keXa/kolibrios
1
0
Fork 0
forked from KolibriOS/kolibrios
Code Pull Requests Activity

Fixed eeprom reading for certain chips, detect PHY ID, improved reset.

Browse Source 
git-svn-id: svn://kolibrios.org@6717 a494cfbc-eb01-0410-851d-a64ba20cac60
This commit is contained in:
hidnplayr 2016-11-15 21:34:09 +00:00
parent 4fcfa2351b
commit 97e49e498f
1 changed files with 161 additions and 154 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

315
drivers/ethernet/i8255x.asm
View File

@ -1,6 +1,6 @@
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;; ;;
;; Copyright (C) KolibriOS team 2004-2015. All rights reserved. ;;
;; Copyright (C) KolibriOS team 2004-2016. All rights reserved. ;;
;; Distributed under terms of the GNU General Public License ;;
;; ;;
;; i8255x (Intel eepro 100) driver for KolibriOS ;;
@ -43,53 +43,59 @@ include '../macros.inc'
include '../fdo.inc'
include '../netdrv.inc'
; I/O registers
REG_SCB_STATUS = 0
REG_SCB_CMD = 2
REG_SCB_PTR = 4
REG_PORT = 8
REG_EEPROM = 14
REG_MDI_CTRL = 16
; Port commands
PORT_SOFT_RESET = 0x0
PORT_SELF_TEST = 0x1
PORT_SELECTIVE_RESET = 0x2
PORT_DUMP = 0x3
PORT_DUMP_WAKEUP = 0x7
PORT_PTR_MASK = 0xfffffff0
; Serial EEPROM
EE_SK = 1 shl 0 ; serial clock
EE_CS = 1 shl 1 ; chip select
EE_DI = 1 shl 2 ; data in
EE_DO = 1 shl 3 ; data out
EE_MASK = EE_SK + EE_CS + EE_DI + EE_DO
EE_SK = 1 shl 0 ; serial clock
EE_CS = 1 shl 1 ; chip select
EE_DI = 1 shl 2 ; data in
EE_DO = 1 shl 3 ; data out
EE_MASK = EE_SK + EE_CS + EE_DI + EE_DO
; opcodes, first bit is start bit and must be 1
EE_READ = 110b
EE_WRITE = 101b
EE_ERASE = 111b
EE_READ = 110b
EE_WRITE = 101b
EE_ERASE = 111b
; The SCB accepts the following controls for the Tx and Rx units:
CU_START = 0x0010
CU_RESUME = 0x0020
CU_STATSADDR = 0x0040
CU_SHOWSTATS = 0x0050 ; Dump statistics counters.
CU_CMD_BASE = 0x0060 ; Base address to add CU commands.
CU_DUMPSTATS = 0x0070 ; Dump then reset stats counters.
CU_START = 0x0010
CU_RESUME = 0x0020
CU_STATSADDR = 0x0040
CU_SHOWSTATS = 0x0050 ; Dump statistics counters.
CU_CMD_BASE = 0x0060 ; Base address to add CU commands.
CU_DUMPSTATS = 0x0070 ; Dump then reset stats counters.
RX_START = 0x0001
RX_RESUME = 0x0002
RX_ABORT = 0x0004
RX_ADDR_LOAD = 0x0006
RX_RESUMENR = 0x0007
INT_MASK = 0x0100
DRVR_INT = 0x0200 ; Driver generated interrupt
RX_START = 0x0001
RX_RESUME = 0x0002
RX_ABORT = 0x0004
RX_ADDR_LOAD = 0x0006
RX_RESUMENR = 0x0007
INT_MASK = 0x0100
DRVR_INT = 0x0200 ; Driver generated interrupt
REG_SCB_STATUS = 0
REG_SCB_CMD = 2
REG_SCB_PTR = 4
REG_PORT = 8
REG_EEPROM = 14
REG_MDI_CTRL = 16
PHY_100a = 0x000003E0
PHY_100c = 0x035002A8
PHY_82555_tx = 0x015002A8
PHY_nsc_tx = 0x5C002000
PHY_82562_et = 0x033002A8
PHY_82562_em = 0x032002A8
PHY_82562_ek = 0x031002A8
PHY_82562_eh = 0x017002A8
PHY_82552_v = 0xd061004d
PHY_unknown = 0xFFFFFFFF
PHY_100a = 0x000003E0
PHY_100c = 0x035002A8
PHY_82555_tx = 0x015002A8
PHY_nsc_tx = 0x5C002000
PHY_82562_et = 0x033002A8
PHY_82562_em = 0x032002A8
PHY_82562_ek = 0x031002A8
PHY_82562_eh = 0x017002A8
PHY_82552_v = 0xd061004d
PHY_unknown = 0xFFFFFFFF
MAC_82557_D100_A = 0
MAC_82557_D100_B = 1
@ -318,7 +324,7 @@ proc service_proc stdcall, ioctl:dword
mov [ebx + device.reset], reset
mov [ebx + device.transmit], transmit
mov [ebx + device.unload], unload
mov [ebx + device.name], my_service
mov [ebx + device.name], devicename
; save the pci bus and device numbers
@ -338,23 +344,18 @@ proc service_proc stdcall, ioctl:dword
invoke PciRead8, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.interrupt_line
mov [ebx + device.irq_line], al
DEBUGF 1,"Hooking into device, dev:%x, bus:%x, irq:%x, addr:%x\n",\
[ebx + device.pci_dev]:1,[ebx + device.pci_bus]:1,[ebx + device.irq_line]:1,[ebx + device.io_addr]:4
DEBUGF 1,"Hooking into device, devfn:%x, bus:%x, irq:%x, addr:%x\n",\
[ebx + device.pci_dev]:2,[ebx + device.pci_bus]:2,[ebx + device.irq_line]:2,[ebx + device.io_addr]:4
; Ok, the eth_device structure is ready, let's probe the device
pushf
cli ; disable ints untilm initialisation is done
call probe ; this function will output in eax
test eax, eax
jnz .err ; If an error occured, exit
mov eax, [devices] ; Add the device structure to our device list
mov [device_list+4*eax], ebx ; (IRQ handler uses this list to find device)
inc [devices] ;
popf
call probe ; this function will output in eax
test eax, eax
jnz .err ; If an error occured, exit
mov [ebx + device.type], NET_TYPE_ETH
invoke NetRegDev
@ -375,7 +376,6 @@ proc service_proc stdcall, ioctl:dword
ret
; If an error occured, remove all allocated data and exit (returning -1 in eax)
.err:
invoke KernelFree, ebx
@ -423,7 +423,7 @@ probe:
; Make the device a bus master
invoke PciRead32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command
or al, PCI_CMD_MASTER
or al, PCI_CMD_MASTER or PCI_CMD_PIO
invoke PciWrite32, [ebx + device.pci_bus], [ebx + device.pci_dev], PCI_header00.command, eax
;---------------------------
@ -452,11 +452,6 @@ probe:
.found:
call ee_get_width
call MAC_read_eeprom
;;; TODO: detect phy
;----------
@ -480,16 +475,45 @@ reset:
DEBUGF 1,"Resetting\n"
;---------------
; reset the card
;----------------
; Selective reset
set_io [ebx + device.io_addr], 0
set_io [ebx + device.io_addr], REG_EEPROM
mov eax, PORT_SELECTIVE_RESET
out dx, eax
mov esi, 1
invoke Sleep
;-----------
; Soft reset
set_io [ebx + device.io_addr], REG_PORT
xor eax, eax ; Software Reset
mov eax, PORT_SOFT_RESET
out dx, eax
mov esi, 10
invoke Sleep ; Give the card time to warm up.
invoke Sleep
;-------------
; Read PHY IDs
mov cx, 1
mov dx, MII_PHYSID1
call mdio_read
DEBUGF 1, "PHY ID1: 0x%x\n", ax
mov cx, 1
mov dx, MII_PHYSID2
call mdio_read
DEBUGF 1, "PHY ID2: 0x%x\n", ax
;---------------------
; Read MAC from eeprom
call ee_get_width
call mac_read_eeprom
;---------------------------------
; Tell device where to store stats
@ -810,7 +834,7 @@ int_handler:
pop edi esi ebx
xor eax, eax
ret ; If no device was found, abort (The irq was probably for a device, not registered to this driver)
ret ; If no device was found, abort (The irq was probably for a device, not registered to this driver)
.got_it:
@ -991,15 +1015,15 @@ ee_read: ; esi = address to read
movzx ecx, [ebx + device.ee_bus_width]
add ecx, 3
mov al, EE_CS
out dx, al
mov ax, 0x4800 + EE_CS
out dx, ax
call udelay
;-----------------------
; Write this to the chip
.loop:
mov al, EE_CS + EE_SK
mov al, EE_CS
shl esi, 1
jnc @f
or al, EE_DI
@ -1007,7 +1031,7 @@ ee_read: ; esi = address to read
out dx, al
call udelay
and al, not EE_SK
or al, EE_SK
out dx, al
call udelay
@ -1021,7 +1045,11 @@ ee_read: ; esi = address to read
.loop2:
shl esi, 1
mov al, EE_CS + EE_SK
mov al, EE_CS
out dx, al
call udelay
or al, EE_SK
out dx, al
call udelay
@ -1031,18 +1059,13 @@ ee_read: ; esi = address to read
inc esi
@@:
mov al, EE_CS
out dx, al
call udelay
loop .loop2
;-----------------------
; de-activate the eeprom
xor ax, ax
out dx, ax
xor al, al
out dx, al
DEBUGF 1,"0x%x\n", esi:4
ret
@ -1069,14 +1092,14 @@ ee_write: ; esi = address to write to, di = data
movzx ecx, [ebx + device.ee_bus_width]
add ecx, 3
mov al, EE_CS ; enable chip
out dx, al
mov ax, 0x4800 + EE_CS ; enable chip
out dx, ax
;-----------------------
; Write this to the chip
.loop:
mov al, EE_CS + EE_SK
mov al, EE_CS
shl esi, 1
jnc @f
or al, EE_DI
@ -1084,7 +1107,7 @@ ee_write: ; esi = address to write to, di = data
out dx, al
call udelay
and al, not EE_SK
or al, EE_SK
out dx, al
call udelay
@ -1096,7 +1119,7 @@ ee_write: ; esi = address to write to, di = data
mov ecx, 16
.loop2:
mov al, EE_CS + EE_SK
mov al, EE_CS
shl di, 1
jnc @f
or al, EE_DI
@ -1104,7 +1127,7 @@ ee_write: ; esi = address to write to, di = data
out dx, al
call udelay
and al, not EE_SK
or al, EE_SK
out dx, al
call udelay
@ -1127,23 +1150,23 @@ ee_get_width:
set_io [ebx + device.io_addr], 0
set_io [ebx + device.io_addr], REG_EEPROM
mov al, EE_CS ; activate eeprom
out dx, al
mov ax, 0x4800 + EE_CS ; activate eeprom
out dx, ax
call udelay
mov si, EE_READ shl 13
xor ecx, ecx
.loop:
mov al, EE_CS + EE_SK
mov al, EE_CS
shl si, 1
jnc @f
or al, EE_DI
@@:
out dx, al
out dx, ax
call udelay
and al, not EE_SK
out dx, al
or al, EE_SK
out dx, ax
call udelay
inc ecx
@ -1156,9 +1179,9 @@ ee_get_width:
jnz .loop
xor al, al
out dx, al ; de-activate eeprom
out dx, al ; de-activate eeprom
sub cl, 3 ; dont count the opcode bits
sub cl, 3 ; dont count the opcode bits
mov [ebx + device.ee_bus_width], cl
DEBUGF 1, "Eeprom width=%u bit\n", ecx
@ -1166,9 +1189,8 @@ ee_get_width:
.give_up:
DEBUGF 2, "Eeprom not found!\n"
xor al, al
out dx, al ; de-activate eeprom
out dx, al ; de-activate eeprom
ret
@ -1195,9 +1217,8 @@ mdio_read:
DEBUGF 1,"MDIO read\n"
shl ecx, 21 ; PHY addr
shl edx, 16 ; PHY reg addr
mov eax, ecx
shl edx, 16 ; PHY reg addr
or eax, edx
or eax, 10b shl 26 ; read opcode
@ -1213,6 +1234,8 @@ mdio_read:
ret
; ax = data
; cx = phy addr
; dx = phy reg addr
@ -1245,14 +1268,9 @@ mdio_write:
ret
read_mac:
ret
align 4
MAC_read_eeprom:
mac_read_eeprom:
mov esi, 0
call ee_read
@ -1270,16 +1288,6 @@ MAC_read_eeprom:
ret
align 4
MAC_write:
;;;;
ret
; End of code
@ -1297,49 +1305,48 @@ confcmd_data db 22, 0x08, 0, 0, 0, 0x80, 0x32, 0x03, 1
device_id_list:
dw 0x1029
dw 0x1030
dw 0x1031
dw 0x1032
dw 0x1033
dw 0x1034
dw 0x1038
dw 0x1039
dw 0x103A
dw 0x103B
dw 0x103C
dw 0x103D
dw 0x103E
dw 0x1050
dw 0x1051
dw 0x1052
dw 0x1053
dw 0x1054
dw 0x1055
dw 0x1056
dw 0x1057
dw 0x1059
dw 0x1064
dw 0x1065
dw 0x1066
dw 0x1067
dw 0x1068
dw 0x1069
dw 0x106A
dw 0x106B
dw 0x1091
dw 0x1092
dw 0x1093
dw 0x1094
dw 0x1095
dw 0x10fe
dw 0x1209
dw 0x1229
dw 0x2449
dw 0x2459
dw 0x245D
dw 0x27DC
dw 0x1029
dw 0x1030
dw 0x1031
dw 0x1032
dw 0x1033
dw 0x1034
dw 0x1038
dw 0x1039
dw 0x103A
dw 0x103B
dw 0x103C
dw 0x103D
dw 0x103E
dw 0x1050
dw 0x1051
dw 0x1052
dw 0x1053
dw 0x1054
dw 0x1055
dw 0x1056
dw 0x1057
dw 0x1059
dw 0x1064
dw 0x1065
dw 0x1066
dw 0x1067
dw 0x1068
dw 0x1069
dw 0x106A
dw 0x106B
dw 0x1091
dw 0x1092
dw 0x1093
dw 0x1094
dw 0x1095
dw 0x10fe
dw 0x1209
dw 0x1229
dw 0x2449
dw 0x2459
dw 0x245D
dw 0x27DC
DEVICE_IDs = ($ - device_id_list) / 2