kolibrios/kernel/branches/kolibri-process/bus/usb/protocol.inc
Sergey Semyonov (Serge) 15fd6b2c81 kolibri-process: update
git-svn-id: svn://kolibrios.org@4587 a494cfbc-eb01-0410-851d-a64ba20cac60
2014-02-22 11:39:11 +00:00

1010 lines
43 KiB
PHP

; Implementation of the USB protocol for device enumeration.
; Manage a USB device when it becomes ready for USB commands:
; configure, enumerate, load the corresponding driver(s),
; pass device information to the driver.
; =============================================================================
; ================================= Constants =================================
; =============================================================================
; USB standard request codes
USB_GET_STATUS = 0
USB_CLEAR_FEATURE = 1
USB_SET_FEATURE = 3
USB_SET_ADDRESS = 5
USB_GET_DESCRIPTOR = 6
USB_SET_DESCRIPTOR = 7
USB_GET_CONFIGURATION = 8
USB_SET_CONFIGURATION = 9
USB_GET_INTERFACE = 10
USB_SET_INTERFACE = 11
USB_SYNCH_FRAME = 12
; USB standard descriptor types
USB_DEVICE_DESCR = 1
USB_CONFIG_DESCR = 2
USB_STRING_DESCR = 3
USB_INTERFACE_DESCR = 4
USB_ENDPOINT_DESCR = 5
USB_DEVICE_QUALIFIER_DESCR = 6
USB_OTHER_SPEED_CONFIG_DESCR = 7
USB_INTERFACE_POWER_DESCR = 8
; Compile-time setting. If set, the code will dump all descriptors as they are
; read to the debug board.
USB_DUMP_DESCRIPTORS = 1
; According to the USB specification (9.2.6.3),
; any device must response to SET_ADDRESS in 50 ms, or 5 timer ticks.
; Of course, our world is far from ideal.
; I have seen devices that just NAK everything when being reset from working
; state, but start to work after second reset.
; Our strategy is as follows: give 2 seconds for the first attempt,
; this should be enough for normal devices and not too long to detect buggy ones.
; If the device continues NAKing, reset it and retry several times,
; doubling the interval: 2s -> 4s -> 8s -> 16s. Give up after that.
; Numbers are quite arbitrary.
TIMEOUT_SET_ADDRESS_INITIAL = 200
TIMEOUT_SET_ADDRESS_LAST = 1600
; =============================================================================
; ================================ Structures =================================
; =============================================================================
; USB descriptors. See USB specification for detailed explanations.
; First two bytes of every descriptor have the same meaning.
struct usb_descr
bLength db ?
; Size of this descriptor in bytes
bDescriptorType db ?
; One of USB_*_DESCR constants.
ends
; USB device descriptor
struct usb_device_descr usb_descr
bcdUSB dw ?
; USB Specification Release number in BCD, e.g. 110h = USB 1.1
bDeviceClass db ?
; USB Device Class Code
bDeviceSubClass db ?
; USB Device Subclass Code
bDeviceProtocol db ?
; USB Device Protocol Code
bMaxPacketSize0 db ?
; Maximum packet size for zero endpoint
idVendor dw ?
; Vendor ID
idProduct dw ?
; Product ID
bcdDevice dw ?
; Device release number in BCD
iManufacturer db ?
; Index of string descriptor describing manufacturer
iProduct db ?
; Index of string descriptor describing product
iSerialNumber db ?
; Index of string descriptor describing serial number
bNumConfigurations db ?
; Number of possible configurations
ends
; USB configuration descriptor
struct usb_config_descr usb_descr
wTotalLength dw ?
; Total length of data returned for this configuration
bNumInterfaces db ?
; Number of interfaces in this configuration
bConfigurationValue db ?
; Value for SET_CONFIGURATION control request
iConfiguration db ?
; Index of string descriptor describing this configuration
bmAttributes db ?
; Bit 6 is SelfPowered, bit 5 is RemoteWakeupSupported,
; bit 7 must be 1, other bits must be 0
bMaxPower db ?
; Maximum power consumption from the bus in 2mA units
ends
; USB interface descriptor
struct usb_interface_descr usb_descr
; The following two fields work in pair. Sometimes one interface can work
; in different modes; e.g. videostream from web-cameras requires different
; bandwidth depending on resolution/quality/compression settings.
; Each mode of each interface has its own descriptor with its own endpoints
; following; all descriptors for one interface have the same bInterfaceNumber,
; and different bAlternateSetting.
; By default, any interface operates in mode with bAlternateSetting = 0.
; Often this is the only mode. If there are another modes, the active mode
; is selected by SET_INTERFACE(bAlternateSetting) control request.
bInterfaceNumber db ?
bAlternateSetting db ?
bNumEndpoints db ?
; Number of endpoints used by this interface, excluding zero endpoint
bInterfaceClass db ?
; USB Interface Class Code
bInterfaceSubClass db ?
; USB Interface Subclass Code
bInterfaceProtocol db ?
; USB Interface Protocol Code
iInterface db ?
; Index of string descriptor describing this interface
ends
; USB endpoint descriptor
struct usb_endpoint_descr usb_descr
bEndpointAddress db ?
; Lower 4 bits form endpoint number,
; upper bit is 0 for OUT endpoints and 1 for IN endpoints,
; other bits must be zero
bmAttributes db ?
; Lower 2 bits form transfer type, one of *_PIPE,
; other bits must be zero for non-isochronous endpoints;
; refer to the USB specification for meaning in isochronous case
wMaxPacketSize dw ?
; Lower 11 bits form maximum packet size,
; next two bits specify the number of additional transactions per microframe
; for high-speed periodic endpoints, other bits must be zero.
bInterval db ?
; Interval for polling endpoint for data transfers.
; Isochronous and high-speed interrupt endpoints: poll every 2^(bInterval-1)
; (micro)frames
; Full/low-speed interrupt endpoints: poll every bInterval frames
; High-speed bulk/control OUT endpoints: maximum NAK rate
ends
; =============================================================================
; =================================== Code ====================================
; =============================================================================
; When a new device is ready to be configured, a controller-specific code
; calls usb_new_device.
; The sequence of further actions:
; * open pipe for the zero endpoint (usb_new_device);
; maximum packet size is not known yet, but it must be at least 8 bytes,
; so it is safe to send packets with <= 8 bytes
; * issue SET_ADDRESS control request (usb_new_device)
; * set the new device address in the pipe (usb_set_address_callback)
; * notify a controller-specific code that initialization of other ports
; can be started (usb_set_address_callback)
; * issue GET_DESCRIPTOR control request for first 8 bytes of device descriptor
; (usb_after_set_address)
; * first 8 bytes of device descriptor contain the true packet size for zero
; endpoint, so set the true packet size (usb_get_descr8_callback)
; * first 8 bytes of a descriptor contain the full size of this descriptor,
; issue GET_DESCRIPTOR control request for the full device descriptor
; (usb_after_set_endpoint_size)
; * issue GET_DESCRIPTOR control request for first 8 bytes of configuration
; descriptor (usb_get_descr_callback)
; * issue GET_DESCRIPTOR control request for full configuration descriptor
; (usb_know_length_callback)
; * issue SET_CONFIGURATION control request (usb_set_config_callback)
; * parse configuration descriptor, load the corresponding driver(s),
; pass the configuration descriptor to the driver and let the driver do
; the further work (usb_got_config_callback)
; This function is called from controller-specific part
; when a new device is ready to be configured.
; in: ecx -> pseudo-pipe, part of usb_pipe
; in: esi -> usb_controller
; in: [esi+usb_controller.ResettingHub] is the pointer to usb_hub for device,
; NULL if the device is connected to the root hub
; in: [esi+usb_controller.ResettingPort] is the port for the device, zero-based
; in: [esi+usb_controller.ResettingSpeed] is the speed of the device, one of
; USB_SPEED_xx.
; out: eax = 0 <=> failed, the caller should disable the port.
proc usb_new_device
push ebx edi ; save used registers to be stdcall
; 1. Check whether we're here because we were trying to reset
; already-registered device in hope to fix something serious.
; If so, skip allocation and go to 6.
movzx eax, [esi+usb_controller.ResettingPort]
mov edx, [esi+usb_controller.ResettingHub]
test edx, edx
jz .test_roothub
mov edx, [edx+usb_hub.ConnectedDevicesPtr]
mov ebx, [edx+eax*4]
jmp @f
.test_roothub:
mov ebx, [esi+usb_controller.DevicesByPort+eax*4]
@@:
test ebx, ebx
jnz .try_set_address
; 2. Allocate resources. Any device uses the following resources:
; - device address in the bus
; - memory for device data
; - pipe for zero endpoint
; If some allocation fails, we must undo our actions. Closing the pipe
; is a hard task, so we avoid it and open the pipe as the last resource.
; The order for other two allocations is quite arbitrary.
; 2a. Allocate a bus address.
push ecx
call usb_set_address_request
pop ecx
; 2b. If failed, just return zero.
test eax, eax
jz .nothing
; 2c. Allocate memory for device data.
; For now, we need sizeof.usb_device_data and extra 8 bytes for GET_DESCRIPTOR
; input and output, see usb_after_set_address. Later we will reallocate it
; to actual size needed for descriptors.
movi eax, sizeof.usb_device_data + 8
push ecx
call malloc
pop ecx
; 2d. If failed, free the bus address and return zero.
test eax, eax
jz .nomemory
; 2e. Open pipe for endpoint zero.
; For now, we do not know the actual maximum packet size;
; for full-speed devices it can be any of 8, 16, 32, 64 bytes,
; low-speed devices must have 8 bytes, high-speed devices must have 64 bytes.
; Thus, we must use some fake "maximum packet size" until the actual size
; will be known. However, the maximum packet size must be at least 8, and
; initial stages of the configuration process involves only packets of <= 8
; bytes, they will be transferred correctly as long as
; the fake "maximum packet size" is also at least 8.
; Thus, any number >= 8 is suitable for actual hardware.
; However, software emulation of EHCI in VirtualBox assumes that high-speed
; control transfers are those originating from pipes with max packet size = 64,
; even on early stages of the configuration process. This is incorrect,
; but we have no specific preferences, so let VirtualBox be happy and use 64
; as the fake "maximum packet size".
push eax
; We will need many zeroes.
; "push edi" is one byte, "push 0" is two bytes; save space, use edi.
xor edi, edi
stdcall usb_open_pipe, ecx, edi, 64, edi, edi
; Put pointer to pipe into ebx. "xchg eax,reg" is one byte, mov is two bytes.
xchg eax, ebx
pop eax
; 2f. If failed, free the memory, the bus address and return zero.
test ebx, ebx
jz .freememory
; 3. Store pointer to device data in the pipe structure.
mov [ebx+usb_pipe.DeviceData], eax
; 4. Init device data, using usb_controller.Resetting* variables.
mov [eax+usb_device_data.Timer], edi
mov dword [eax+usb_device_data.DeviceDescriptor], TIMEOUT_SET_ADDRESS_INITIAL
mov [eax+usb_device_data.TTHub], edi
mov [eax+usb_device_data.TTPort], 0
mov [eax+usb_device_data.NumInterfaces], edi
mov [eax+usb_device_data.DeviceDescrSize], 0
mov dl, [esi+usb_controller.ResettingSpeed]
mov [eax+usb_device_data.Speed], dl
mov [eax+usb_device_data.NumPipes], 1
push ebx
cmp dl, USB_SPEED_HS
jz .nott
mov ebx, [esi+usb_controller.ResettingHub]
test ebx, ebx
jz .nott
mov cl, [esi+usb_controller.ResettingPort]
mov edx, [ebx+usb_hub.ConfigPipe]
mov edx, [edx+usb_pipe.DeviceData]
cmp [edx+usb_device_data.TTHub], 0
jz @f
mov cl, [edx+usb_device_data.TTPort]
mov ebx, [edx+usb_device_data.TTHub]
jmp .has_tt
@@:
cmp [edx+usb_device_data.Speed], USB_SPEED_HS
jnz .nott
.has_tt:
mov [eax+usb_device_data.TTHub], ebx
mov [eax+usb_device_data.TTPort], cl
.nott:
pop ebx
mov [eax+usb_device_data.ConfigDataSize], edi
mov [eax+usb_device_data.Interfaces], edi
movzx ecx, [esi+usb_controller.ResettingPort]
mov [eax+usb_device_data.Port], cl
mov edx, [esi+usb_controller.ResettingHub]
mov [eax+usb_device_data.Hub], edx
; 5. Store pointer to the config pipe in the hub data.
; Config pipe serves as device identifier.
; Root hubs use the array inside usb_controller structure,
; non-root hubs use the array immediately after usb_hub structure.
test edx, edx
jz .roothub
mov edx, [edx+usb_hub.ConnectedDevicesPtr]
mov [edx+ecx*4], ebx
jmp @f
.roothub:
mov [esi+usb_controller.DevicesByPort+ecx*4], ebx
@@:
call usb_reinit_pipe_list
; 6. Issue SET_ADDRESS control request, using buffer filled in step 2a.
; 6a. Configure timer to force reset after timeout.
; Note: we can't use self-destructing timer, because we need to be able to cancel it,
; and for self-destructing timer we could have race condition in cancelling/destructing.
; DEBUGF 1,'K : pipe %x\n',ebx
.try_set_address:
xor edi, edi
mov edx, [ebx+usb_pipe.DeviceData]
stdcall timer_hs, [edx+usb_device_data.DeviceDescriptor], 7FFFFFFFh, usb_abort_pipe, ebx
test eax, eax
jz .nothing
mov edx, [ebx+usb_pipe.DeviceData]
mov [edx+usb_device_data.Timer], eax
; 6b. If it succeeded, setup timer to configure wait timeout.
lea eax, [esi+usb_controller.SetAddressBuffer]
stdcall usb_control_async, ebx, eax, edi, edi, usb_set_address_callback, edi, edi
; Use the return value from usb_control_async as our return value;
; if it is zero, then something has failed.
.nothing:
; 7. Return.
pop edi ebx ; restore used registers to be stdcall
ret
; Handlers of failures in steps 2b, 2d, 2f.
.freememory:
call free
jmp .freeaddr
.nomemory:
dbgstr 'No memory for device data'
.freeaddr:
mov ecx, dword [esi+usb_controller.SetAddressBuffer+2]
bts [esi+usb_controller.ExistingAddresses], ecx
xor eax, eax
jmp .nothing
endp
; Helper procedure for usb_new_device.
; Allocates a new USB address and fills usb_controller.SetAddressBuffer
; with data for SET_ADDRESS(allocated_address) request.
; out: eax = 0 <=> failed
; Destroys edi.
proc usb_set_address_request
; There are 128 bits, one for each possible address.
; Note: only the USB thread works with usb_controller.ExistingAddresses,
; so there is no need for synchronization.
; We must find a bit set to 1 and clear it.
; 1. Find the first dword which has a nonzero bit = which is nonzero.
mov ecx, 128/32
lea edi, [esi+usb_controller.ExistingAddresses]
xor eax, eax
repz scasd
; 2. If all dwords are zero, return an error.
jz .error
; 3. The dword at [edi-4] is nonzero. Find the lowest nonzero bit.
bsf eax, [edi-4]
; Now eax = bit number inside the dword at [edi-4].
; 4. Clear the bit.
btr [edi-4], eax
; 5. Generate the address by edi = memory address and eax = bit inside dword.
; Address = eax + 8 * (edi-4 - (esi+usb_controller.ExistingAddress)).
sub edi, esi
lea edi, [eax+(edi-4-usb_controller.ExistingAddresses)*8]
; 6. Store the allocated address in SetAddressBuffer and fill remaining fields.
; Note that usb_controller is zeroed at allocation, so only command byte needs
; to be filled.
mov byte [esi+usb_controller.SetAddressBuffer+1], USB_SET_ADDRESS
mov dword [esi+usb_controller.SetAddressBuffer+2], edi
; 7. Return non-zero value in eax.
inc eax
.nothing:
ret
.error:
dbgstr 'cannot allocate USB address'
xor eax, eax
jmp .nothing
endp
; This procedure is called by USB stack when SET_ADDRESS request initiated by
; usb_new_device is completed, either successfully or unsuccessfully.
; Note that USB stack uses esi = pointer to usb_controller.
proc usb_set_address_callback stdcall, pipe:dword, status:dword, buffer:dword, length:dword, calldata:dword
push ebx ; save ebx to be stdcall
mov ebx, [pipe]
; 1. In any case, cancel the timer.
mov eax, [ebx+usb_pipe.DeviceData]
stdcall cancel_timer_hs, [eax+usb_device_data.Timer]
mov eax, [ebx+usb_pipe.DeviceData]
mov [eax+usb_device_data.Timer], 0
; Load data to registers for further references.
mov ecx, dword [esi+usb_controller.SetAddressBuffer+2]
mov eax, [esi+usb_controller.HardwareFunc]
; 2. Check whether the device has accepted new address. If so, proceed to 3.
; Otherwise, go to 4 if killed by usb_set_address_timeout or to 5 otherwise.
cmp [status], USB_STATUS_CANCELLED
jz .timeout
cmp [status], 0
jnz .error
; 3. Address accepted.
; 3a. The controller-specific structure for the control pipe still uses
; zero address. Call the controller-specific function to change it to
; the actual address.
; Note that the hardware could cache the controller-specific structure,
; so setting the address could take some time until the cache is evicted.
; Thus, the call is asynchronous; meet us in usb_after_set_address when it will
; be safe to continue.
; dbgstr 'address set in device'
call [eax+usb_hardware_func.SetDeviceAddress]
; 3b. If the port is in non-root hub, clear 'reset in progress' flag.
; In any case, proceed to 6.
mov eax, [esi+usb_controller.ResettingHub]
test eax, eax
jz .return
and [eax+usb_hub.Actions], not HUB_RESET_IN_PROGRESS
.return:
; 6. Address configuration done, we can proceed with other ports.
; Call the worker function for that.
call usb_test_pending_port
.wakeup:
push esi edi
call usb_wakeup
pop edi esi
.nothing:
pop ebx ; restore ebx to be stdcall
ret
.timeout:
; 4. Device continues to NAK the request. Reset it and retry.
mov edx, [ebx+usb_pipe.DeviceData]
mov ecx, [edx+usb_device_data.DeviceDescriptor]
add ecx, ecx
cmp ecx, TIMEOUT_SET_ADDRESS_LAST
ja .error
mov [edx+usb_device_data.DeviceDescriptor], ecx
dbgstr 'Timeout in USB device initialization, trying to reset...'
cmp [esi+usb_controller.ResettingHub], 0
jz .reset_roothub
push esi
mov esi, [esi+usb_controller.ResettingHub]
call usb_hub_initiate_reset
pop esi
jmp .nothing
.reset_roothub:
movzx ecx, [esi+usb_controller.ResettingPort]
call [eax+usb_hardware_func.InitiateReset]
jmp .wakeup
.error:
; 5. Device error: device not responding, disconnect etc.
DEBUGF 1,'K : error %d in SET_ADDRESS, USB device disabled\n',[status]
; 5a. The address has not been accepted. Mark it as free.
bts dword [esi+usb_controller.ExistingAddresses], ecx
; 5b. Disable the port with bad device.
; For the root hub, call the controller-specific function and go to 6.
; For non-root hubs, let the hub code do its work and return (the request
; could take some time, the hub code is responsible for proceeding).
cmp [esi+usb_controller.ResettingHub], 0
jz .roothub
mov eax, [esi+usb_controller.ResettingHub]
call usb_hub_disable_resetting_port
jmp .nothing
.roothub:
movzx ecx, [esi+usb_controller.ResettingPort]
call [eax+usb_hardware_func.PortDisable]
jmp .return
endp
; This procedure is called from usb_subscription_done when the hardware cache
; is cleared after request from usb_set_address_callback.
; in: ebx -> usb_pipe
proc usb_after_set_address
; dbgstr 'address set for controller'
; Issue control transfer GET_DESCRIPTOR(DEVICE_DESCR) for first 8 bytes.
; Remember, we still do not know the actual packet size;
; 8-bytes-request is safe.
; usb_new_device has allocated 8 extra bytes besides sizeof.usb_device_data;
; use them for both input and output.
mov eax, [ebx+usb_pipe.DeviceData]
add eax, usb_device_data.DeviceDescriptor
mov dword [eax], \
80h + \ ; device-to-host, standard, device-wide
(USB_GET_DESCRIPTOR shl 8) + \ ; request
(0 shl 16) + \ ; descriptor index: there is only one
(USB_DEVICE_DESCR shl 24) ; descriptor type
mov dword [eax+4], 8 shl 16 ; data length
stdcall usb_control_async, ebx, eax, eax, 8, usb_get_descr8_callback, eax, 0
ret
endp
; This procedure is called by USB stack when GET_DESCRIPTOR(DEVICE_DESCR)
; request initiated by usb_after_set_address is completed, either successfully
; or unsuccessfully.
; Note that USB stack uses esi = pointer to usb_controller.
proc usb_get_descr8_callback stdcall, pipe:dword, status:dword, buffer:dword, length:dword, calldata:dword
; mov eax, [buffer]
; DEBUGF 1,'K : descr8: l=%x; %x %x %x %x %x %x %x %x\n',[length],\
; [eax]:2,[eax+1]:2,[eax+2]:2,[eax+3]:2,[eax+4]:2,[eax+5]:2,[eax+6]:2,[eax+7]:2
push edi ebx ; save used registers to be stdcall
mov ebx, [pipe]
; 1. Check whether the operation was successful.
; If not, say something to the debug board and stop the initialization.
cmp [status], 0
jnz .error
; 2. Length of descriptor must be at least sizeof.usb_device_descr bytes.
; If not, say something to the debug board and stop the initialization.
mov eax, [ebx+usb_pipe.DeviceData]
cmp [eax+usb_device_data.DeviceDescriptor+usb_device_descr.bLength], sizeof.usb_device_descr
jb .error
; 3. Now first 8 bytes of device descriptor are known;
; set DeviceDescrSize accordingly.
mov [eax+usb_device_data.DeviceDescrSize], 8
; 4. The controller-specific structure for the control pipe still uses
; the fake "maximum packet size". Call the controller-specific function to
; change it to the actual packet size from the device.
; Note that the hardware could cache the controller-specific structure,
; so changing it could take some time until the cache is evicted.
; Thus, the call is asynchronous; meet us in usb_after_set_endpoint_size
; when it will be safe to continue.
movzx ecx, [eax+usb_device_data.DeviceDescriptor+usb_device_descr.bMaxPacketSize0]
mov eax, [esi+usb_controller.HardwareFunc]
call [eax+usb_hardware_func.SetEndpointPacketSize]
.nothing:
; 5. Return.
pop ebx edi ; restore used registers to be stdcall
ret
.error:
dbgstr 'error with USB device descriptor'
jmp .nothing
endp
; This procedure is called from usb_subscription_done when the hardware cache
; is cleared after request from usb_get_descr8_callback.
; in: ebx -> usb_pipe
proc usb_after_set_endpoint_size
; 1. Reallocate memory for device data:
; add memory for now-known size of device descriptor and extra 8 bytes
; for further actions.
; 1a. Allocate new memory.
mov eax, [ebx+usb_pipe.DeviceData]
movzx eax, [eax+usb_device_data.DeviceDescriptor+usb_device_descr.bLength]
; save length for step 2
push eax
add eax, sizeof.usb_device_data + 8
call malloc
; 1b. If failed, say something to the debug board and stop the initialization.
test eax, eax
jz .nomemory
; 1c. Copy data from old memory to new memory and switch the pointer in usb_pipe.
push eax
push esi edi
mov esi, [ebx+usb_pipe.DeviceData]
mov [ebx+usb_pipe.DeviceData], eax
mov edi, eax
mov eax, esi
mov ecx, sizeof.usb_device_data / 4
rep movsd
pop edi esi
call usb_reinit_pipe_list
; 1d. Free the old memory.
call free
pop eax
; 2. Issue control transfer GET_DESCRIPTOR(DEVICE) for full descriptor.
; restore length saved in step 1a
pop edx
add eax, sizeof.usb_device_data
mov dword [eax], \
80h + \ ; device-to-host, standard, device-wide
(USB_GET_DESCRIPTOR shl 8) + \ ; request
(0 shl 16) + \ ; descriptor index: there is only one
(USB_DEVICE_DESCR shl 24) ; descriptor type
and dword [eax+4], 0
mov [eax+6], dl ; data length
stdcall usb_control_async, ebx, eax, eax, edx, usb_get_descr_callback, eax, 0
; 3. Return.
ret
.nomemory:
dbgstr 'No memory for device data'
ret
endp
; This procedure is called by USB stack when GET_DESCRIPTOR(DEVICE)
; request initiated by usb_after_set_endpoint_size is completed,
; either successfully or unsuccessfully.
proc usb_get_descr_callback stdcall, pipe:dword, status:dword, buffer:dword, length:dword, calldata:dword
; Note: the prolog is the same as in usb_get_descr8_callback.
push edi ebx ; save used registers to be stdcall
; 1. Check whether the operation was successful.
; If not, say something to the debug board and stop the initialization.
cmp [status], 0
jnz usb_get_descr8_callback.error
; The full descriptor is known, dump it if specified by compile-time option.
if USB_DUMP_DESCRIPTORS
mov eax, [buffer]
mov ecx, [length]
sub ecx, 8
jbe .skipdebug
DEBUGF 1,'K : device descriptor:'
@@:
DEBUGF 1,' %x',[eax]:2
inc eax
dec ecx
jnz @b
DEBUGF 1,'\n'
.skipdebug:
end if
; 2. Check that bLength is the same as was in the previous request.
; If not, say something to the debug board and stop the initialization.
; It is important, because usb_after_set_endpoint_size has allocated memory
; according to the old bLength. Note that [length] for control transfers
; includes 8 bytes of setup packet, so data length = [length] - 8.
mov eax, [buffer]
movzx ecx, [eax+usb_device_descr.bLength]
add ecx, 8
cmp [length], ecx
jnz usb_get_descr8_callback.error
; Amuse the user if she is watching the debug board.
mov cl, [eax+usb_device_descr.bNumConfigurations]
DEBUGF 1,'K : found USB device with ID %x:%x, %d configuration(s)\n',\
[eax+usb_device_descr.idVendor]:4,\
[eax+usb_device_descr.idProduct]:4,\
cl
; 3. If there are no configurations, stop the initialization.
cmp [eax+usb_device_descr.bNumConfigurations], 0
jz .nothing
; 4. Copy length of device descriptor to device data structure.
movzx edx, [eax+usb_device_descr.bLength]
mov [eax+usb_device_data.DeviceDescrSize-usb_device_data.DeviceDescriptor], dl
; 5. Issue control transfer GET_DESCRIPTOR(CONFIGURATION). We do not know
; the full length of that descriptor, so start with first 8 bytes, they contain
; the full length.
; usb_after_set_endpoint_size has allocated 8 extra bytes after the
; device descriptor, use them for both input and output.
add eax, edx
mov dword [eax], \
80h + \ ; device-to-host, standard, device-wide
(USB_GET_DESCRIPTOR shl 8) + \ ; request
(0 shl 16) + \ ; descriptor index: there is only one
(USB_CONFIG_DESCR shl 24) ; descriptor type
mov dword [eax+4], 8 shl 16 ; data length
stdcall usb_control_async, [pipe], eax, eax, 8, usb_know_length_callback, eax, 0
.nothing:
; 6. Return.
pop ebx edi ; restore used registers to be stdcall
ret
endp
; This procedure is called by USB stack when GET_DESCRIPTOR(CONFIGURATION)
; request initiated by usb_get_descr_callback is completed,
; either successfully or unsuccessfully.
proc usb_know_length_callback stdcall, pipe:dword, status:dword, buffer:dword, length:dword, calldata:dword
push ebx ; save used registers to be stdcall
; 1. Check whether the operation was successful.
; If not, say something to the debug board and stop the initialization.
cmp [status], 0
jnz .error
; 2. Get the total length of data associated with config descriptor and store
; it in device data structure. The total length must be at least
; sizeof.usb_config_descr bytes; if not, say something to the debug board and
; stop the initialization.
mov eax, [buffer]
mov edx, [pipe]
movzx ecx, [eax+usb_config_descr.wTotalLength]
mov eax, [edx+usb_pipe.DeviceData]
cmp ecx, sizeof.usb_config_descr
jb .error
mov [eax+usb_device_data.ConfigDataSize], ecx
; 3. Reallocate memory for device data:
; include usb_device_data structure, device descriptor,
; config descriptor with all associated data, and extra bytes
; sufficient for 8 bytes control packet and for one usb_interface_data struc.
; Align extra bytes to dword boundary.
if sizeof.usb_interface_data > 8
.extra_size = sizeof.usb_interface_data
else
.extra_size = 8
end if
; 3a. Allocate new memory.
movzx edx, [eax+usb_device_data.DeviceDescrSize]
lea eax, [ecx+edx+sizeof.usb_device_data+.extra_size+3]
and eax, not 3
push eax
call malloc
pop edx
; 3b. If failed, say something to the debug board and stop the initialization.
test eax, eax
jz .nomemory
; 3c. Copy data from old memory to new memory and switch the pointer in usb_pipe.
push eax
mov ebx, [pipe]
push esi edi
mov esi, [ebx+usb_pipe.DeviceData]
mov edi, eax
mov [ebx+usb_pipe.DeviceData], eax
mov eax, esi
movzx ecx, [esi+usb_device_data.DeviceDescrSize]
sub edx, .extra_size
mov [esi+usb_device_data.Interfaces], edx
add ecx, sizeof.usb_device_data + 8
mov edx, ecx
shr ecx, 2
and edx, 3
rep movsd
mov ecx, edx
rep movsb
pop edi esi
call usb_reinit_pipe_list
; 3d. Free old memory.
call free
pop eax
; 4. Issue control transfer GET_DESCRIPTOR(DEVICE) for full descriptor.
movzx ecx, [eax+usb_device_data.DeviceDescrSize]
mov edx, [eax+usb_device_data.ConfigDataSize]
lea eax, [eax+ecx+sizeof.usb_device_data]
mov dword [eax], \
80h + \ ; device-to-host, standard, device-wide
(USB_GET_DESCRIPTOR shl 8) + \ ; request
(0 shl 16) + \ ; descriptor index: there is only one
(USB_CONFIG_DESCR shl 24) ; descriptor type
and dword [eax+4], 0
mov word [eax+6], dx ; data length
stdcall usb_control_async, [pipe], eax, eax, edx, usb_set_config_callback, eax, 0
.nothing:
; 5. Return.
pop ebx ; restore used registers to be stdcall
ret
.error:
dbgstr 'error with USB configuration descriptor'
jmp .nothing
.nomemory:
dbgstr 'No memory for device data'
jmp .nothing
endp
; This procedure is called by USB stack when GET_DESCRIPTOR(CONFIGURATION)
; request initiated by usb_know_length_callback is completed,
; either successfully or unsuccessfully.
proc usb_set_config_callback stdcall, pipe:dword, status:dword, buffer:dword, length:dword, calldata:dword
; Note that the prolog is the same as in usb_know_length_callback.
push ebx ; save used registers to be stdcall
; 1. Check whether the operation was successful.
; If not, say something to the debug board and stop the initialization.
xor ecx, ecx
mov ebx, [pipe]
cmp [status], ecx
jnz usb_know_length_callback.error
; The full descriptor is known, dump it if specified by compile-time option.
if USB_DUMP_DESCRIPTORS
mov eax, [buffer]
mov ecx, [length]
sub ecx, 8
jbe .skip_debug
DEBUGF 1,'K : config descriptor:'
@@:
DEBUGF 1,' %x',[eax]:2
inc eax
dec ecx
jnz @b
DEBUGF 1,'\n'
.skip_debug:
xor ecx, ecx
end if
; 2. Issue control transfer SET_CONFIGURATION to activate this configuration.
; Usually this is the only configuration.
; Use extra bytes allocated by usb_know_length_callback;
; offset from device data start is stored in Interfaces.
mov eax, [ebx+usb_pipe.DeviceData]
mov edx, [buffer]
add eax, [eax+usb_device_data.Interfaces]
mov dl, [edx+usb_config_descr.bConfigurationValue]
mov dword [eax], USB_SET_CONFIGURATION shl 8
mov dword [eax+4], ecx
mov byte [eax+2], dl
stdcall usb_control_async, [pipe], eax, ecx, ecx, usb_got_config_callback, [buffer], ecx
pop ebx ; restore used registers to be stdcall
ret
endp
; This procedure is called by USB stack when SET_CONFIGURATION
; request initiated by usb_set_config_callback is completed,
; either successfully or unsuccessfully.
; If successfully, the device is configured and ready to work,
; pass the device to the corresponding driver(s).
proc usb_got_config_callback stdcall, pipe:dword, status:dword, buffer:dword, length:dword, calldata:dword
locals
InterfacesData dd ?
NumInterfaces dd ?
driver dd ?
endl
; 1. If there was an error, say something to the debug board and stop the
; initialization.
cmp [status], 0
jz @f
dbgstr 'USB error in SET_CONFIGURATION'
ret
@@:
push ebx edi ; save used registers to be stdcall
; 2. Sanity checks: the total length must be the same as before (because we
; have allocated memory assuming the old value), length of config descriptor
; must be at least sizeof.usb_config_descr (we use fields from it),
; there must be at least one interface.
mov ebx, [pipe]
mov ebx, [ebx+usb_pipe.DeviceData]
mov eax, [calldata]
mov edx, [ebx+usb_device_data.ConfigDataSize]
cmp [eax+usb_config_descr.wTotalLength], dx
jnz .invalid
cmp [eax+usb_config_descr.bLength], 9
jb .invalid
movzx edx, [eax+usb_config_descr.bNumInterfaces]
test edx, edx
jnz @f
.invalid:
dbgstr 'error: invalid configuration descriptor'
jmp .nothing
@@:
; 3. Store the number of interfaces in device data structure.
mov [ebx+usb_device_data.NumInterfaces], edx
; 4. If there is only one interface (which happens quite often),
; the memory allocated in usb_know_length_callback is sufficient.
; Otherwise (which also happens quite often), reallocate device data.
; 4a. Check whether there is only one interface. If so, skip this step.
cmp edx, 1
jz .has_memory
; 4b. Allocate new memory.
mov eax, [ebx+usb_device_data.Interfaces]
lea eax, [eax+edx*sizeof.usb_interface_data]
call malloc
; 4c. If failed, say something to the debug board and
; stop the initialization.
test eax, eax
jnz @f
dbgstr 'No memory for device data'
jmp .nothing
@@:
; 4d. Copy data from old memory to new memory and switch the pointer in usb_pipe.
push eax
push esi
mov ebx, [pipe]
mov edi, eax
mov esi, [ebx+usb_pipe.DeviceData]
mov [ebx+usb_pipe.DeviceData], eax
mov eax, esi
mov ecx, [esi+usb_device_data.Interfaces]
shr ecx, 2
rep movsd
pop esi
call usb_reinit_pipe_list
; 4e. Free old memory.
call free
pop ebx
.has_memory:
; 5. Initialize interfaces table: zero all contents.
mov edi, [ebx+usb_device_data.Interfaces]
add edi, ebx
mov [InterfacesData], edi
mov ecx, [ebx+usb_device_data.NumInterfaces]
if sizeof.usb_interface_data <> 8
You have changed sizeof.usb_interface_data? Modify this place too.
end if
add ecx, ecx
xor eax, eax
rep stosd
; No interfaces are found yet.
mov [NumInterfaces], eax
; 6. Get the pointer to config descriptor data.
; Note: if there was reallocation, [buffer] is not valid anymore,
; so calculate value based on usb_device_data.
movzx eax, [ebx+usb_device_data.DeviceDescrSize]
lea eax, [eax+ebx+sizeof.usb_device_data]
mov [calldata], eax
mov ecx, [ebx+usb_device_data.ConfigDataSize]
; 7. Loop over all descriptors,
; scan for interface descriptors with bAlternateSetting = 0,
; load the corresponding driver, call its AddDevice function.
.descriptor_loop:
; While in loop: eax points to the current descriptor,
; ecx = number of bytes left, the iteration starts only if ecx is nonzero,
; edx = size of the current descriptor.
; 7a. The first byte is always accessible; it contains the length of
; the current descriptor. Validate that the length is at least 2 bytes,
; and the entire descriptor is readable (the length is at most number of
; bytes left).
movzx edx, [eax+usb_descr.bLength]
cmp edx, sizeof.usb_descr
jb .invalid
cmp ecx, edx
jb .invalid
; 7b. Check descriptor type. Ignore all non-INTERFACE descriptor.
cmp byte [eax+usb_descr.bDescriptorType], USB_INTERFACE_DESCR
jz .interface
.next_descriptor:
; 7c. Advance pointer, decrease length left, if there is still something left,
; continue the loop.
add eax, edx
sub ecx, edx
jnz .descriptor_loop
.done:
.nothing:
pop edi ebx ; restore used registers to be stdcall
ret
.interface:
; 7d. Validate the descriptor length.
cmp edx, sizeof.usb_interface_descr
jb .next_descriptor
; 7e. If bAlternateSetting is nonzero, this descriptor actually describes
; another mode of already known interface and belongs to the already loaded
; driver; amuse the user and continue to 7c.
cmp byte [eax+usb_interface_descr.bAlternateSetting], 0
jz @f
DEBUGF 1,'K : note: alternate setting with %x/%x/%x\n',\
[eax+usb_interface_descr.bInterfaceClass]:2,\
[eax+usb_interface_descr.bInterfaceSubClass]:2,\
[eax+usb_interface_descr.bInterfaceProtocol]:2
jmp .next_descriptor
@@:
; 7f. Check that the new interface does not overflow allocated table.
mov edx, [NumInterfaces]
inc edx
cmp edx, [ebx+usb_device_data.NumInterfaces]
ja .invalid
; 7g. We have found a new interface. Advance bookkeeping vars.
mov [NumInterfaces], edx
add [InterfacesData], sizeof.usb_interface_data
; 7h. Save length left and pointer to the current interface descriptor.
push ecx eax
; Amuse the user if she is watching the debug board.
DEBUGF 1,'K : USB interface class/subclass/protocol = %x/%x/%x\n',\
[eax+usb_interface_descr.bInterfaceClass]:2,\
[eax+usb_interface_descr.bInterfaceSubClass]:2,\
[eax+usb_interface_descr.bInterfaceProtocol]:2
; 7i. Select the correct driver based on interface class.
; For hubs, go to 7j. Otherwise, go to 7k.
; Note: this should be rewritten as table-based lookup when more drivers will
; be available.
cmp byte [eax+usb_interface_descr.bInterfaceClass], 9
jz .found_hub
mov edx, usb_hid_name
cmp byte [eax+usb_interface_descr.bInterfaceClass], 3
jz .load_driver
mov edx, usb_print_name
cmp byte [eax+usb_interface_descr.bInterfaceClass], 7
jz .load_driver
mov edx, usb_stor_name
cmp byte [eax+usb_interface_descr.bInterfaceClass], 8
jz .load_driver
mov edx, usb_other_name
jmp .load_driver
.found_hub:
; 7j. Hubs are a part of USB stack, thus, integrated into the kernel.
; Use the pointer to hub callbacks and go to 7m.
mov eax, usb_hub_pseudosrv - USBSRV.usb_func
jmp .driver_loaded
.load_driver:
; 7k. Load the corresponding driver.
push ebx esi edi
stdcall get_service, edx
pop edi esi ebx
; 7l. If failed, say something to the debug board and go to 7p.
test eax, eax
jnz .driver_loaded
dbgstr 'failed to load class driver'
jmp .next_descriptor2
.driver_loaded:
; 7m. Call AddDevice function of the driver.
; Note that top of stack contains a pointer to the current interface,
; saved by step 7h.
mov [driver], eax
mov eax, [eax+USBSRV.usb_func]
pop edx
push edx
; Note: usb_hub_init assumes that edx points to usb_interface_descr,
; ecx = length rest; if you change the code, modify usb_hub_init also.
stdcall [eax+USBFUNC.add_device], [pipe], [calldata], edx
; 7n. If failed, say something to the debug board and go to 7p.
test eax, eax
jnz .store_data
dbgstr 'USB device initialization failed'
jmp .next_descriptor2
.store_data:
; 7o. Store the returned value and the driver handle to InterfacesData.
; Note that step 7g has already advanced InterfacesData.
mov edx, [InterfacesData]
mov [edx+usb_interface_data.DriverData-sizeof.usb_interface_data], eax
mov eax, [driver]
mov [edx+usb_interface_data.DriverFunc-sizeof.usb_interface_data], eax
.next_descriptor2:
; 7p. Restore registers saved in step 7h, get the descriptor length and
; continue to 7c.
pop eax ecx
movzx edx, byte [eax+usb_descr.bLength]
jmp .next_descriptor
endp
; Driver names, see step 7i of usb_got_config_callback.
iglobal
usb_hid_name db 'usbhid',0
usb_stor_name db 'usbstor',0
usb_print_name db 'usbprint',0
usb_other_name db 'usbother',0
endg