfd txfd rb 0x100 - ($ and 0xff) ; align 256 confcmd confcmd rb 0x100 - ($ and 0xff) ; align 256 lstats lstats ends macro delay { push eax in ax, dx in ax, dx in ax, dx in ax, dx in ax, dx in ax, dx in ax, dx in ax, dx in ax, dx in ax, dx pop eax } ;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; proc START ;; ;; ;; ;; (standard driver proc) ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;; proc START c, state:dword cmp [state], 1 jne .exit .entry: DEBUGF 1,"Loading driver\n" invoke RegService, my_service, service_proc ret .fail: .exit: xor eax, eax ret endp ;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; proc SERVICE_PROC ;; ;; ;; ;; (standard driver proc) ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;; align 4 proc service_proc stdcall, ioctl:dword mov edx, [ioctl] mov eax, [edx + IOCTL.io_code] ;------------------------------------------------------ cmp eax, 0 ;SRV_GETVERSION jne @F cmp [edx + IOCTL.out_size], 4 jb .fail mov eax, [edx + IOCTL.output] mov [eax], dword API_VERSION xor eax, eax ret ;------------------------------------------------------ @@: cmp eax, 1 ;SRV_HOOK jne .fail cmp [edx + IOCTL.inp_size], 3 ; Data input must be at least 3 bytes jb .fail mov eax, [edx + IOCTL.input] cmp byte [eax], 1 ; 1 means device number and bus number (pci) are given jne .fail ; other types arent supported for this card yet ; check if the device is already listed mov esi, device_list mov ecx, [devices] test ecx, ecx jz .firstdevice ; mov eax, [edx + IOCTL.input] ; get the pci bus and device numbers mov ax , [eax+1] ; .nextdevice: mov ebx, [esi] cmp al, byte[ebx + device.pci_bus] jne @f cmp ah, byte[ebx + device.pci_dev] je .find_devicenum ; Device is already loaded, let's find it's device number @@: add esi, 4 loop .nextdevice ; This device doesnt have its own eth_device structure yet, lets create one .firstdevice: cmp [devices], MAX_DEVICES ; First check if the driver can handle one more card jae .fail allocate_and_clear ebx, sizeof.device, .fail ; Allocate the buffer for device structure ; Fill in the direct call addresses into the struct mov [ebx + device.reset], reset mov [ebx + device.transmit], transmit mov [ebx + device.unload], unload mov [ebx + device.name], my_service ; save the pci bus and device numbers mov eax, [edx + IOCTL.input] movzx ecx, byte[eax+1] mov [ebx + device.pci_bus], ecx movzx ecx, byte[eax+2] mov [ebx + device.pci_dev], ecx ; Now, it's time to find the base io addres of the PCI device stdcall PCI_find_io, [ebx + device.pci_bus], [ebx + device.pci_dev] mov [ebx + device.io_addr], eax ; We've found the io address, find IRQ now invoke PciRead8, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.interrupt_line mov [ebx + device.irq_line], al DEBUGF 1,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\ [ebx + device.pci_dev]:1,[ebx + device.pci_bus]:1,[ebx + device.irq_line]:1,[ebx + device.io_addr]:4 ; Ok, the eth_device structure is ready, let's probe the device pushf cli ; disable ints untilm initialisation is done call probe ; this function will output in eax test eax, eax jnz .err ; If an error occured, exit mov eax, [devices] ; Add the device structure to our device list mov [device_list+4*eax], ebx ; (IRQ handler uses this list to find device) inc [devices] ; popf mov [ebx + device.type], NET_TYPE_ETH invoke NetRegDev cmp eax, -1 je .err ret ; If the device was already loaded, find the device number and return it in eax .find_devicenum: DEBUGF 2,"Trying to find device number of already registered device\n" invoke NetPtrToNum ; This kernel procedure converts a pointer to device struct in ebx ; into a device number in edi mov eax, edi ; Application wants it in eax instead DEBUGF 2,"Kernel says: %u\n", eax ret ; If an error occured, remove all allocated data and exit (returning -1 in eax) .err: invoke KernelFree, ebx .fail: or eax, -1 ret ;------------------------------------------------------ endp ;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;; ;; ;; ;; Actual Hardware dependent code starts here ;; ;; ;; ;;/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\;; unload: ; TODO: (in this particular order) ; ; - Stop the device ; - Detach int handler ; - Remove device from local list (device_list) ; - call unregister function in kernel ; - Remove all allocated structures and buffers the card used or eax,-1 ret ;------------- ; ; Probe ; ;------------- align 4 probe: DEBUGF 1,"Probing\n" ; Make the device a bus master invoke PciRead32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command or al, PCI_CMD_MASTER invoke PciWrite32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command, eax ;--------------------------- ; First, identify the device invoke PciRead32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header.vendor_id ; get device/vendor id DEBUGF 1,"Vendor_id=0x%x\n", ax cmp ax, 0x8086 jne .notfound shr eax, 16 DEBUGF 1,"Device_id=0x%x\n", ax mov ecx, DEVICE_IDs mov edi, device_id_list repne scasw jne .notfound jmp .found .notfound: DEBUGF 2,"Unsupported device!\n" or eax, -1 ret .found: call ee_get_width call MAC_read_eeprom ;;; TODO: detect phy ;---------- ; ; Reset ; ;---------- align 4 reset: movzx eax, [ebx + device.irq_line] DEBUGF 1,"Attaching int handler to irq %x\n", eax:1 invoke AttachIntHandler, eax, int_handler, ebx test eax, eax jnz @f DEBUGF 2,"Could not attach int handler!\n" or eax, -1 ret @@: DEBUGF 1,"Resetting\n" ;--------------- ; reset the card set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_port xor eax, eax ; Software Reset out dx, eax mov esi, 10 invoke Sleep ; Give the card time to warm up. ;--------------------------------- ; Tell device where to store stats lea eax, [ebx + device.lstats.tx_good_frames] ; lstats invoke GetPhysAddr set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_scb_ptr out dx, eax mov ax, INT_MASK + CU_STATSADDR set_io [ebx + device.io_addr], reg_scb_cmd out dx, ax call cmd_wait ;----------------- ; setup RX set_io [ebx + device.io_addr], reg_scb_ptr xor eax, eax out dx, eax set_io [ebx + device.io_addr], reg_scb_cmd mov ax, INT_MASK + RX_ADDR_LOAD out dx, ax call cmd_wait ;----------------------------- ; Create RX and TX descriptors call create_ring ; RX start set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_scb_ptr mov eax, [ebx + device.rx_desc] invoke GetPhysAddr out dx, eax mov ax, INT_MASK + RX_START set_io [ebx + device.io_addr], reg_scb_cmd out dx, ax call cmd_wait ; Set-up TX set_io [ebx + device.io_addr], reg_scb_ptr xor eax, eax out dx, eax set_io [ebx + device.io_addr], reg_scb_cmd mov ax, INT_MASK + CU_CMD_BASE out dx, ax call cmd_wait ; -------------------- mov [ebx + device.confcmd.command], CmdConfigure + Cmdsuspend mov [ebx + device.confcmd.status], 0 lea eax, [ebx + device.txfd.status] invoke GetPhysAddr mov [ebx + device.confcmd.link], eax mov esi, confcmd_data lea edi, [ebx + device.confcmd.data] mov ecx, 22 rep movsb mov byte[ebx + device.confcmd.data + 1], 0x88 ; fifo of 8 each mov byte[ebx + device.confcmd.data + 4], 0 mov byte[ebx + device.confcmd.data + 5], 0x80 mov byte[ebx + device.confcmd.data + 15], 0x48 mov byte[ebx + device.confcmd.data + 19], 0x80 mov byte[ebx + device.confcmd.data + 21], 0x05 mov [ebx + device.txfd.command], CmdIASetup mov [ebx + device.txfd.status], 0 lea eax, [ebx + device.confcmd.status] invoke GetPhysAddr mov [ebx + device.txfd.link], eax ;;; copy in our MAC lea edi, [ebx + device.txfd.desc_addr] lea esi, [ebx + device.mac] movsd movsw set_io [ebx + device.io_addr], reg_scb_ptr lea eax, [ebx + device.txfd.status] invoke GetPhysAddr out dx, eax ; Start CU & enable ints set_io [ebx + device.io_addr], reg_scb_cmd mov ax, CU_START out dx, ax call cmd_wait ;----------------------- ; build txfd structure (again!) lea eax, [ebx + device.txfd.status] invoke GetPhysAddr mov [ebx + device.txfd.link], eax mov [ebx + device.txfd.count], 0x02208000 lea eax, [ebx + device.txfd.buf_addr0] invoke GetPhysAddr mov [ebx + device.txfd.desc_addr], eax ; Indicate that we have successfully reset the card DEBUGF 1,"Reset complete\n" mov [ebx + device.mtu], 1514 ; Set link state to unknown mov [ebx + device.state], ETH_LINK_UNKNOWN xor eax, eax ; indicate that we have successfully reset the card ret align 4 create_ring: DEBUGF 1,"Creating ring\n" ;--------------------- ; build rxfd structure invoke KernelAlloc, 2000 mov [ebx + device.rx_desc], eax mov esi, eax invoke GetPhysAddr mov [esi + rxfd.status], 0x0000 mov [esi + rxfd.command], 0x0000 mov [esi + rxfd.link], eax mov [esi + rxfd.count], 0 mov [esi + rxfd.size], 1528 ;----------------------- ; build txfd structure lea eax, [ebx + device.txfd.status] invoke GetPhysAddr mov [ebx + device.txfd.link], eax mov [ebx + device.txfd.count], 0x02208000 lea eax, [ebx + device.txfd.buf_addr0] invoke GetPhysAddr mov [ebx + device.txfd.desc_addr], eax ret ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; Transmit ;; ;; ;; ;; In: pointer to device structure in ebx ;; ;; ;; ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; proc transmit stdcall bufferptr, buffersize pushf cli DEBUGF 1,"Transmitting packet, buffer:%x, size:%u\n", [bufferptr], [buffersize] mov eax, [bufferptr] DEBUGF 1,"To: %x-%x-%x-%x-%x-%x From: %x-%x-%x-%x-%x-%x Type:%x%x\n",\ [eax+00]:2,[eax+01]:2,[eax+02]:2,[eax+03]:2,[eax+04]:2,[eax+05]:2,\ [eax+06]:2,[eax+07]:2,[eax+08]:2,[eax+09]:2,[eax+10]:2,[eax+11]:2,\ [eax+13]:2,[eax+12]:2 cmp [buffersize], 1514 ja .fail cmp [buffersize], 60 jb .fail ;;; TODO: check if current descriptor is in use ; fill in buffer address and size mov [ebx + device.last_tx_buffer], eax invoke GetPhysAddr mov [ebx + device.txfd.buf_addr0], eax mov ecx, [buffersize] mov [ebx + device.txfd.buf_size0], ecx mov [ebx + device.txfd.status], 0 mov [ebx + device.txfd.command], Cmdsuspend + CmdTx + CmdTxFlex + 1 shl 15 ;;; EL bit ; mov [txfd.count], 0x02208000 ;;;;;;;;;;; ; Inform device of the new/updated transmit descriptor lea eax, [ebx + device.txfd.status] invoke GetPhysAddr set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_scb_ptr out dx, eax ; Start the transmit mov ax, CU_START set_io [ebx + device.io_addr], reg_scb_cmd out dx, ax call cmd_wait ; Update stats inc [ebx + device.packets_tx] mov ecx, [buffersize] add dword[ebx + device.bytes_tx], ecx adc dword[ebx + device.bytes_tx + 4], 0 DEBUGF 1,"Transmit OK\n" popf xor eax, eax ret .fail: invoke KernelFree, [bufferptr] popf or eax, -1 ret endp ;;;;;;;;;;;;;;;;;;;;;;; ;; ;; ;; Interrupt handler ;; ;; ;; ;;;;;;;;;;;;;;;;;;;;;;; align 4 int_handler: push ebx esi edi DEBUGF 1,"INT\n" ; find pointer of device wich made IRQ occur mov ecx, [devices] test ecx, ecx jz .nothing mov esi, device_list .nextdevice: mov ebx, [esi] ; set_io [ebx + device.io_addr], 0 ; reg_scb_status = 0 set_io [ebx + device.io_addr], reg_scb_status in ax, dx out dx, ax ; send it back to ACK test ax, ax jnz .got_it .continue: add esi, 4 dec ecx jnz .nextdevice .nothing: pop edi esi ebx xor eax, eax ret ; If no device was found, abort (The irq was probably for a device, not registered to this driver) .got_it: DEBUGF 1,"Device: %x Status: %x\n", ebx, ax test ax, 1 shl 14 ; did we receive a frame? jz .no_rx push ax DEBUGF 1,"Receiving\n" push ebx .rx_loop: pop ebx mov esi, [ebx + device.rx_desc] cmp [esi + rxfd.status], 0 ; we could also check bits C and OK (bit 15 and 13) je .nodata DEBUGF 1,"rxfd status=0x%x\n", [esi + rxfd.status]:4 movzx ecx, [esi + rxfd.count] and ecx, 0x3fff push ebx push .rx_loop push ecx add esi, rxfd.packet push esi ; Update stats add dword [ebx + device.bytes_rx], ecx adc dword [ebx + device.bytes_rx + 4], 0 inc dword [ebx + device.packets_rx] ; allocate new descriptor invoke KernelAlloc, 2000 mov [ebx + device.rx_desc], eax mov esi, eax invoke GetPhysAddr mov [esi + rxfd.status], 0x0000 mov [esi + rxfd.command], 0xc000 ; End of list + Suspend mov [esi + rxfd.link], eax mov [esi + rxfd.count], 0 mov [esi + rxfd.size], 1528 ; restart RX set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_scb_ptr ; lea eax, [ebx + device.rx_desc] ; invoke GetPhysAddr out dx, eax set_io [ebx + device.io_addr], reg_scb_cmd mov ax, RX_START out dx, ax call cmd_wait ; And give packet to kernel jmp [Eth_input] .nodata: DEBUGF 1, "no more data\n" pop ax .no_rx: ; Cleanup after TX cmp [ebx + device.txfd.status], 0 je .done cmp [ebx + device.last_tx_buffer], 0 je .done push ax DEBUGF 1, "Removing packet 0x%x from RAM!\n", [ebx + device.last_tx_buffer] invoke KernelFree, [ebx + device.last_tx_buffer] mov [ebx + device.last_tx_buffer], 0 pop ax .done: and ax, 00111100b cmp ax, 00001000b jne .fail DEBUGF 1, "out of resources!\n" ; Restart the RX ; allocate new descriptor invoke KernelAlloc, 2000 mov [ebx + device.rx_desc], eax mov esi, eax invoke GetPhysAddr mov [esi + rxfd.status], 0x0000 mov [esi + rxfd.command], 0xc000 ; End of list + Suspend mov [esi + rxfd.link], eax mov [esi + rxfd.count], 0 mov [esi + rxfd.size], 1528 ; restart RX set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_scb_ptr ; lea eax, [ebx + device.rx_desc] ; invoke GetPhysAddr out dx, eax set_io [ebx + device.io_addr], reg_scb_cmd mov ax, RX_START out dx, ax call cmd_wait .fail: pop edi esi ebx xor eax, eax inc eax ret align 4 cmd_wait: in al, dx test al, al jnz cmd_wait ret align 4 ee_read: ; esi = address to read DEBUGF 1,"Eeprom read from 0x%x\n", esi set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_eeprom ;----------------------------------------------------- ; Prepend start bit + read opcode to the address field ; and shift it to the very left bits of esi mov cl, 29 sub cl, [ebx + device.ee_bus_width] shl esi, cl or esi, EE_READ shl 29 movzx ecx, [ebx + device.ee_bus_width] add ecx, 3 mov al, EE_CS out dx, al delay ;----------------------- ; Write this to the chip .loop: mov al, EE_CS + EE_SK shl esi, 1 jnc @f or al, EE_DI @@: out dx, al delay and al, not EE_SK out dx, al delay loop .loop ;------------------------------ ; Now read the data from eeprom xor esi, esi mov ecx, 16 .loop2: shl esi, 1 mov al, EE_CS + EE_SK out dx, al delay in al, dx test al, EE_DO jz @f inc esi @@: mov al, EE_CS out dx, al delay loop .loop2 ;----------------------- ; de-activate the eeprom xor ax, ax out dx, ax DEBUGF 1,"0x%x\n", esi:4 ret align 4 ee_write: ; esi = address to write to, di = data DEBUGF 1,"Eeprom write 0x%x to 0x%x\n", di, esi set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_eeprom ;----------------------------------------------------- ; Prepend start bit + write opcode to the address field ; and shift it to the very left bits of esi mov cl, 29 sub cl, [ebx + device.ee_bus_width] shl esi, cl or esi, EE_WRITE shl 29 movzx ecx, [ebx + device.ee_bus_width] add ecx, 3 mov al, EE_CS ; enable chip out dx, al ;----------------------- ; Write this to the chip .loop: mov al, EE_CS + EE_SK shl esi, 1 jnc @f or al, EE_DI @@: out dx, al delay and al, not EE_SK out dx, al delay loop .loop ;----------------------------- ; Now write the data to eeprom mov ecx, 16 .loop2: mov al, EE_CS + EE_SK shl di, 1 jnc @f or al, EE_DI @@: out dx, al delay and al, not EE_SK out dx, al delay loop .loop2 ;----------------------- ; de-activate the eeprom xor al, al out dx, al ret align 4 ee_get_width: set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_eeprom mov al, EE_CS ; activate eeprom out dx, al delay mov si, EE_READ shl 13 xor ecx, ecx .loop: mov al, EE_CS + EE_SK shl si, 1 jnc @f or al, EE_DI @@: out dx, al delay and al, not EE_SK out dx, al delay inc ecx cmp ecx, 15 jae .give_up in al, dx test al, EE_DO jnz .loop xor al, al out dx, al ; de-activate eeprom sub cl, 3 ; dont count the opcode bits mov [ebx + device.ee_bus_width], cl DEBUGF 1, "Eeprom width=%u bit\n", ecx ret .give_up: DEBUGF 2, "Eeprom not found!\n" xor al, al out dx, al ; de-activate eeprom ret ; cx = phy addr ; dx = phy reg addr ; ax = data align 4 mdio_read: DEBUGF 1,"MDIO read\n" shl ecx, 21 ; PHY addr shl edx, 16 ; PHY reg addr mov eax, ecx or eax, edx or eax, 10b shl 26 ; read opcode set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_mdi_ctrl out dx, eax .wait: delay in eax, dx test eax, 1 shl 28 ; ready bit jz .wait ret ; ax = data ; cx = phy addr ; dx = phy reg addr ; ax = data align 4 mdio_write: DEBUGF 1,"MDIO write\n" and eax, 0xffff shl ecx, 21 ; PHY addr shl edx, 16 ; PHY reg addr or eax, ecx or eax, edx or eax, 01b shl 26 ; write opcode set_io [ebx + device.io_addr], 0 set_io [ebx + device.io_addr], reg_mdi_ctrl out dx, eax .wait: delay in eax, dx test eax, 1 shl 28 ; ready bit jz .wait ret read_mac: ret align 4 MAC_read_eeprom: mov esi, 0 call ee_read mov word[ebx + device.mac], si mov esi, 1 call ee_read mov word[ebx + device.mac+2], si mov esi, 2 call ee_read mov word[ebx + device.mac+4], si ret align 4 MAC_write: ;;;; ret ; End of code data fixups end data include '../peimport.inc' my_service db 'I8255X', 0 ; max 16 chars include zero devicename db 'Intel Etherexpress pro/100', 0 confcmd_data db 22, 0x08, 0, 0, 0, 0x80, 0x32, 0x03, 1 db 0, 0x2e, 0, 0x60, 0, 0xf2, 0x48, 0, 0x40, 0xf2 db 0x80, 0x3f, 0x05 ; 22 bytes total device_id_list: dw 0x1029 dw 0x1030 dw 0x1031 dw 0x1032 dw 0x1033 dw 0x1034 dw 0x1038 dw 0x1039 dw 0x103A dw 0x103B dw 0x103C dw 0x103D dw 0x103E dw 0x1050 dw 0x1051 dw 0x1052 dw 0x1053 dw 0x1054 dw 0x1055 dw 0x1056 dw 0x1057 dw 0x1059 dw 0x1064 dw 0x1065 dw 0x1066 dw 0x1067 dw 0x1068 dw 0x1069 dw 0x106A dw 0x106B dw 0x1091 dw 0x1092 dw 0x1093 dw 0x1094 dw 0x1095 dw 0x10fe dw 0x1209 dw 0x1229 dw 0x2449 dw 0x2459 dw 0x245D dw 0x27DC DEVICE_IDs = ($ - device_id_list) / 2 include_debug_strings ; All data wich FDO uses will be included here align 4 devices dd 0 ; number of currently running devices device_list rd MAX_DEVICES ; This list contains all pointers to device structures the driver is handling